[khawar]

Originally Posted by Advance-Box

Here is official Samsung Instructions about TP on this tablet:
PVI 13-03A - GT-N8000 Recovery Bootloader (J-Tag) Guide - Download - 4shared - Linus Hernandez



Of course you can also write BOOT via eMMC direct connection if TP still not work.. Anyway read PDF and make SDC using ATF plus Image too.

Make sure your BOOT version is high version before making SDC.

---------------------------------------------------------------------------------
Sir ,I tried hard but could not boot with sd card,even the tp shortened correctly,
Than i connected EMMC testpoint and ,this way i Connected with EMMC successfully.
Than i wrote the latest fw 4.4.2 through tp,
------------------------------------------
================================================== ====
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.


Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 1501004D414732474107BB1FF1482FF7
CSD : D02701320F5903FFF6DBFFFF8A404007

eMMC Boot Information
Revision 1.5 (for MMC v4.41)
BOOT PARTITION : BOOT PARTITION 1
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x4 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 3584 KB
HC ERASE GROUP SIZE: 512 KB
USER AREA SIZE : 15758000128 BYTES
BOOT PARTITION SIZE: 2048 KB
RPMB PARTITION SIZE: 128 KB


eMMC Device Information
Manufacturer ID: SAMSUNG
Device Type : Embedded BGA
Application ID : 00
Product Name : MAG2GA
Product Rev : 0.7
Product SN : BB1FF148
Manufactured : January 2012

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 13 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
1501004D414732474107BB1FF1482FF7.ext_csd
Backup Directory:
C:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\




Start Writing Flash Images...



Flash Image: sboot.bin
Start Writing 0x000006C5 Blocks at 0x00000000
Partition Selected: BOOT 1

Total Elapsed Time 00:00:04
Write Success!


Flash Image: tz.img
Start Writing 0x00000138 Blocks at 0x000006C6
Partition Selected: BOOT 1

Total Elapsed Time 00:00:00
Write Success!


Flash Image: boot.img
Start Writing 0x00002CA5 Blocks at 0x00014000
Partition Selected: USER AREA

Total Elapsed Time 00:00:39
Write Success!


Flash Image: recovery.img
Start Writing 0x000035B5 Blocks at 0x00018000
Partition Selected: USER AREA

Total Elapsed Time 00:01:48
Write Success!


Warning: EXT3/4 Image Detected
Skipping system.img...


Flash Image: modem.bin
Start Writing 0x00006001 Blocks at 0x0001C000
Partition Selected: USER AREA

Total Elapsed Time 00:01:55
Write Success!


Warning: EXT3/4 Image Detected
Skipping cache.img...


Warning: EXT3/4 Image Detected
Skipping hidden.img...


Total Images Written: 5
Process Done!
------------------------------------------------------
But the tab is still dead.
Pl guide me what to do next,Should i do ''normal factory erase'' before write anything and what should exactly be written to the EMMC,to put tab in dnload mode?
----------------------------------------------------
the tab was dead while flashing this fw. N8000XXUDNH2_N8000OJVDNH1_XSG.