eMMC ORC: 00000000, bad code ! >> Id check lost /// Solution Here \\\
 

GPGeMMC Box provided Special Adaptor for ISP and JTAG. Make sure for ISP read and write use ISP Adaptor/Jig and for ISP writing Use ISP correct Files. Don't use ISP files into JTAG and don't use JTAG files into ISP. ISP files are like this Boot1, Boot2, USER, etc. and Jtag files don't have Boot1. Boot2, User etc. so 1st of all make sure of this. 2ndly Triple Check your Soldering use Good Jumper Wires for Soldering and Good Solder and Good Iron. after all Trip Check if still you are getting Bad code error can be cause of two reasons 1st phone can be Hardware and 2nd use this method to make sure it's hardware issue or not.

Check this picture

http://www.gpgdragonsupport.com/ftpp...0volts/222.png

Some phones need Extra Current of 3.3 Volts and these type of phones not connect with box. when you try to connect it with GPGeMMC you got error
eMMC ORC: 00000000, bad code !
>> Id check lost
what you have to do is make sure your soldering are 101% correct after confirm just put 3.3v to ISP jig. Keep in mind no need to sold any extra 3.3v to phone. just you have to sold extra 3.3v to ISP adaptor. these kind of error comes on N7000, I9300, N7100 etc so i had tested many of these phones which was giving error so i research and found this solution and it's working fine. If you have I9300 type phones which no need 3.3 volts that type of phones need VCC which is 2.8 Volts. for those type of phones just put 2.8 Volts to ISP adaptor and phone will connect but again before Putting External volts you make sure your soldering is 101% correct. So for those type of phones which have Vcc pinouts and mobile giving error of bad code then you need to put 2.8 volts to VCC on ISP adaptor not to phone. and which phones have 3.3v pinouts and mobile giving error of bad code then you need to put 3.3 Volts to 3.3V on ISP adaptor not to phone. But again make sure your soldering are 100% correct. and IF even that phone showing BAD code error it's means your eMMC ic is TOTALLY DAMAGED !!!

here is some pictures i want to share with you


i got N7000 trying to repair it. but it's not connecting. i sold wires and verify it. even thing was fine but phone was not connecting here is screen shot ( i didn't sold External power on this screen shot )

http://www.gpgdragonsupport.com/ftpp...lts/before.jpg

then i sold External volts check here ( i use Battery to give 3.3 Volts )


http://www.gpgdragonsupport.com/ftpp...203_205312.jpg



http://www.gpgdragonsupport.com/ftpp...203_205223.jpg


after sold external power here is the results

http://www.gpgdragonsupport.com/ftpp...ts/n700000.jpg

and mobile Successfully Repaired !!!!

Good work Bro! thank u for your experiment.:)

this power supply also worked
this power supply generated by 3.3volt and 1.8volt
https://imagizer.imageshack.us/v2/44...90/37/5ng0.jpg

https://imagizer.imageshack.us/v2/79...0/546/lshm.jpg

my hand made
if you need more information i can make mannul how to make the power supply device

can you give this procedure?

why not
give me today
i give you full details tommarow

just post here the materials and procedure how to do it

hi
good job
we need to sold gnd from extra battery to adaptor vcc one ???

some pictures share above
& of course u can use it in n7000...
in n7000, there are 2 options of 3.3 and both jumper connection are necessory

have the same problem bro

3.3 volts from battery like ur screen shot are sold to adaptors 3.3 then whats about gnd from same source where we need to sold it or no needed gnd anymore ??

bro without gnd how to work ?
put it on pcb or adeptor

https://imagizer.imageshack.us/v2/35...0/401/f166.png

https://imagizer.imageshack.us/v2/12...0/855/s6m2.png

Hello sir
u make battery to external power 3.3v and 2.8
all the time Battery is 3.7v so how i can convert to 2.8 or 3.3v?
connect direct to ISP jig?
pls help me,thanks

u have more option .........................
this is easy way .Communication Maintenance Power Supply(bk 1501t+ Baku New Products) - Buy 10v Power Supply,110v Power Supply,2a Power Supply Product on Alibaba.com

yes,i have power supply simalar it :D
i will try thanks

How about N7100 ? i see it need 1.8v so no need external adapter?
pls tel me ,thanks

Hi,

is it work, external supply for this gpg emmc box, if its work no need to create external board i think, please once test and give report, if its work i will buy this,
http://www.icables.in/images/detaile...c-3in1-gpg.png

BR,
Srinivas Reddy.

SAMSUNG N7100
Read Info...
Device Ready...
Device Ready...OK!
ID check...
Level (V) : VCC V18 VCCQ D0 CMD CLK
Pullup : 0.78 0.03 0.64 0.35 0.00 0.00
Power ON : 2.63 1.75 2.54 1.02 1.65 0.01
-------------------------------------------------------------------
eMMC ORC: C0000000
eMMC CID: 0000000000000000,bad code!
>>ID check lost!

bro i have 2 set note n7100 but same error can you help me??

but how to connect power supply my mobile gt-i9300

how to connet wair
3.3v and VCC

bro read again & again if u cant understand
& use u r mind ..........

bro i9000 bad code error on isp there r 2 pic of that 1 is new 1 is old in old there is posted 3.3 volts on 2 points plz tell wich is the corrct point i have the same board l;ike old

dear sir,
i have problem...
please guide me sir...
this is my problem sir...
i9300 repair no product name

Read Info...
Device Ready...
Device Ready...OK!
ID check...
Level (V) : VCC V18 VCCQ D0 CMD CLK
Pullup : 0.09 0.00 2.75 0.00 0.00 0.00
Power ON : 2.80 1.77 3.30 1.55 2.07 0.01
-------------------------------------------------------------------
eMMC ORC: 00000000
eMMC CID: 0000000000000000,bad code!
>>ID check lost!

tqvm, sir

give me full detail
phone condition ?
what s problem in this phone ?

Hi,

I given image below for how to sold wire with external power supply from gpg emmc jig and i9300 emmc connection.
http://dc591.4shared.com/img/i6IAuXS...connection.jpg

BR,
Srinivas Reddy.

same problem with i9000...
simply explain why two points of 3,3V ? it's an error on picture? or how to connect this points? these two points need to connect together at 3,3V ?

Sir i have tried all those solutions for over the past 72 hrs and nothing works i have tested it on
5 * N7100
3 * I9300
2 * I9100 (dosen't work either isp or jtag)
1 * direct emmc (movinand samsung b503 fo S III )
1 * I9500
i supplied external current checked soldering over 10 times and every time i get these great message eMMC ORC: 00000000, bad code ! >> Id check lost or another CID error
and when trying jtag release power key >> phone dosent respond
bro it even cant jtag and isp seems to be a dead everytime

another remark when checking pin info at emmc section if you connected extra power supply you get all the pins green(good contact) remove extra supply and pins returns to normal i tried it on the 10+ phones and didn't return any positive responds just get lost every time
id check lost, write size lost, erase lost & finally Box get lost !!
sir i have spent 199 Grand for this great invention i only ask for some support to how to make use of this device i tried to change vcc 2.4, 2.6, 2.8
i tried putting external voltage source, i tried to write boot size, i changed writing speeds
nothing work every time you get lost

Bro just change 3.3 from(gpg isp ) to mobile vcc 100% TESTED I9300 4 Device All 4 Successs
(no need vcc from gps isp)

thanks bro i will try and post result im so grateful for your reply

this is also worked itested


thanks

this is also worked for me I tested


thanks

NO WORK PLEASE HELP
ID check...
Level (V) : VCC V18 VCCQ D0 CMD CLK
Pullup : 0.10 0.02 0.10 0.34 0.00 0.00
Power ON : 2.81 1.79 2.80 1.00 2.51 0.54
-------------------------------------------------------------------
eMMC ORC: 00000000,bad code!
>>Read chip lost!

i9070 dead boot condition when i try to read with isp it says chip lost on 22% need help also not giving info

https://imageshack.com/i/nfj4q3p

i9070 dead boot condition when i try to read with isp it says chip lost on 22% need help also not giving info

http://imageshack.com/a/img843/7751/j4q3.png

please need repair i9300 emmc how to

problem is hadware ''emmc killer'' solution exact change emmc 100%

please help i9300 dead emmc

Isp Connecting Solution Tested Many times
 

http://forum.gsmhosting.com/vbb/f899...l#post10144831

brother
 

brother picture or video 4 i9300 done:confused:

ID check ...
** Level (V): VCC V18 VCCQ D0 CLK CMD
** Pullup: 1.29 1.02 2.50 0.00 0.00 0.00
** Power ON: 2.82 1.80 3.25 0.69 2.51 0.00
** -------------------------------------------------- -----------------
** eMMC ORC: 00000000, bad code!

ID check >> lost!

any help will be appreciated.

I connect you directly with two power voltages 3.3 and 1.8 and I do not worry

which phone u are trying to conect..?

Regards

Samsung -i9300 please Help

Read Info...
Device Ready...
Device Ready...OK!
ID check...
Level (V) : VCC V18 VCCQ D0 CMD CLK
Pullup : 1.20 0.00 2.63 0.00 0.00 0.00
Power ON : 2.62 1.77 3.30 0.84 1.64 0.00
-------------------------------------------------------------------
eMMC ORC: 00FF8080
eMMC CID: 0000000000000000,bad code!
>>ID check lost!

samsung i9300

how to repair

change the vcc voltage to 2.80
if all connections are ok and still same earror then have to replace emmc


Regards

all user making mistake emmc box cant repair all the phones with isp flashing note2 , s3 etc ... sucess rate of repair hang logo and dead phones is 20-40% other which fail to connect have to replace emmc

Regards

@c_ahmad79

why everytime you answer you sound like either the user is the problem or the emmc/phone is the problem?

why don't you accept that the box itself have a problem that's why the product creator is doing the fix.

didn't you read their thread? their thread about the "adaptor" that will fix the connection problem?

look at your post above, none out of 4 i9300 is connecting properly, do you think it's because the emmc is dead? i bet those 4 i9300 can be connected properly to other box...

next time, before you do an advice, make sure you mention that the box have problems too, not just blaming the user or the emmc...