vivo y95 Universal Factory Format error - GSM-Forum

.::AZEEM::. · 08-07-2020, 14:13

halo product supporter im get one vivo phone helth report is bad when i try to repair getting error

Info

Quote:

EMMC Device Information :
EMMC CID: 90014A484347386134A24BAAC6591665
EMMC CSD: D02701328F5903FFFFFFFFEF8A400027
EMMC Manufacture : SKHYNIX , EMMC NAME: HCG8a4 , HEX: 484347386134 , S/N: 4BAAC659 , rev. 0xA2
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2019
EMMC ROM 1 (Main User Data) Capacity: 59640 MB (000E8F800000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: HCG8a4_4BAAC659_20200807_183623.extcsd
EMMC Init completed.

Warning: BusWidth is automatically set to 1 Bit

Warning: Health report is very BAD

Device Life Time Estimation (MLC) [269]: 0x02 10% - 20% device life time used
Device Life Time Estimation (SLC) [268]: 0x01 0% - 10% device life time used
Pre EOL information [267]: 0x03 Urgent

Scanning soft partitions
GPT header is found and is valid
Partition: modem, [000001000000 - 000009000000], size: 000008000000 (128. MB)
Partition: fsc, [000009000000 - 000009000400], size: 000000000400 (1.00 KB)
Partition: ssd, [000009001000 - 000009003000], size: 000000002000 (8.00 KB)
Partition: sbl1, [000009003000 - 000009083000], size: 000000080000 (512. KB)
Partition: sbl1bak, [000009083000 - 000009103000], size: 000000080000 (512. KB)
Partition: rpm, [000009103000 - 000009183000], size: 000000080000 (512. KB)
Partition: rpmbak, [000009183000 - 000009203000], size: 000000080000 (512. KB)
Partition: tz, [000009203000 - 000009403000], size: 000000200000 (2.00 MB)
Partition: tzbak, [000009403000 - 000009603000], size: 000000200000 (2.00 MB)
Partition: devcfg, [000009603000 - 000009643000], size: 000000040000 (256. KB)
Partition: devcfgbak, [000009643000 - 000009683000], size: 000000040000 (256. KB)
Partition: dsp, [000009683000 - 00000A683000], size: 000001000000 (16.0 MB)
Partition: dspbak, [00000A683000 - 00000B683000], size: 000001000000 (16.0 MB)
Partition: modemst1, [00000B683000 - 00000B903000], size: 000000280000 (2.50 MB)
Partition: modemst2, [00000B903000 - 00000BB83000], size: 000000280000 (2.50 MB)
Partition: DDR, [00000C000000 - 00000C008000], size: 000000008000 (32.0 KB)
Partition: fsg, [00000C008000 - 00000C288000], size: 000000280000 (2.50 MB)
Partition: sec, [00000C288000 - 00000C28C000], size: 000000004000 (16.0 KB)
Partition: splash, [00000D000000 - 00000DB00000], size: 000000B00000 (11.0 MB)
Partition: aboot, [00000E000000 - 00000F000000], size: 000001000000 (16.0 MB)
Partition: abootbak, [00000F000000 - 000010000000], size: 000001000000 (16.0 MB)
Partition: dtbo, [000010000000 - 000010800000], size: 000000800000 (8.00 MB)
Partition: dtbobak, [000010800000 - 000011000000], size: 000000800000 (8.00 MB)
Partition: vbmeta, [000011000000 - 000011010000], size: 000000010000 (64.0 KB)
Partition: vbmetabak, [000011010000 - 000011020000], size: 000000010000 (64.0 KB)
Partition: boot, [000011020000 - 000015020000], size: 000004000000 (64.0 MB)
Partition: recovery, [000015020000 - 000019020000], size: 000004000000 (64.0 MB)
Partition: devinfo, [000019020000 - 00001A020000], size: 000001000000 (16.0 MB)
Partition: system, [00001A020000 - 00013A020000], size: 000120000000 (4.50 GB)
Partition: vendor, [00013A020000 - 00018A020000], size: 000050000000 (1.25 GB)
Partition: cache, [00018B000000 - 00019B000000], size: 000010000000 (256. MB)
Partition: persist, [00019B000000 - 00019D000000], size: 000002000000 (32.0 MB)
Partition: misc, [00019D000000 - 00019D100000], size: 000000100000 (1.00 MB)
Partition: keystore, [00019D100000 - 00019D180000], size: 000000080000 (512. KB)
Partition: config, [00019D180000 - 00019D188000], size: 000000008000 (32.0 KB)
Partition: oem, [00019D188000 - 0001A1188000], size: 000004000000 (64.0 MB)
Partition: limits, [0001A2000000 - 0001A2008000], size: 000000008000 (32.0 KB)
Partition: mota, [0001A3000000 - 0001A3080000], size: 000000080000 (512. KB)
Partition: dip, [0001A3080000 - 0001A3180000], size: 000000100000 (1.00 MB)
Partition: mdtp, [0001A3180000 - 0001A5180000], size: 000002000000 (32.0 MB)
Partition: mdtpbak, [0001A5180000 - 0001A7180000], size: 000002000000 (32.0 MB)
Partition: syscfg, [0001A7180000 - 0001A7200000], size: 000000080000 (512. KB)
Partition: mcfg, [0001A7200000 - 0001A7600000], size: 000000400000 (4.00 MB)
Partition: cmnlib, [0001A8000000 - 0001A8100000], size: 000000100000 (1.00 MB)
Partition: cmnlibbak, [0001A8100000 - 0001A8200000], size: 000000100000 (1.00 MB)
Partition: cmnlib64, [0001A8200000 - 0001A8300000], size: 000000100000 (1.00 MB)
Partition: cmnlib64bak, [0001A8300000 - 0001A8400000], size: 000000100000 (1.00 MB)
Partition: keymaster, [0001A8400000 - 0001A8500000], size: 000000100000 (1.00 MB)
Partition: keymasterbak, [0001A8500000 - 0001A8600000], size: 000000100000 (1.00 MB)
Partition: survival, [0001A8600000 - 0001AC600000], size: 000004000000 (64.0 MB)
Partition: apdp, [0001AD000000 - 0001AD040000], size: 000000040000 (256. KB)
Partition: msadp, [0001AD040000 - 0001AD080000], size: 000000040000 (256. KB)
Partition: dpo, [0001AD080000 - 0001AD082000], size: 000000002000 (8.00 KB)
Partition: logdump, [0001AD082000 - 0001B1082000], size: 000004000000 (64.0 MB)
Partition: apanic, [0001B1082000 - 0001B1A82000], size: 000000A00000 (10.0 MB)
Partition: backup, [0001B1A82000 - 0001B2482000], size: 000000A00000 (10.0 MB)
Partition: seed, [0001B2482000 - 0001B2882000], size: 000000400000 (4.00 MB)
Partition: reserved, [0001B2882000 - 0001B3282000], size: 000000A00000 (10.0 MB)
Partition: userdata, [0001B3282000 - 000E8F7FBE00], size: 000CDC579E00 (51.4 GB)
GPT header successfully parsed

Get firmware version

Brand = vivo
Manufacturer = vivo
Device = msm8937_64
Model = vivo 1807
CPU Abi = arm64-v8a
Android release = 8.1.0
Firmware version = OPM1.171019.026 release-keys
Firmware date = Mon Mar 4 22:02:05 CST 2019

S.M.A.R.T report

Quote:

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 18 MHz
CMD Pullup Level: 1 mV
CMD Active Level: 0 mV
EMMC Device Information :
EMMC CID: 90014A484347386134A24BAAC6591665
EMMC CSD: D02701328F5903FFFFFFFFEF8A400027
EMMC Manufacture : SKHYNIX , EMMC NAME: HCG8a4 , HEX: 484347386134 , S/N: 4BAAC659 , rev. 0xA2
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2019
EMMC ROM 1 (Main User Data) Capacity: 59640 MB (000E8F800000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 443575 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: HCG8a4_4BAAC659_20200807_184136.extcsd
EMMC Init completed.

Operation: Reading S.M.A.R.T Report ...

Device Life Time Estimation (MLC) [269]: 0x02 10% - 20% device life time used
Device Life Time Estimation (SLC) [268]: 0x01 0% - 10% device life time used
Pre EOL information [267]: 0x03 Urgent

Optimal Read Size [266]: 0x40 256 KB
Optimal Write Size [265]: 0x40 256 KB
Optimal Trim Unit Size [264]: 0x07 28 KB

Operation: Universal Factory Format

Quote:

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 18 MHz
CMD Pullup Level: 1 mV
CMD Active Level: 0 mV
EMMC Device Information :
EMMC CID: 90014A484347386134A24BAAC6591665
EMMC CSD: D02701328F5903FFFFFFFFEF8A400027
EMMC Manufacture : SKHYNIX , EMMC NAME: HCG8a4 , HEX: 484347386134 , S/N: 4BAAC659 , rev. 0xA2
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2019
EMMC ROM 1 (Main User Data) Capacity: 59640 MB (000E8F800000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 443575 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: HCG8a4_4BAAC659_20200807_183634.extcsd
EMMC Init completed.

Warning: Health report is very BAD

Device Life Time Estimation (MLC) [269]: 0x02 10% - 20% device life time used
Device Life Time Estimation (SLC) [268]: 0x01 0% - 10% device life time used
Pre EOL information [267]: 0x03 Urgent

Operation: Universal Factory Format
Please, wait ...
Error: 144 Unknown error

Final write

Quote:

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 18 MHz
CMD Pullup Level: 1 mV
CMD Active Level: 0 mV
EMMC Device Information :
EMMC CID: 90014A484347386134A24BAAC6591665
EMMC CSD: D02701328F5903FFFFFFFFEF8A400027
EMMC Manufacture : SKHYNIX , EMMC NAME: HCG8a4 , HEX: 484347386134 , S/N: 4BAAC659 , rev. 0xA2
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 1/2019
EMMC ROM 1 (Main User Data) Capacity: 59640 MB (000E8F800000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 443575 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: HCG8a4_4BAAC659_20200807_184039.extcsd
EMMC Init completed.

Warning: Health report is very BAD

Device Life Time Estimation (MLC) [269]: 0x02 10% - 20% device life time used
Device Life Time Estimation (SLC) [268]: 0x01 0% - 10% device life time used
Pre EOL information [267]: 0x03 Urgent

Operation: Changing GP sizes (final write) ...

GP1 size: 0 MB , WR_REL: 1 , ENH 1
GP2 size: 0 MB , WR_REL: 1 , ENH 1
GP3 size: 0 MB , WR_REL: 1 , ENH 1
GP4 size: 0 MB , WR_REL: 1 , ENH 1

Zero sizes. This may damage your eMMC
Do you want to continue?

HW_PART error. Reason: CMD Timeout Error

need help

engcobocell · 08-07-2020, 19:22

Open Easy jteg tool Detect emmc i hope you will see problem

Press the thanks button please

Sent from my SM-A520F using Tapatalk

.::AZEEM::. · 08-08-2020, 04:50

Quote:

Originally Posted by engcobocell

Open Easy jteg tool Detect emmc i hope you will see problem

Press the thanks button please

Sent from my SM-A520F using Tapatalk

Sry I'm not understand ur words can u tell me clean

.::BIG BOSS::. · 08-19-2021, 16:11

Quote:

Originally Posted by .::AZEEM::.

Sry I'm not understand ur words can u tell me clean

cheng voltage 2.8 working

08-07-2020, 19:22	#2 (permalink)
engcobocell No Life Poster Join Date: Jun 2016 Location: every ware in your hart Posts: 798 Member: 2590583 Status: Offline Thanks Meter: 198	Open Easy jteg tool Detect emmc i hope you will see problem Press the thanks button please Sent from my SM-A520F using Tapatalk