t585 isp connection failed ERROR[009] [Answered] - GSM-Forum

Master-ZizO · 01-24-2021, 15:21

Quote:

Socket detected!

Selected PIN - CONNECTOR.

Please disconnect battery and USB cable.

Model Settings:
Interface : eMMC
Voltage : 1.8V
Bus Mode : 1 bit
Bus speed : Auto

Pin connector is detected!(eMMC: 1b, UFS: PWM 1-4)

Connecting...

ERROR[009]: EXT CSD error(check voltage/bus mode)

i tried all voltages

andrei_d1978 · 01-24-2021, 16:14

Do you supply power via vcc and vccq?
The photo is poorly visible

Master-ZizO · 01-24-2021, 16:37

yes vcc and vccq connected to adapter .. same connection success with UFI

Master-ZizO · 01-31-2021, 20:07

I'm new to Medusa stuff .. i just bought it 2 weaks ago!

Medusa Box · 02-01-2021, 10:26

Hello.

Check if the connections are correct:

Make the wires as short as possible.
Make power VCC, VCCQ and GND thick wires.
Try to add resistors R1, R2 as in the figure that we sent you in PM.
Bus width must be BUS MODE: 1bit.
You can try to raise the voltage but no more VOLTAGE: 2.2V.
You can try to lower the frequency below BUS SPEED: 10 MHz.

momo22 · 09-26-2021, 04:21

Quote:

Originally Posted by Medusa Box

Hello.

Check if the connections are correct:

Make the wires as short as possible.
Make power VCC, VCCQ and GND thick wires.
Try to add resistors R1, R2 as in the figure that we sent you in PM.
Bus width must be BUS MODE: 1bit.
You can try to raise the voltage but no more VOLTAGE: 2.2V.
You can try to lower the frequency below BUS SPEED: 10 MHz.

Please send to me resistors R1 R2 to me

Medusa Box · 09-27-2021, 07:59

Hello.

150 ohm resistors can be purchased here.

Install them as show the pic:

Or:

01-24-2021, 16:14	#2 (permalink)
andrei_d1978 Freak Poster Join Date: Aug 2010 Location: Russia,Yekaterinburg Posts: 102 Member: 1363017 Status: Offline Thanks Meter: 44	Do you supply power via vcc and vccq? The photo is poorly visible

01-24-2021, 16:37	#3 (permalink)
Master-ZizO Freak Poster Join Date: Sep 2012 Location: Egypt Age: 30 Posts: 164 Member: 1815000 Status: Offline Thanks Meter: 54	yes vcc and vccq connected to adapter .. same connection success with UFI

01-31-2021, 20:07	#4 (permalink)
Master-ZizO Freak Poster Join Date: Sep 2012 Location: Egypt Age: 30 Posts: 164 Member: 1815000 Status: Offline Thanks Meter: 54	I'm new to Medusa stuff .. i just bought it 2 weaks ago!

02-01-2021, 10:26	#5 (permalink)
Medusa Box Product Supporter Join Date: Mar 2011 Location: Octopus-team Posts: 9,360 Member: 1538383 Status: Offline Sonork: 100.1587278 Thanks Meter: 3,398	Hello. Check if the connections are correct: Make the wires as short as possible. Make power VCC, VCCQ and GND thick wires. Try to add resistors R1, R2 as in the figure that we sent you in PM. Bus width must be BUS MODE: 1bit. You can try to raise the voltage but no more VOLTAGE: 2.2V. You can try to lower the frequency below BUS SPEED: 10 MHz.