Zte blade a0621 only dfu mode recover done !! [USER REPORT]

[netvision123]

DFU TO EDL

Operation	: DFU2EDL
Searching for Device in DFU Mode...Found
Port	: Handset Diagnostic Interface(DFU) (COM34)
Hardware ID	: usb\vid_19d2&pid_0112&rev_0000
Switching to EDL Mode...Done
Device should enter EDL now.
Check device manager if 9008 port appears.
Operation Finished.
QcFire Ver. 4.4

DOWNLOAD FACTORY FILE IMAGE 7.1.1

Operation	: Flash
Checking for existing devices...Found
Port	: Qualcomm HS-USB QDLoader 9008 (COM7)
Driver Info	: Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID	: E1B00600 [8937] 00000400
OPK_DATA	: C7EF5E9C6DE5335E2E3B54BF2C47DFF605D327262E03B79E515436BF642B09F4
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_017]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware	: 8937, eMMC, 16 GB
LU Count	: 1 [0x01D5A000] 
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info	: In: 65536 [4096], Out: 1048576, Sector Size: 512
Writing [sbl1.mbn] -> [sbl1] ...Done
Writing [sbl1.mbn] -> [sbl1bak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [factory.img] -> [factory] ...Done
Writing [emmc_appsboot.mbn] -> [aboot] ...Done
Writing [emmc_appsboot.mbn] -> [abootbak] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [batweak.img] -> [batweak] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [sec.dat] -> [sec] ...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [adspso.bin] -> [dsp] ...Done
Writing [cmnlib.mbn] -> [cmnlib] ...Done
Writing [cmnlib.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64.mbn] -> [cmnlib64bak] ...Done
Writing [keymaster.mbn] -> [keymaster] ...Done
Writing [keymaster.mbn] -> [keymasterbak] ...Done
Writing [system.img ] -> [system]...Done
Writing [userdata.img] -> [userdata] ...Failed (Because of Encryption, its OK)
Operation Finished.
QcFire Ver. 4.4

After flash phone still will be on dfu mode because of user data flashing failure.

Again repeat the first Operation

DFU TO EDL

From edl to normal just press all button or just read info phone will restart after reading info to normal

Operation	: Read Information
Checking for existing devices...Found
Port	: Qualcomm HS-USB QDLoader 9008 (COM114)
Driver Info	: Qualcomm Incorporated, qu_usb_serial.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID	: E1B00600 [8937] 00000400
OPK_DATA	: C7EF5E9C6DE5335E2E3B54BF2C47DFF605D327262E03B79E515436BF642B09F4
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_017]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware	: 8937, eMMC, 16 GB
LU Count	: 1 [0x01D5A000] 
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info	: In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device	: ZTE ZTE BLADE A0620 [msm8937] [P840F12]
Software	: GEN_RU_A6_V1.0, 20171028.154803 [2017å¹´ 10月 28æ—¥ 星期å…* 15:48:03 CST]
Android Ver.	: 7.1.1
Patch Level	: 2017-11-01
USERDATA	: Encrypted
You can use DISABLE LOCKS to Disable Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 4.4

That's it

Br: Habib