spd 6820 not yet solved 100%

[segnattech]

i had some 6820 spd chip which is dead on software, now i write bin file, it was success but still dead. i notice that system file was not written while flashing, i make a pac file still stop at system. any solution



east 1.30 mins.
Note for win7 users :
Start your Win 7 64bit with F8 key and choose 'Disable Driver Signature Enforcement'.
After that the spd drivers will have the ability to be loaded.
Available Ports:COM12
Detection initiated...
Vcc: null
Gnd: 5
Analyzing D+ and D-...
D+ = 3, D- = 2
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM64), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00AD00BC90555600
Flash Type:[Hyundai] NAND_HY27UT088G2A
FLASH LEN:0x20000000
mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),10m(modem),3840k(fixnv),3840k(backupfixnv),51 20k(dsp),3840k(runtimenv),10m(boot),10m(recovery), 240m(system),150m(userdata),60m(cache),256k(misc), 1m(boot_logo),1m(fastboot_logo),3840k(productinfo) ,512k(kpanic)
Analysis flash internal data successfully.
Set to Factory successfully.

failed to open port.
Detection initiated...
Vcc: null
Gnd: 5
Analyzing D+ and D-...
D+ = 3, D- = 2
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM64), (VID_1782&PID_4D00)

Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00AD00BC90555600
Flash Type:[Hyundai] NAND_HY27UT088G2A
FLASH LEN:0x20000000
File partition was not found.
Detection initiated...
Failed to connect, please try again.
Pinouts are not fonud!
Detection initiated...
Vcc: null
Gnd: 5
Analyzing D+ and D-...
D+ = 3, D- = 2
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM64), (VID_1782&PID_4D00)


Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00AD00BC90555600
Flash Type:[Hyundai] NAND_HY27UT088G2A
Writing completed.
Flash file E:\VOLCANO\spd\6616820\BIN\m-horse i9500\_20140103_103718_FullFlash.bin has been written.
Ready to read/write again, please remove the power supply clip or battery and then re-loaded it.
Detection initiated...
Vcc: null
Gnd: 5
Analyzing D+ and D-...
D+ = 3, D- = 2
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM64), (VID_1782&PID_4D00)


Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00AD00BC90555600
Flash Type:[Hyundai] NAND_HY27UT088G2A
Writing completed.
Flash file E:\VOLCANO\spd\6616820\BIN\m-horse i9500\_20140103_103718_FullFlash.bin has been written.
Ready to read/write again, please remove the power supply clip or battery and then re-loaded it.
Detection initiated...
Vcc: null
Gnd: 5
Analyzing D+ and D-...
D+ = 3, D- = 2
Analyzing USB device, please wait...
Find USB device:SPRD U2S Diag (COM64), (VID_1782&PID_4D00)


Internal version: SPRD3
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.1
Boot downloaded.
Flash ID: 00AD00BC90555600
Flash Type:[Hyundai] NAND_HY27UT088G2A
Writing completed.
Flash file E:\VOLCANO\spd\6616820\BIN\m-horse i9500\_20140103_103718_FullFlash.bin has been written.
>>Ready to read/write again, please remove the power supply clip or battery and then re-loaded it.