E10i only vibrate ... - GSM-Forum

services_mobile · 09-01-2012, 14:07

Phone is dead but when power on ,only vibrate ...
How to fix this ?

Octopus box · 09-03-2012, 07:26

Hello.
Have You tried to re-flash the phone? Also if this will not help - You can repair this phone using Medusa Box.

services_mobile · 09-03-2012, 09:56

Yes ,i repaired with Medusa Box and i re-flashed with Octopus Suite .
But with no results ...

Octopus box · 09-03-2012, 10:00

Please post here full software logs with Repair and Write firmware procedures.

services_mobile · 09-03-2012, 15:54

Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision B.
Detected TAP ID: 203C00E1, IR Length = 4.
JTAG speed : Auto (RTCK).
VREF level : 2.63 V
CPU : Qualcomm MSM7227
Core ID : 203C00E1
Flash device: ST Micro 512Mb
Flash ID : 002055BC
Page size : 2048 bytes
Block size : 64 pages (128 Kb)
Block count: 4096
Flash size : 512 Mb
Write protection disabled.
Reading TA section. Please wait... Done
TA section has been backed up to
"c:\Program Files\GsmServer\Medusa\Firmware\Sony Ericsson E10i TA Backup 02-09-2012 08_17_13.mf".
Erasing TA section. Please wait... Done
Repairing. Please wait... Done
Disconnected
Repair done.

--------------------------------------------------------------------

Welcome to Medusa Box Flasher version 1.1.0

Platform: SE Qualcomm
Selected model: E10i
Opening "E10i_2.1.1.A.0.6_CUST_BAL_WORLD.oct"...OK
Please, reconnect battery, hold "back" key and connect USB cable...OK
Reading info...
Chipset: S1 MSM7227
IMEI: xxxxxx-xx-xxxxxx-x
MSN: BX902BT4AW
Sending loader...OK
Writing Firmware...
Writing AMSS...OK
Writing AMSS_FS...OK
Writing CACHE...OK
Writing FOTA0...OK
Writing FOTA1...OK
Writing KERNEL...OK
Writing SYSTEM...OK
Writing USERDATA...OK
Shutting down...OK

Octopus box · 09-03-2012, 16:14

Please try to perform the following steps:
1. Connect the phone in Advanced Mode and make Erase Full flash.
2. Connect the phone in EasyRepair Mode and make Repair.
3. Re-flash the phone again.

P.S. Don't forget to fully charge phone's battery before (at least to 4.2V.)!

services_mobile · 09-04-2012, 14:55

Selected device model: Sony Ericsson E10i
Connecting. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision B.
Detected TAP ID: 203C00E1, IR Length = 4.
JTAG speed : Auto (RTCK).
VREF level : 2.65 V
CPU : Qualcomm MSM7227
Core ID : 203C00E1
Flash device: ST Micro 512Mb
Flash ID : 002055BC
Page size : 2048 bytes
Block size : 64 pages (128 Kb)
Block count: 4096
Flash size : 512 Mb
Write protection disabled.
Connect successful.
ECC Mode enabled.
Erasing BOOT section. Please wait... Done
Erasing FIRMWARE section. Please wait... Done

-------------------------------------------------------------------------------------------------
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision B.
Detected TAP ID: 203C00E1, IR Length = 4.
JTAG speed : Auto (RTCK).
VREF level : 2.63 V
CPU : Qualcomm MSM7227
Core ID : 203C00E1
Flash device: ST Micro 512Mb
Flash ID : 002055BC
Page size : 2048 bytes
Block size : 64 pages (128 Kb)
Block count: 4096
Flash size : 512 Mb
Write protection disabled.
Reading TA section. Please wait... Done
TA section has been backed up to
"c:\Program Files\GsmServer\Medusa\Firmware\Sony Ericsson E10i TA Backup 04-09-2012 13_20_44.mf".
Erasing TA section. Please wait... Done
Repairing. Please wait... Done
Disconnected
Repair done.
--------------------------------------------------------------------------------------------------
Welcome to Medusa Box Flasher version 1.1.0
Platform: SE Qualcomm
Selected model: E10i
Opening "E10i_1.2.A.1.174_MOVILNET_VE.oct"...OK
Please, reconnect battery, hold "back" key and connect USB cable...OK
Reading info...
Chipset: S1 MSM7227
IMEI: xxxxxx-xx-xxxxxx-x
MSN: BX902BT4AW
Sending loader...OK
Writing Firmware...
Writing AMSS...OK
Writing AMSS_FS...OK
Writing CACHE...OK
Writing FOTA0...OK
Writing FOTA1...OK
Writing KERNEL...OK
Writing SYSTEM...OK
Writing USERDATA...OK
Shutting down...OK
---------------------------------------------------------------------------------------------------
I tried and it does not work ...
BTW ,Where can I find full flash for this model E10i ?

Octopus box · 09-04-2012, 15:25

This can be HW problem.

09-01-2012, 14:07	#1 (permalink)
services_mobile No Life Poster Join Date: Jul 2006 Location: uk Posts: 596 Member: 306676 Status: Offline Thanks Meter: 148	E10i only vibrate ... Phone is dead but when power on ,only vibrate ... How to fix this ?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
5110/6110 after unlocking see only network to which it was locked and ...	2M	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	8	07-25-2000 00:51
Only MAX232 ???	AMIGO	Nokia Hardware & Hardware Repair	7	04-12-2000 09:41
only 1800Mhz ??	dofie	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	01-17-2000 21:51
£20 only NOKIA 51xx/61xx sp locks 1,2,3,4 removed	spterminator	Main Sales Section	0	08-08-1999 05:08
i can unlock nokia 51xx/61xx sp locks 1,2,3,4 £40 each £30 bulk for u.k only	spterminator	Main Sales Section	0	08-01-1999 05:46

09-03-2012, 07:26	#2 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,850 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,413	Hello. Have You tried to re-flash the phone? Also if this will not help - You can repair this phone using Medusa Box.

09-03-2012, 09:56	#3 (permalink)
services_mobile No Life Poster Join Date: Jul 2006 Location: uk Posts: 596 Member: 306676 Status: Offline Thanks Meter: 148	Yes ,i repaired with Medusa Box and i re-flashed with Octopus Suite . But with no results ...

09-03-2012, 10:00	#4 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,850 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,413	Please post here full software logs with Repair and Write firmware procedures.

09-03-2012, 15:54	#5 (permalink)
services_mobile No Life Poster Join Date: Jul 2006 Location: uk Posts: 596 Member: 306676 Status: Offline Thanks Meter: 148	Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision B. Detected TAP ID: 203C00E1, IR Length = 4. JTAG speed : Auto (RTCK). VREF level : 2.63 V CPU : Qualcomm MSM7227 Core ID : 203C00E1 Flash device: ST Micro 512Mb Flash ID : 002055BC Page size : 2048 bytes Block size : 64 pages (128 Kb) Block count: 4096 Flash size : 512 Mb Write protection disabled. Reading TA section. Please wait... Done TA section has been backed up to "c:\Program Files\GsmServer\Medusa\Firmware\Sony Ericsson E10i TA Backup 02-09-2012 08_17_13.mf". Erasing TA section. Please wait... Done Repairing. Please wait... Done Disconnected Repair done. -------------------------------------------------------------------- Welcome to Medusa Box Flasher version 1.1.0 Platform: SE Qualcomm Selected model: E10i Opening "E10i_2.1.1.A.0.6_CUST_BAL_WORLD.oct"...OK Please, reconnect battery, hold "back" key and connect USB cable...OK Reading info... Chipset: S1 MSM7227 IMEI: xxxxxx-xx-xxxxxx-x MSN: BX902BT4AW Sending loader...OK Writing Firmware... Writing AMSS...OK Writing AMSS_FS...OK Writing CACHE...OK Writing FOTA0...OK Writing FOTA1...OK Writing KERNEL...OK Writing SYSTEM...OK Writing USERDATA...OK Shutting down...OK

09-03-2012, 16:14	#6 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,850 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,413	Please try to perform the following steps: 1. Connect the phone in Advanced Mode and make Erase Full flash. 2. Connect the phone in EasyRepair Mode and make Repair. 3. Re-flash the phone again. P.S. Don't forget to fully charge phone's battery before (at least to 4.2V.)!

09-04-2012, 14:55	#7 (permalink)
services_mobile No Life Poster Join Date: Jul 2006 Location: uk Posts: 596 Member: 306676 Status: Offline Thanks Meter: 148	Selected device model: Sony Ericsson E10i Connecting. Please wait... Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision B. Detected TAP ID: 203C00E1, IR Length = 4. JTAG speed : Auto (RTCK). VREF level : 2.65 V CPU : Qualcomm MSM7227 Core ID : 203C00E1 Flash device: ST Micro 512Mb Flash ID : 002055BC Page size : 2048 bytes Block size : 64 pages (128 Kb) Block count: 4096 Flash size : 512 Mb Write protection disabled. Connect successful. ECC Mode enabled. Erasing BOOT section. Please wait... Done Erasing FIRMWARE section. Please wait... Done ------------------------------------------------------------------------------------------------- Medusa JTAG Firmware version 1.1.0. Medusa JTAG Hardware S64 revision B. Detected TAP ID: 203C00E1, IR Length = 4. JTAG speed : Auto (RTCK). VREF level : 2.63 V CPU : Qualcomm MSM7227 Core ID : 203C00E1 Flash device: ST Micro 512Mb Flash ID : 002055BC Page size : 2048 bytes Block size : 64 pages (128 Kb) Block count: 4096 Flash size : 512 Mb Write protection disabled. Reading TA section. Please wait... Done TA section has been backed up to "c:\Program Files\GsmServer\Medusa\Firmware\Sony Ericsson E10i TA Backup 04-09-2012 13_20_44.mf". Erasing TA section. Please wait... Done Repairing. Please wait... Done Disconnected Repair done. -------------------------------------------------------------------------------------------------- Welcome to Medusa Box Flasher version 1.1.0 Platform: SE Qualcomm Selected model: E10i Opening "E10i_1.2.A.1.174_MOVILNET_VE.oct"...OK Please, reconnect battery, hold "back" key and connect USB cable...OK Reading info... Chipset: S1 MSM7227 IMEI: xxxxxx-xx-xxxxxx-x MSN: BX902BT4AW Sending loader...OK Writing Firmware... Writing AMSS...OK Writing AMSS_FS...OK Writing CACHE...OK Writing FOTA0...OK Writing FOTA1...OK Writing KERNEL...OK Writing SYSTEM...OK Writing USERDATA...OK Shutting down...OK --------------------------------------------------------------------------------------------------- I tried and it does not work ... BTW ,Where can I find full flash for this model E10i ?

09-04-2012, 15:25	#8 (permalink)
Octopus box Product Supporter Join Date: Oct 2009 Location: Romania, Bucharest Posts: 99,850 Member: 1146942 Status: Offline Sonork: 100.1587278 Thanks Meter: 27,413	This can be HW problem.