Can't init device. Reason: CMD Timeout Error - GSM-Forum

THE SLUTE · 10-16-2018, 07:07

eMMC_tool Suite ver. 1.5.2.0 (release date: 06.08.2018)
Microsoft Windows 7 (64 bit) build 7600 (6.1.7600.16385)

Looking for EasyJTAG box...
EasyJTAG API ver. 2100
EasyJTAG Box Serial = 88888888888888
Card Serial =77777777
EasyJTAG Box Firmware = 2.30

Changelog:

06.08.2018 (ver 1.5.2.0)
Fix: Bugs that have been found through your crash report
Fix: Writing ROM2 for Samsung (Write by vendor)
Fix: Freezing the program on a RandomVerify
Add: Folder for saving to Explorer (in settings)
Add: Extract from store.vol from emmc (explorer)
Add: Automatic repair of damaged store.vol when extracting (Explorer)
Add: Adding MountPoints for partitions (efs, userdata) when formatting
Add: Checking for an empty EFS before backup (Read by Vendor Samsung)

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 24 Mhz
CMD Pullup Level: 63 mV
CMD Active Level: 119 mV
Can't init device. Reason: CMD Timeout Error

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 Mhz
CMD Pullup Level: 68 mV
CMD Active Level: 224 mV
Can't init device. Reason: CMD Timeout Error

layder · 10-16-2018, 09:29

You have low signal level at CMD line. Check CMD line connection, power voltage, try to use hipower CLK mode (power to board via USB)

THE SLUTE · 10-16-2018, 10:11

Every things are fine, this error too much bother me.
Other emmc tool connected this without any error.

layder · 10-16-2018, 10:31

Quote:

Originally Posted by THE SLUTE

Every things are fine, this error too much bother me.
Other emmc tool connected this without any error.

New box hardware is needed to change something. We work to emproove connect stabilitity.

@ndoy · 10-19-2018, 06:52

Loading eMMC Addon Firmware... IO: 2800 mV
CMD Pullup Level:2062 mV
CMD Active Level:2475 mV
Box IO Level:2800 mV
CLK Rate:7000 khz
HiPower mode is off!
Can't init device, Reason: CMD Timeout Error
Done.

10-16-2018, 07:07	#1 (permalink)
THE SLUTE Registered User Join Date: Nov 2013 Location: Somewhere Posts: 129 Member: 2072293 Status: Offline Thanks Meter: 9	Can't init device. Reason: CMD Timeout Error eMMC_tool Suite ver. 1.5.2.0 (release date: 06.08.2018) Microsoft Windows 7 (64 bit) build 7600 (6.1.7600.16385) Looking for EasyJTAG box... EasyJTAG API ver. 2100 EasyJTAG Box Serial = 88888888888888 Card Serial =77777777 EasyJTAG Box Firmware = 2.30 Changelog: 06.08.2018 (ver 1.5.2.0) Fix: Bugs that have been found through your crash report Fix: Writing ROM2 for Samsung (Write by vendor) Fix: Freezing the program on a RandomVerify Add: Folder for saving to Explorer (in settings) Add: Extract from store.vol from emmc (explorer) Add: Automatic repair of damaged store.vol when extracting (Explorer) Add: Adding MountPoints for partitions (efs, userdata) when formatting Add: Checking for an empty EFS before backup (Read by Vendor Samsung) Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 24 Mhz CMD Pullup Level: 63 mV CMD Active Level: 119 mV Can't init device. Reason: CMD Timeout Error Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 36 Mhz CMD Pullup Level: 68 mV CMD Active Level: 224 mV Can't init device. Reason: CMD Timeout Error

10-19-2018, 06:52	#5 (permalink)
@ndoy Freak Poster Join Date: Apr 2010 Posts: 238 Member: 1280685 Status: Offline Thanks Meter: 59	Can't init device, Reason: CMD Timeout Error Loading eMMC Addon Firmware... IO: 2800 mV CMD Pullup Level:2062 mV CMD Active Level:2475 mV Box IO Level:2800 mV CLK Rate:7000 khz HiPower mode is off! Can't init device, Reason: CMD Timeout Error Done.

10-16-2018, 09:29	#2 (permalink)
layder Product Supporter Join Date: Jun 2002 Location: Belarus Age: 47 Posts: 3,188 Member: 13148 Status: Offline Thanks Meter: 2,948	You have low signal level at CMD line. Check CMD line connection, power voltage, try to use hipower CLK mode (power to board via USB)

10-16-2018, 10:11	#3 (permalink)
THE SLUTE Registered User Join Date: Nov 2013 Location: Somewhere Posts: 129 Member: 2072293 Status: Offline Thanks Meter: 9	Every things are fine, this error too much bother me. Other emmc tool connected this without any error.