Alcatel ot800 not done with cable - GSM-Forum

networker · 09-16-2012, 11:38

The phone does not boot, just goes on.
Through smart moto works without problems.
I use com1.

GSM_Support · 09-17-2012, 07:24

@ networker,

What cable exactly are you using?
Please specify step-by-step operation you perform.

Best Regards
GSMServer team

networker · 09-17-2012, 09:33

I am using com port cable from siemens with whom I have never had a problem in communication with the phone (as I have with profilic or ftdi).
SigmaKey 1:11:00
98797xxx Sigma dongle 1.14, Initializing ... OK
SigmaKey 1:11:00 MTK: Get unlock codes
Communications Port (COM1) Provider: Microsoft Driver ver.: 5.1.2600.0, Date: 07/01/2001
Baud rate: Autodetect
Press and HOLD "Power on" button ... _

When I press Power on, the phone is turned on and the software does not show any error.
The same procedure with SmartMoto goes out first.
Greeting

mcandre · 09-17-2012, 09:38

Did you made any changes into "DTR&RTS settings" in sigmakey (options tab)?

networker · 09-18-2012, 13:00

NO, I did not. I will try when I have another phone.

mcandre · 09-18-2012, 15:35

networker, what cable do you use, exactly?
In case you are using USB cable, just select correct COM-Port in the Serial Port settings.

If you use physical COM port cable, just make the next settings in "DTR&RTS control":
DTR=ON RTS=ON

networker · 09-18-2012, 15:38

I swich DTR&RTS settings to SigmaBox (IGNITION)

SigmaKey 1.12.00
987979xxx Sigma dongle 1.15, Initializing...OK
SigmaKey 1.12.00 MTK: Get unlock codes
Communications Port (COM1), Provider: Microsoft, Driver ver.: 5.1.2600.0, Date: 1.7.2001
Baud rate: 19200
Baseband Processor: MT6235, HW Rev. C.00, SW Rev. A.01
Serial number: 84EB3BBD35B688E418A108098FC2ADB5
Testing external RAM...64 Mb
Detecting flash...NAND, ID: 00AD00A1-00800015, manufacturer: Hynix
Flash size: 128 Mb, page size: 2048 , bad blocks: 1
File system: 78 Mb @ 03200000
Firmware: A8205_PCB01_GPRS_MT6235B_S01.STARLING_G_05_20_02R_ D
Hardware IMEI 1: 3536320473xxxxx
Hardware IMEI 2: 3536320473xxxxx
Mounting system disk...#1
Reading unlock codes...Done

Thanks again
Greeting

mcandre · 09-18-2012, 15:43

Okay, it would be better if you made such settings in "DTR&RTS control" (in case of using your cable):
DTR=ON RTS=ON

09-16-2012, 11:38	#1 (permalink)
networker Freak Poster Join Date: Dec 2003 Location: Republic of Srpska-BiH Age: 49 Posts: 102 Member: 46290 Status: Offline Thanks Meter: 16	Alcatel ot800 not done with cable The phone does not boot, just goes on. Through smart moto works without problems. I use com1.

09-18-2012, 15:38	#7 (permalink)
networker Freak Poster Join Date: Dec 2003 Location: Republic of Srpska-BiH Age: 49 Posts: 102 Member: 46290 Status: Offline Thanks Meter: 16	EX115 done thanx to mcandre I swich DTR&RTS settings to SigmaBox (IGNITION) SigmaKey 1.12.00 987979xxx Sigma dongle 1.15, Initializing...OK SigmaKey 1.12.00 MTK: Get unlock codes Communications Port (COM1), Provider: Microsoft, Driver ver.: 5.1.2600.0, Date: 1.7.2001 Baud rate: 19200 Baseband Processor: MT6235, HW Rev. C.00, SW Rev. A.01 Serial number: 84EB3BBD35B688E418A108098FC2ADB5 Testing external RAM...64 Mb Detecting flash...NAND, ID: 00AD00A1-00800015, manufacturer: Hynix Flash size: 128 Mb, page size: 2048 , bad blocks: 1 File system: 78 Mb @ 03200000 Firmware: A8205_PCB01_GPRS_MT6235B_S01.STARLING_G_05_20_02R_ D Hardware IMEI 1: 3536320473xxxxx Hardware IMEI 2: 3536320473xxxxx Mounting system disk...#1 Reading unlock codes...Done Thanks again Greeting

09-17-2012, 07:24	#2 (permalink)
GSM_Support Product Supporter Join Date: Feb 2005 Location: GSMserver Team Posts: 36,981 Member: 121052 Status: Offline Sonork: 100.107126 Thanks Meter: 80,766	@ networker, What cable exactly are you using? Please specify step-by-step operation you perform. Best Regards GSMServer team

09-17-2012, 09:33	#3 (permalink)
networker Freak Poster Join Date: Dec 2003 Location: Republic of Srpska-BiH Age: 49 Posts: 102 Member: 46290 Status: Offline Thanks Meter: 16	I am using com port cable from siemens with whom I have never had a problem in communication with the phone (as I have with profilic or ftdi). SigmaKey 1:11:00 98797xxx Sigma dongle 1.14, Initializing ... OK SigmaKey 1:11:00 MTK: Get unlock codes Communications Port (COM1) Provider: Microsoft Driver ver.: 5.1.2600.0, Date: 07/01/2001 Baud rate: Autodetect Press and HOLD "Power on" button ... _ When I press Power on, the phone is turned on and the software does not show any error. The same procedure with SmartMoto goes out first. Greeting

09-17-2012, 09:38	#4 (permalink)
mcandre No Life Poster Join Date: Mar 2006 Location: Central Europe Age: 39 Posts: 11,877 Member: 239548 Status: Offline Thanks Meter: 2,781	Did you made any changes into "DTR&RTS settings" in sigmakey (options tab)?

09-18-2012, 13:00	#5 (permalink)
networker Freak Poster Join Date: Dec 2003 Location: Republic of Srpska-BiH Age: 49 Posts: 102 Member: 46290 Status: Offline Thanks Meter: 16	NO, I did not. I will try when I have another phone.

09-18-2012, 15:35	#6 (permalink)
mcandre No Life Poster Join Date: Mar 2006 Location: Central Europe Age: 39 Posts: 11,877 Member: 239548 Status: Offline Thanks Meter: 2,781	networker, what cable do you use, exactly? In case you are using USB cable, just select correct COM-Port in the Serial Port settings. If you use physical COM port cable, just make the next settings in "DTR&RTS control": DTR=ON RTS=ON

09-18-2012, 15:43	#8 (permalink)
mcandre No Life Poster Join Date: Mar 2006 Location: Central Europe Age: 39 Posts: 11,877 Member: 239548 Status: Offline Thanks Meter: 2,781	Okay, it would be better if you made such settings in "DTR&RTS control" (in case of using your cable): DTR=ON RTS=ON