P30 Pro dead after FRP - GSM-Forum

Slaby6 · 01-04-2022, 16:51

Hi, I've an P30 Pro (VOG-L29c), phone was fully working, only FRP locked, bootloader locked.

Tried Erase FRP via Testpoint but unfortunately i selected Hi980_unlocked instead HI980.
Software after operation stucked at waiting for fastboot. Now phone is dead and enter only "Huawei USB COM 1.0", tried Erase FRP via HI980, but after that phone still dead.

Is there any solution to unbrick it?
Unfortunately don't know previous firmware(can't check it now), i'm sure it was on adnroid 10.

Slaby6 · 01-04-2022, 17:09

Log from Erase FRP via HI980_unlocked

[USB 1.0] ERASE FRP Selected Model : HiSilicon Kirin 980
Code Name : Hi980_Unlocked
Operation : Kirin Testpoint [2]
**Authenticating... OK
**Retrieving data... OK [4,56 MiB]
Scanning port... COM4
Connecting to port... OK
**Connection : USB 1.0 Full-Speed
**USB Driver : [HUAWEI Incorporated] HSPL_usbvcom - Version : 2.0.5.0
Initializing... OK
Writing patch1... OK 1,603s
Writing patch2... OK 0,261s
Writing patch3... OK 1,058s
Reading partition map... OK [71]
Searching for bootloader key... OK [3:10485760:5242880]
Patching bootloader... OK
Please disconnect device and enter testpoint again!
Scanning port... COM4
Connecting to port... OK
**Connection : USB 1.0 Full-Speed
**USB Driver : [HUAWEI Incorporated] HSPL_usbvcom - Version : 2.0.5.0
Writing sec_usb_xloader... OK 1,290s
Writing sec_usb_xloader2... OK 0,344s
Writing unlock1... OK 0,622s
Writing unlock2... OK 0,121s
Writing sec_fastboot... OK 31,189s
Waiting for fastboot...

Log from Erase FRP via HI980

USB 1.0] ERASE FRP
Scanning port... COM4
Connecting to port... OK
Connection : USB 1.0 Full-Speed
USB Driver : [HUAWEI Incorporated] HSPL_usbvcom - Version : 2.0.5.0
Selected Model : HiSilicon Kirin 980 [FRP]
Code Name : Hi980
Operation : Erase FRP [1]
Authenticating... OK
Retrieving data... OK [121,17 KiB]
Writing unlocktool1... OK 1,685s
Writing unlocktool2... OK 0,278s
Writing unlocktool3... OK 1,023s
Reading partition map... OK [3]
Searching FRP Lock... OK [2:524288:524288]
Erasing FRP... OK
UNLOCKTOOL 2021.12.29.0
Elapsed time : 26 seconds

Slaby6 · 01-04-2022, 18:56

Status update

Phone is alive, my bad, i must do the testpoint to hard on motherbard, tp shorted to GND, that's why it was booting into bootloder only, after removing short phone fully working without FRP.

Thanks Best Regards

01-04-2022, 16:51	#1 (permalink)
Slaby6 Junior Member Join Date: Jul 2004 Location: Poland_Poznan_ Age: 39 Posts: 36 Member: 73143 Status: Offline Thanks Meter: 2	P30 Pro dead after FRP Hi, I've an P30 Pro (VOG-L29c), phone was fully working, only FRP locked, bootloader locked. Tried Erase FRP via Testpoint but unfortunately i selected Hi980_unlocked instead HI980. Software after operation stucked at waiting for fastboot. Now phone is dead and enter only "Huawei USB COM 1.0", tried Erase FRP via HI980, but after that phone still dead. Is there any solution to unbrick it? Unfortunately don't know previous firmware(can't check it now), i'm sure it was on adnroid 10.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-04-2022, 17:09	#2 (permalink)
Slaby6 Junior Member Join Date: Jul 2004 Location: Poland_Poznan_ Age: 39 Posts: 36 Member: 73143 Status: Offline Thanks Meter: 2	Log from Erase FRP via HI980_unlocked [USB 1.0] ERASE FRP Selected Model : HiSilicon Kirin 980 Code Name : Hi980_Unlocked Operation : Kirin Testpoint [2] Authenticating... OK Retrieving data... OK [4,56 MiB] Scanning port... COM4 Connecting to port... OK Connection : USB 1.0 Full-Speed USB Driver : [HUAWEI Incorporated] HSPL_usbvcom - Version : 2.0.5.0 Initializing... OK Writing patch1... OK 1,603s Writing patch2... OK 0,261s Writing patch3... OK 1,058s Reading partition map... OK [71] Searching for bootloader key... OK [3:10485760:5242880] Patching bootloader... OK Please disconnect device and enter testpoint again! Scanning port... COM4 Connecting to port... OK Connection : USB 1.0 Full-Speed USB Driver : [HUAWEI Incorporated] HSPL_usbvcom - Version : 2.0.5.0 Writing sec_usb_xloader... OK 1,290s Writing sec_usb_xloader2... OK 0,344s Writing unlock1... OK 0,622s Writing unlock2... OK 0,121s Writing sec_fastboot... OK 31,189s Waiting for fastboot... Log from Erase FRP via HI980 USB 1.0] ERASE FRP Scanning port... COM4 Connecting to port... OK Connection : USB 1.0 Full-Speed USB Driver : [HUAWEI Incorporated] HSPL_usbvcom - Version : 2.0.5.0 Selected Model : HiSilicon Kirin 980 [FRP] Code Name : Hi980 Operation : Erase FRP [1] Authenticating... OK Retrieving data... OK [121,17 KiB] Writing unlocktool1... OK 1,685s Writing unlocktool2... OK 0,278s Writing unlocktool3... OK 1,023s Reading partition map... OK [3] Searching FRP Lock... OK [2:524288:524288] Erasing FRP... OK UNLOCKTOOL 2021.12.29.0 Elapsed time : 26 seconds

01-04-2022, 18:56	#3 (permalink)
Slaby6 Junior Member Join Date: Jul 2004 Location: Poland_Poznan_ Age: 39 Posts: 36 Member: 73143 Status: Offline Thanks Meter: 2	Status update Phone is alive, my bad, i must do the testpoint to hard on motherbard, tp shorted to GND, that's why it was booting into bootloder only, after removing short phone fully working without FRP. Thanks Best Regards