i need Dump TaB P5220 - GSM-Forum

Dr.Dekra · 01-26-2017, 13:29

AFTER CHANGE A BAD EMMC
AND WRITE GP1 AND BOOT1 .2 AND ROM1 ;;;

Code:

CMD Pullup Level:1784 mV
CMD Active Level:1866 mV
Box IO Level:1800 mV
CLK Rate:21000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 15010056335730304D0034A34C455124
EMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2014  Rev.0x0
EMMC NAME: V3W00M , S/N:  883117125
EMMC NAME (HEX): 56335730304D00 
EMMC ROM1 (Main User Data)   Capacity: 14948 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
  Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
 Device support partitioning feature
 Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x01
EMMC GP0 (Extended Partition 1) Capacity: 40MB
---------------------------------------------
Backup saved: V3W00M_ 883117125_20170125_1326.extcsd
Searching for partition tables...
Detected GPT over MBR...
Warning: Header Size = 512 (expected 92)
Medium UUID: 52444E41-494F-2044-4D4D-43204449534B
Warning: Entries Count = 128
MMCBLK0P0 (RESERVED1) Range: [0X2800000,0X2AFFE00] ,Len: 300000
MMCBLK0P1 (EFS) Range: [0X800000,0X1BFFE00] ,Len: 1400000
MMCBLK0P2 (CONFIG) Range: [0X7000000,0X7FFFE00] ,Len: 1000000
MMCBLK0P3 (FACTORY) Range: [0X8000000,0X81FFE00] ,Len: 200000
MMCBLK0P4 (MEDIA) Range: [0X8200000,0X83FFE00] ,Len: 200000
MMCBLK0P5 (CACHE) Range: [0XA3800000,0XB95FFE00] ,Len: 15E00000
MMCBLK0P6 (RESERVED2) Range: [0X8400000,0X87FFE00] ,Len: 400000
MMCBLK0P7 (SYSTEM) Range: [0X9C00000,0X9D3FFE00] ,Len: 93800000
MMCBLK0P8 (USERDATA) Range: [0XB9600000,0X3AA9FFE00] ,Len: 2F1400000
MMCBLK0P9 (BOOT) Range: [0X3400000,0X47FFE00] ,Len: 1400000
MMCBLK0P10 (RECOVERY) Range: [0X4800000,0X5BFFE00] ,Len: 1400000
MMCBLK0P11 (RADIO) Range: [0X5C00000,0X6FFFE00] ,Len: 1400000
MMCBLK0P12 (HIDDEN) Range: [0X9D400000,0XA37FFE00] ,Len: 6400000
MMCBLK0P13 (CARRIER) Range: [0X8800000,0X8BFFE00] ,Len: 400000
MMCBLK0P14 (TDATA) Range: [0X8C00000,0X8FFFE00] ,Len: 400000
MMCBLK0P15 (PARAM) Range: [0X2400000,0X27FFE00] ,Len: 400000
MMCBLK0P16 (PERSDATA) Range: [0X9000000,0X9BFFE00] ,Len: C00000
MMCBLK0P17 (BOTA0) Range: [0X400000,0X5FFE00] ,Len: 200000
MMCBLK0P18 (BOTA1) Range: [0X600000,0X7FFE00] ,Len: 200000
MMCBLK0P19 (DNX) Range: [0X2B00000,0X2BFFE00] ,Len: 100000
MMCBLK0P20 (OTA) Range: [0X2C00000,0X33FFE00] ,Len: 800000
Done...Presets has been updated...

THE P5200 DUMP ;;; REVIVE THE P5220 BUT JUST RECOVERY MODE...WITH ERROR WIPE !( 0MB SIZE) AND PROBLEM WITH ODIN, NOTHING PASSE ;; NO PIT NO BOOT ... ETC ;

Dr.Dekra · 01-28-2017, 11:14

No one can share this dump ?

BABAK NURI · 01-28-2017, 12:10

Hi
Why you need dump when you can use easy jtag plus ?
Just write latest FW

Dr.Dekra · 01-28-2017, 20:24

Quote:

Originally Posted by BABAK NURI

Hi
Why you need dump when you can use easy jtag plus ?
Just write latest FW

whene i use latest sw easy jtag plus the tab just dead ==> (cloverview)
I THINK because i use gpt1 file from p5200 !!
EMMC GP0 (Extended Partition 1) Capacity: 40MB

i use a new emmc from samsung s4 ; i think 40MB is correct
========
i change just a pit PART (0X0004400 TO 0X0005307) from p5200 DUMP and now partition its ok ... i can access to recovery mode and write system boot recovery BY ODIN .... but i cant write sboot,pit.
+ i TRY TO write sboot by direct at address: hex 0x0006480
BUT ITS KILL THE TAB (cloverview)
+i try to write iafw.bin to boot1 ; 2 .... the tab dead ===>(cloverview)
===========
I NEED THIS DUMP OR ANY SOLUTION TO REVIVE THIS TAB

BABAK NURI · 01-29-2017, 09:16

Hi
No need write manually
Are you sure you have P5220? can you check pcb for exactly model?
because if you have P5220 then write latest BL-pit(P5220) tab must be turn on not dead

Dr.Dekra · 01-29-2017, 12:41

Yes i use p5220xxubnh2 4.4.2 version

BABAK NURI · 01-29-2017, 19:27

Hi
ok,try this manual
if you have P5200 as product model in Downloading
Just remove any Bootloader parts from P5220 FW Then Write By Odin
i mean just write System/csc/recovery/boot,etc

Dr.Dekra · 01-29-2017, 20:05

Quote:

hipower mode is on
cmd pullup level: 2186 mv
cmd active level: 2516 mv
emmc device information :
Emmc cid: 15010056335730304d0034a34c455124
emmc csd: D02701320f5903fff6dbffef8e40400c
emmc manufacture name: Samsung
emmc name: V3w00m , s/n: 34a34c45 , rev. 00
emmc name (hex): 56335730304d
emmc rom 1 (main user data) capacity: 15028 mb (0003ab400000)
emmc rom 2/3 (boot partition 1/2) capacity: 4096 kb (000000400000)
emmc rpmb (replay protected memory block) capacity: 512 kb (000000080000)
backup saved: V3w00m_34a34c45_20170129_195332.extcsd
emmc init completed.

Opening file: Gt-p5220_eur_xx_20130523.pit

pit: Gt-p5220_eur_xx_20130523.pit
entry count: 27

the size of the last section has been updated

p5220xxuboa2_p5220oxxbob1_p5220xxubnk1_home.tar.md 5
the list of files in the firmware:
Sboot.bin
dnx_fwr.bin
iafw.bin
boot.img
recovery.img
system.img
modem.bin
cache.img
hidden.img

hipower mode is on
cmd pullup level: 2175 mv
cmd active level: 2505 mv
emmc device information :
Emmc cid: 15010056335730304d0034a34c455124
emmc csd: D02701320f5903fff6dbffef8e40400c
emmc manufacture name: Samsung
emmc name: V3w00m , s/n: 34a34c45 , rev. 00
emmc name (hex): 56335730304d
emmc rom 1 (main user data) capacity: 15028 mb (0003ab400000)
emmc rom 2/3 (boot partition 1/2) capacity: 4096 kb (000000400000)
emmc rpmb (replay protected memory block) capacity: 512 kb (000000080000)
backup saved: V3w00m_34a34c45_20170129_195357.extcsd
emmc init completed.

Creating gpt-partitioninig
writing pit at address: 000000004400
gpt-partitioning done

unpacking file: Iafw.bin
unpacking file: Sboot.bin
unpacking file: Dnx_fwr.bin
unpacking file: Boot.img
unpacking file: Recovery.img
unpacking file: Modem.bin

partition name: Iafw
filename: Iafw.bin , offset: 000000000000 , filesize: 2096388 bytes
emmc switching to rom2
erasing partition...
Writing partition...
Done writing partition. Write speed: 316,49 kb/s
partition name: Sboot
filename: Sboot.bin , offset: 000000006200 , filesize: 1441792 bytes
emmc switching to rom1
erasing partition...
Writing partition...
Done writing partition. Write speed: 705,75 kb/s
partition name: Dnx
filename: Dnx_fwr.bin , offset: 000002b00000 , filesize: 99296 bytes
emmc switching to rom1
erasing partition...
Writing partition...
Done writing partition. Write speed: 321,15 kb/s
partition name: Boot
filename: Boot.img , offset: 000003400000 , filesize: 7201024 bytes
emmc switching to rom1
erasing partition...
Writing partition...
Done writing partition. Write speed: 441,93 kb/s
partition name: Recovery
filename: Recovery.img , offset: 000004800000 , filesize: 10053888 bytes
emmc switching to rom1
erasing partition...
Writing partition...
Done writing partition. Write speed: 441,87 kb/s
partition name: Radio
filename: Modem.bin , offset: 000005c00000 , filesize: 28600832 bytes
emmc switching to rom1
erasing partition...
Writing partition...
Done writing partition. Write speed: 628,19 kb/s

all done

2nd flash tab dead
============
in download mode nothing displayed just vertical line , but in recovery mode , display ok and keys ok
===========
my tab is p5220 g4 100%
i i check this solution sir , but after flash done the tab reboot to recovery with red error , after wipe ;;; no error ;;; reboot and just freezing with vertical lines ,,,
==========
i think the problem in gp1 partition file. (8mb MUST for p5220)

Dr.Dekra · 01-29-2017, 20:21

Quote:

Originally Posted by babak nuri

hi
ok,try this manual
if you have p5200 as product model in downloading
just remove any bootloader parts from p5220 fw then write by odin
i mean just write system/csc/recovery/boot,etc

in odin pass just system and boot and recovery;.
No csc because pit insid. Cant pass ;;; error odin

oamranish · 01-19-2018, 15:55

GT-P5220 emmc pinout please. Its completely dead after i flash vioa octopus.

01-28-2017, 11:14	#2 (permalink)
Dr.Dekra Freak Poster Join Date: Feb 2009 Posts: 151 Member: 961313 Status: Offline Sonork: 100.1625300 Thanks Meter: 35	No one can share this dump ?

01-28-2017, 12:10	#3 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	Hi Why you need dump when you can use easy jtag plus ? Just write latest FW

01-29-2017, 09:16	#5 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	Hi No need write manually Are you sure you have P5220? can you check pcb for exactly model? because if you have P5220 then write latest BL-pit(P5220) tab must be turn on not dead

01-29-2017, 12:41	#6 (permalink)
Dr.Dekra Freak Poster Join Date: Feb 2009 Posts: 151 Member: 961313 Status: Offline Sonork: 100.1625300 Thanks Meter: 35	Yes i use p5220xxubnh2 4.4.2 version

01-29-2017, 19:27	#7 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	Hi ok,try this manual if you have P5200 as product model in Downloading Just remove any Bootloader parts from P5220 FW Then Write By Odin i mean just write System/csc/recovery/boot,etc

01-19-2018, 15:55	#10 (permalink)
oamranish Junior Member Join Date: Dec 2015 Posts: 19 Member: 2497086 Status: Offline Sonork: [email protected] Thanks Meter: 2	GT-P5220 emmc pinout please. Its completely dead after i flash vioa octopus.