Dragon box Pinfinding Problem Solved Check out ! - GSM-Forum

Faheem Anjum · 12-30-2011, 14:50

Solution:

Open your Gpg Dragon box
Connect your box to A-B connector
While your box is connected, connect you multitester rod shown to this image...
after you hear a beep....disconect mutitester....
then disconnect A-B connector...
then wait a few minutes.....
then reconnect box...
then upgrade your box firmware to this: Firmware 1.58
then your box is back to work again....

Thanks So much aermacchi ,Uttam , Awais Nawab shoo , haq nawaz for Test !

m.awais.as · 12-30-2011, 14:53

yes this is perfect solution

my box is working fine

thankx gpg team

faheem anjum

br,

AM_GSM_CELL...:::M.AWAIS.AS:::...

uttam · 12-30-2011, 15:01

Thanks You
@ Faheem Anjum
Successfully Repair My Box Problem Of Can,t Find Pin out After Update 1.59 Firmware....
Most Helpful Team ..

BR
Uttam

kush202002 · 12-30-2011, 15:11

Whts abt new firmware of 1.59....how v go tht after back to 1.58....

Faheem Anjum · 12-30-2011, 15:15

Quote:

Originally Posted by kush202002

Whts abt new firmware of 1.59....how v go tht after back to 1.58....

you can update to any firmware after that ,

dahuratu · 12-30-2011, 15:16

could you please help me, I soldered two points, connect the multitester but not hear the beep

uttam · 12-30-2011, 15:22

Quote:

Originally Posted by dahuratu

could you please help me, I soldered two points, connect the multitester but not hear the beep

Set the multimeter as Quntinity(Beep) Mode And Connect + and - Point in Dragon-Box PCB..

RAGHAVENDRA4 · 12-30-2011, 15:29

thanks my brother working my box fine

wilmer · 12-30-2011, 15:35

so we can work with 1.58 and last version or we have to update to 1.59 them start working with 2.11 ? let us now

Faheem Anjum · 12-31-2011, 08:10

Quote:

Originally Posted by wilmer

so we can work with 1.58 and last version or we have to update to 1.59 them start working with 2.11 ? let us now

http://forum.gsmhosting.com/vbb/8030545-post5.html

mfq · 12-31-2011, 08:36

Thanks My problem solved by Faheem Anjum

NKhan_Gsm · 12-31-2011, 09:13

Now the error

Quote:

>>> Firmware file : 39680 Byte
>>> Port poen ok......
>>> Conjunction box......
>>> Conjunction box error!!!

during firmware upgrade and as its solution was already given by Mr. SHIJILFONOTLY I did all according that sticky post but still same Error during firmware upgrade please help GPG Team.

WBR

Faheem Anjum · 12-31-2011, 10:05

Quote:

Originally Posted by NKhan_Gsm

Now the error during firmware upgrade and as its solution was already given by Mr. SHIJILFONOTLY I did all according that sticky post but still same Error during firmware upgrade please help GPG Team.

WBR

Some User Still Not Get the point No Need to Short Both point As i show on Pic just keep the rod on + and - well try to make a Video For That

like this

If you of the box can't normally start...
Pull out USB cable...
The short circuit red and black cable clip...
Contact USB cable...
Box exigency mode, then got upgrade...

NKhan_Gsm · 12-31-2011, 10:20

Thanks problem solved box firmware successfully upgraded via Exigency Upgrade mode and short circuit ( Red & Black power cables should be connected to each other during firmware update ) .
Thanks to GPG Team Specially to Mr.Faheem Anjum .

WBR

Ali Ahammad · 12-31-2011, 10:35

Update successful

try 5-6 time then update

good work gpg team

12-30-2011, 14:50	#1 (permalink)
Faheem Anjum No Life Poster Join Date: Nov 2006 Location: (United States Of Islam) Age: 37 Posts: 24,984 Member: 399832 Status: Offline Sonork: Faheem Anjum Thanks Meter: 24,310	Dragon box Pinfinding Problem Solved Check out ! Solution: Open your Gpg Dragon box Connect your box to A-B connector While your box is connected, connect you multitester rod shown to this image... after you hear a beep....disconect mutitester.... then disconnect A-B connector... then wait a few minutes..... then reconnect box... then upgrade your box firmware to this: Firmware 1.58 then your box is back to work again.... Thanks So much aermacchi ,Uttam , Awais Nawab shoo , haq nawaz for Test ! Last edited by Faheem Anjum; 12-31-2011 at 07:14.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
6150 Lock Problem	Zeljko	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	10-16-2013 08:16
GId1 problem	old_man	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	10-18-2006 15:21
Silly question!! Why is it impossible to read out the mastercode of Nokia phones????	MyKe	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	09-26-1999 14:31
HELP: Problem with 5110	Xabi	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	07-16-1999 00:44

12-30-2011, 14:53	#2 (permalink)
m.awais.as No Life Poster Join Date: Apr 2010 Location: Lahore Pakistan. Age: 38 Posts: 2,518 Member: 1284347 Status: Offline Sonork: 100.1592292 Thanks Meter: 977	yes this is perfect solution my box is working fine thankx gpg team faheem anjum br, AM_GSM_CELL...:::M.AWAIS.AS:::...

12-30-2011, 15:01	#3 (permalink)
uttam Freak Poster Join Date: Jan 2006 Location: India (Gujarat) Age: 36 Posts: 329 Member: 223135 Status: Offline Sonork: 100.1592685 Thanks Meter: 177	Thanks You @ Faheem Anjum Successfully Repair My Box Problem Of Can,t Find Pin out After Update 1.59 Firmware.... Most Helpful Team .. BR Uttam

12-30-2011, 15:11	#4 (permalink)
kush202002 Registered User Join Date: Aug 2010 Location: EVERY WHERE Age: 38 Posts: 504 Member: 1372393 Status: Offline Sonork: I.M.STORE Thanks Meter: 90	Whts abt new firmware of 1.59....how v go tht after back to 1.58....

12-30-2011, 15:16	#6 (permalink)
dahuratu Junior Member Join Date: Nov 2011 Posts: 37 Member: 1691127 Status: Offline Thanks Meter: 5	could you please help me, I soldered two points, connect the multitester but not hear the beep

12-30-2011, 15:29	#8 (permalink)
RAGHAVENDRA4 Freak Poster Join Date: Dec 2007 Location: INDIA Posts: 130 Member: 646199 Status: Offline Sonork: 100.1611318 Thanks Meter: 8	thanks my brother working my box fine

12-30-2011, 15:35	#9 (permalink)
wilmer No Life Poster Join Date: Nov 2006 Location: esmeraldas-ecuador Posts: 966 Member: 392589 Status: Offline Sonork: 1597152 Thanks Meter: 50	so we can work with 1.58 and last version or we have to update to 1.59 them start working with 2.11 ? let us now

12-31-2011, 08:36	#11 (permalink)
mfq No Life Poster Join Date: Jul 2009 Location: pakistan Posts: 881 Member: 1083358 Status: Offline Thanks Meter: 199	Thanks My problem solved by Faheem Anjum

12-31-2011, 10:20	#14 (permalink)
NKhan_Gsm No Life Poster Join Date: Aug 2011 Location: Afghanistan Posts: 1,757 Member: 1646177 Status: Offline Sonork: 100.1604654 Thanks Meter: 369	Thanks problem solved box firmware successfully upgraded via Exigency Upgrade mode and short circuit ( Red & Black power cables should be connected to each other during firmware update ) . Thanks to GPG Team Specially to Mr.Faheem Anjum . WBR

12-31-2011, 10:35	#15 (permalink)
Ali Ahammad Freak Poster Join Date: Jul 2010 Location: Daudkandi,Comilla,Bangladesh. Posts: 221 Member: 1350057 Status: Offline Sonork: Not use Thanks Meter: 36	Update successful try 5-6 time then update good work gpg team