motorola xt1022 qualco drivers only detected

[umarmsn]

is it possible to repaire?


if yes

need procedure

[reset12345]

Originally Posted by umarmsn

is it possible to repaire?


if yes

need procedure

[CENTER]

World's 1st MOTO E XT1022 eMMC Repair with Guide for all GsmHosting[IMG]

[/COLOR][/B][/B][/SIZE]
[U]So many Peoples waiting this solution. I give Surprise to our Family[IMG]

Follow Step by Step:

1.Download Rom files (Extract to in your PC)and Pinout image,

2.Solder Pinout carefully on board and eMMC adopter and insert adopter in easy jtag box,

3.Open Easy jtag tool goto eMMC Tool section,

4.Press Detect eMMC Card after detect eMMC Tick all eMMC Regions at once,

5.Select Rom1 where are Extract Rom files,

6.When select Rom1 easy jtag was auto select all roms,

7.After select roms Press Write all ROMs,

8.After write roms disconnect board from adopter and normally flash your mobile with tool or cmd process.[IMG




Rom Files Download Here: MOTO XT1022 ROMS

[reset12345]

here is pin out

all pinout try this.................

[ribut budiono]

can you share with me dump file

[reset12345]

Originally Posted by ribut budiono

can you share with me dump file

Moto-E System Dump Here

CLICK ME

[daman_dut]

This Solution Not Working...

[daman_dut]

Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: , ,FW Ver.: 01.55
CMD Pullup Level:2010 mV
CMD Active Level:2444 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower mode is off!
---------- eMMC Device Information ----------

EMMC CID : 90014A4834473164040503A1CC07519C

EMMC CSD : D02701320F5903FFFFFFFFEF8A4040D2

EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 05/2014 Rev.0x5
EMMC NAME: <b>H4G1d </b> , S/N: 60935175
EMMC NAME (HEX): 48344731642000
EMMC ROM1 (Main User Data) Capacity: 3728 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x38] Boot from:ROM1 (Main User Area)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x38.
H/W reset function [RST_N_FUNCTION]: 0x01

High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]

Partitioning Support [PARTITIONING_SUPPORT]: 0x07

Device support partitioning feature

Device can have enhanced tech.

Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00

---------------------------------------------

Backup saved: H4G1d _ 60935175_20160806_1303.extcsd
Done.

Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.3.0.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2010 mV
CMD Active Level:2444 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
Writing...
Done.

Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 953 kB/s

Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 1386 kB/s

Writing 0000200000 bytes to 00000000 ...ROM3 (BOOT2 ROM)
Done. Write Speed: 1399 kB/s

[ribut budiono]

yes not working .phone stiil dead boot

[umarmsn]

Originally Posted by ribut budiono

yes not working .phone stiil dead boot

Yes this procedure does not work


Pls give me solution of moto xt1022

[comsi]

sucess full repair Boot write !

BUT still DEAD !

Plz help z3x team this solution not working properly !!!!

[hm.faizan]

u can write stock firmware via easy jtag Direct eMMC Qualcomm Flasher

[umarmsn]

Originally Posted by hm.faizan

u can write stock firmware via easy jtag Direct eMMC Qualcomm Flasher

Can I share procedure of process?

[Gsmbizz]

Originally Posted by umarmsn

Can I share procedure of process?

try use Direct eMMC Qualcomm Flasher

[comsi]

Originally Posted by Cute_Shibu

try use Direct eMMC Qualcomm Flasher

please tell the steps how to do. and whicj flash file?

[comsi]

Originally Posted by hm.faizan

u can write stock firmware via easy jtag Direct eMMC Qualcomm Flasher

plz tell me steps. how to do this

XT1022_Retail_DualSim_51_Stock_Untouched.zip

in software it asks XML file