How to unlock C975? - GSM-Forum

mail0 · 06-19-2006, 15:08

How to unlock V975
B.L 0.6.3.6
SW R245_U_82.21.80I
Operator 3
I try with testpoint, but smartmoto can't find the phone

Mr.Tinkertrain · 06-19-2006, 15:11

@ mail0,

Unlock procedure for C975 phone with testpoint (boot versions starting from 6.36)

Using "Unlock via Testpoint" function of SmartMoto method

1. Perform C975 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

mail0 · 06-19-2006, 15:28

Searching for pnone.......no phone found

Quote:

@ mail0,

Unlock procedure for C975 phone with testpoint (boot versions starting from 6.36)

Using "Unlock via Testpoint" function of SmartMoto method

1. Perform C975 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

Mr.Tinkertrain · 06-19-2006, 15:41

@ mail0,

Can the phone be seen by Smart-Moto without TP?

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

mail0 · 06-19-2006, 16:26

Quote:

@ mail0,

Can the phone be seen by Smart-Moto without TP?

Yes, when I press search button with powered on phone, smartmoto detected C975

mail0 · 06-19-2006, 16:37

The testpoint picture on boot-loader is right?

gsm3005 · 06-19-2006, 17:39

Quote:

Originally Posted by mail0

The testpoint picture on boot-loader is right?

this v have no problem just perform tp carefully
without testpoint
Searching for phone... found Motorola Phone (C975), getting test interface... OK
Model C975
Firmware R245_U_82.21.80I
Reading info OK

with test point

SmartMoto 1.23
Clip serial: xxxxxxxxxxxxx, version: 2.26, initializing... OK
Searching for phone... no phone found
Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading bus width... OK
Reading flash id... Micron-MT28F1284W18BET (x2)
Phone group: C975,C980,V980
Hardware IMEI: xxxxxxxxxxxxxxxxxx
Security area saved to "S Blank Rainbow POG xxxxxxxxxxxxxx16.pds"
Unlocking phone... OK

mail0 · 06-19-2006, 18:50

I try with version smartmoto V1.22, and nothing

Mr.Tinkertrain · 06-20-2006, 08:11

@ mail0,

Try to update your Smart-Moto and Smart-Clip. After that try to unlock your phone again.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

chowdary · 06-20-2006, 11:26

Quote:

Originally Posted by Mr.Tinkertrain

@ mail0,

Unlock procedure for C975 phone with testpoint (boot versions starting from 6.36)

Using "Unlock via Testpoint" function of SmartMoto method

1. Perform C975 testpoint procedure
2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

and that does not and will not include
Firmware R245_U_82.21.91I
am i right?

Mr.Tinkertrain · 06-20-2006, 12:24

@ chowdary,

R245_U_82.21.91I currently not supported version.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

Burnt Cobba · 06-20-2006, 22:17

having similar problems also with another C975 (2 in a day wow)

this one is ....

Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading bus width... OK
Reading flash id... 0x006C-0x00B1 (x2)
Phone group: A835,A845,A920,A925
Reading OTP... error B8
Warning: OTP read failed
Unlocking phone... error A0

end result ..... phone dead (no power)

FU_Too · 06-20-2006, 23:45

Quote:

Originally Posted by Burnt Cobba

having similar problems also with another C975 (2 in a day wow)

this one is ....

Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading bus width... OK
Reading flash id... 0x006C-0x00B1 (x2)
Phone group: A835,A845,A920,A925
Reading OTP... error B8
Warning: OTP read failed
Unlocking phone... error A0

end result ..... phone dead (no power)

I think you were lucky,

Searching for phone... found Motorola Phone (C975), getting test interface... OK
Model C975
Firmware R245_U_82.21.80I
Reading info OK

SmartMoto 1.23
Clip serial: xxxxxxxxx, version: 2.26, initializing... OK
Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading bus width... OK
Reading flash id... unable to retrieve flash id
Reading OTP... error B8
Warning: OTP read failed
Unlocking phone... error 9B

Clip serial: xxxxxxxxx, version: 2.26, initializing... OK
Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading bus width... OK
Reading flash id... Micron-MT28F1284W18BET (x2)
Phone group: C975,C980,V980
Hardware IMEI: F72410000633436
Security area saved to "S Blank Rainbow POG F72410000633436.pds"
Unlocking phone... error 9B

Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading bus width... OK
Reading flash id... Micron-MT28F1284W18BET (x2)
Phone group: C975,C980,V980
Hardware IMEI: F72410000633436
Security area saved to "S Blank Rainbow POG F72410000633436 (1).pds"
Unlocking phone... clip communication failed

Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 3.10
Reading bus width... OK
Reading flash id... Micron-MT28F1284W18BET (x2)
Phone group: C975,C980,V980
Hardware IMEI: F72410000633436
Security area saved to "S Blank Rainbow POG F72410000633436 (3).pds"
Unlocking phone... error A0

Now not only dead phone but also clip give error every search and always "phone not found" with every phone.
So basically dead phone and dead clip

Burnt Cobba · 06-21-2006, 06:13

Great Scott

what the heck is going on ??

how is this possible? Never met such a situation. I tired with 2.25 before updating and now with 2.26 and still same problem. The phone died when i tried with the new update. Presume there is a bug somewhere.

How can such a phone be revived now? Flashing with the same version?

Please SC team can you help with this... seems there is some problem with C975.

Mr.Tinkertrain · 06-21-2006, 08:00

@ Burnt Cobba,

Reading flash id... 0x006C-0x00B1 means that flash memory chip is not read properly. There are two main reasons for that:
1. The flash memory chip is damaged or doesn't communicate with the processor. In this case the phone needs hardware repair.
Connection between the chip and the PCB may be improved by the hot air.
2. Testpoint procedure was not performed properly -- just to make sure please, repeat the tp procedure.

@ FU_Too,

Please write a letter to support @ smart-clip.com
In letter please specify your problem and serial number.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

06-19-2006, 15:08	#1 (permalink)
mail0 No Life Poster Join Date: Feb 2006 Location: URL - UnlockRepairLandia Age: 41 Posts: 866 Member: 236218 Status: Offline Thanks Meter: 35	How to unlock C975? How to unlock V975 B.L 0.6.3.6 SW R245_U_82.21.80I Operator 3 I try with testpoint, but smartmoto can't find the phone

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how to unlock c975 motorola	prem2007	Smart-Clip	2	03-22-2008 09:11
help how to unlock c975 with smart moto	ARAB GSM	Smart-Clip	3	12-19-2005 16:00
Here how to unlock C975	vicky_ocean	Smart-Clip	0	07-26-2005 03:06

06-19-2006, 15:11	#2 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ mail0, Unlock procedure for C975 phone with testpoint (boot versions starting from 6.36) Using "Unlock via Testpoint" function of SmartMoto method 1. Perform C975 testpoint procedure 2. Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

06-19-2006, 15:41	#4 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ mail0, Can the phone be seen by Smart-Moto without TP? Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

06-19-2006, 16:37	#6 (permalink)
mail0 No Life Poster Join Date: Feb 2006 Location: URL - UnlockRepairLandia Age: 41 Posts: 866 Member: 236218 Status: Offline Thanks Meter: 35	The testpoint picture on boot-loader is right?

06-19-2006, 18:50	#8 (permalink)
mail0 No Life Poster Join Date: Feb 2006 Location: URL - UnlockRepairLandia Age: 41 Posts: 866 Member: 236218 Status: Offline Thanks Meter: 35	I try with version smartmoto V1.22, and nothing

06-20-2006, 08:11	#9 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ mail0, Try to update your Smart-Moto and Smart-Clip. After that try to unlock your phone again. Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

06-20-2006, 12:24	#11 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ chowdary, R245_U_82.21.91I currently not supported version. Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

06-20-2006, 22:17	#12 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	having similar problems also with another C975 (2 in a day wow) this one is .... Searching for phone... found S Blank Rainbow POG, getting test interface... interface not found Switching to flash mode... OK Reading phone boot version... 3.10 Reading bus width... OK Reading flash id... 0x006C-0x00B1 (x2) Phone group: A835,A845,A920,A925 Reading OTP... error B8 Warning: OTP read failed Unlocking phone... error A0 end result ..... phone dead (no power)

06-21-2006, 06:13	#14 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	Great Scott what the heck is going on ?? how is this possible? Never met such a situation. I tired with 2.25 before updating and now with 2.26 and still same problem. The phone died when i tried with the new update. Presume there is a bug somewhere. How can such a phone be revived now? Flashing with the same version? Please SC team can you help with this... seems there is some problem with C975.

06-21-2006, 08:00	#15 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ Burnt Cobba, Reading flash id... 0x006C-0x00B1 means that flash memory chip is not read properly. There are two main reasons for that: 1. The flash memory chip is damaged or doesn't communicate with the processor. In this case the phone needs hardware repair. Connection between the chip and the PCB may be improved by the hot air. 2. Testpoint procedure was not performed properly -- just to make sure please, repeat the tp procedure. @ FU_Too, Please write a letter to support @ smart-clip.com In letter please specify your problem and serial number. Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com