Test Jig on MyV65 - GSM-Forum

mobymaster · 07-01-2004, 16:00

Hi,

I received today my dongle and test boxes from completegsm.

Worked fine on unlocking myx2s, then I tried a myv65 on.

Connected all up, np. Went to detect phone Np, and then went to unlock but "reboot phone". I checked the pcb for dirt/glue and there was nothing on the board, checked the test point adapters were not jammed and they were fine.

When it was connected, i noticed that the test point going to DB9.2 is 1mm off the actual point and is touching the pcb.

I put a bit of solder on the point and trailed it off, and it worked.

Has anyone else experienced these problems? Or is it a one off case?

Thanks in advance
John

fonetech · 07-01-2004, 16:02

i had same problem with my myx2 test jig, i just had to resolder all the pins so they all made contact and everything was fine

mobymaster · 07-01-2004, 16:06

Yeh but this one is 1 mm off.

You suggest i solder the pin and then bend the whole adapter so it lines up?

momi · 01-23-2005, 18:19

i dont no how to make the test point for sagem myv65 i need the help

When it was connected, i noticed that the test point going to DB9.2 is 1mm off the actual point and is touching the pcb.

I put a bit of solder on the point and trailed it off, and it worked.

Has anyone else experienced these problems? Or is it a one off case?

Thanks in advance
John[/QUOTE]

07-01-2004, 16:00	#1 (permalink)
mobymaster Freak Poster Join Date: Jul 2002 Location: Manchester, UK Posts: 259 Member: 13975 Status: Offline Thanks: 2 Thanked 7 Times in 5 Posts	Test Jig on MyV65 Hi, I received today my dongle and test boxes from completegsm. Worked fine on unlocking myx2s, then I tried a myv65 on. Connected all up, np. Went to detect phone Np, and then went to unlock but "reboot phone". I checked the pcb for dirt/glue and there was nothing on the board, checked the test point adapters were not jammed and they were fine. When it was connected, i noticed that the test point going to DB9.2 is 1mm off the actual point and is touching the pcb. I put a bit of solder on the point and trailed it off, and it worked. Has anyone else experienced these problems? Or is it a one off case? Thanks in advance John

01-23-2005, 18:19	#4 (permalink)
momi Junior Member Join Date: Jan 2005 Age: 39 Posts: 3 Member: 109192 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	test point sagem myv65 i dont no how to make the test point for sagem myv65 i need the help When it was connected, i noticed that the test point going to DB9.2 is 1mm off the actual point and is touching the pcb. I put a bit of solder on the point and trailed it off, and it worked. Has anyone else experienced these problems? Or is it a one off case? Thanks in advance John[/QUOTE]

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
3310 Works on test jig ONLY ... !!!!	Byte	Nokia Hardware & Hardware-Repair Area	4	12-04-2004 15:46
6100 works on test jig only ...!!!	Byte	Nokia Hardware & Hardware-Repair Area	9	11-29-2004 12:49
powers on test jig only ...!!!	Byte	Nokia Hardware & Hardware-Repair Area	2	08-01-2004 00:08
For SALE: Original Nokia Service Equipment - TEST JIGS / TEST BOXES / PKD-1NS / FPS-4	nokiaking	Sell ur Old and Used Stuff	4	01-04-2004 10:10

07-01-2004, 16:02	#2 (permalink)
fonetech No Life Poster Join Date: Sep 2002 Posts: 902 Member: 15837 Status: Offline Thanks: 0 Thanked 2 Times in 2 Posts	i had same problem with my myx2 test jig, i just had to resolder all the pins so they all made contact and everything was fine

07-01-2004, 16:06	#3 (permalink)
mobymaster Freak Poster Join Date: Jul 2002 Location: Manchester, UK Posts: 259 Member: 13975 Status: Offline Thanks: 2 Thanked 7 Times in 5 Posts	Yeh but this one is 1 mm off. You suggest i solder the pin and then bend the whole adapter so it lines up?