[HowTo] : Do not panic!

[AhNaF Telecom]

Again Failed,

Card found : CDF78CED , v0147
Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.20

Load IDBase v125162 Ok!

Update configuration ...
Update Ok!
Load IDBase v125162 Ok!

Operation : HW Report [ v2.20 ]
HWreport : Mode : eMMC
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM35)
MODE : BOOTROM
PORT : 35
Error : Failed to open port!
Info : LEGACY : HW reporting feature unavailable for current device!


Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!


Operation : HW Report [ v2.20 ]
HWreport : Mode : eMMC
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM35)
MODE : BOOTROM
PORT : 35
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Cervino
TYPE : MODERN RAPHAEL
BROM : MEID : AA7783F2AF7B257EFFA5F144D843657A
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Disabled
BROM : SOCID : 8F9CB31E12D223170B9CCC1E6FD941FFABC9F860BE948E823A 08F6A20C4EB5A7
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : PRELOADER_INFINITY_3
EMI : CNT : 0001
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...

DA : BOOT 2ND DA FAILED!
ERR : 0xC0070004
ERR : DA_HASH MISMATCH

Boot done!

Memory Info :
CID : 90014A68423861503E030016B720A7A9
MEM : VEN : HYNIX | OEM : 4A01 | DEV : hB8aP>
DAT : Size: 29820 MB, Max.Speed: 52000 kHz, blklen(512), nblks(61071360), ro(0)

EXT_CSD Info :
EXT_CSD rev. : v1.8 ( MMC v5.1 )
CSD struct rev. : v1.2
Supported command sets : 1h
HPI features : 1h
BG operations support : 1h
BG operations status : 0h
Correct prg. sectors : 0h
1st init time after part. : 1000 ms
Min. write perf.(DDR,52MH,8b): 0h
Min. read perf. (DDR,52MH,8b): 0h
TRIM timeout: 0 ms
Secure feature support: 55h
Secure erase timeout : 150000 ms
Secure trim timeout : 150000 ms
Access size : 3584 bytes
HC erase unit size : 512 kbytes
HC erase timeout : 600 ms
HC write prot grp size: 8192 kbytes
HC erase grp def. : 0h
Reliable write sect count: 1h
Sleep current (VCC) : 8h
Sleep current (VCCQ): 9h
Sleep/awake timeout : 419430400 ns
Sector count : 3a3e000h
Min. WR Perf. (52MH,8b): 78h
Min. Read Perf.(52MH,8b): 8ch
Min. WR Perf. (26MH,8b,52MH,4b): 46h
Min. Read Perf.(26MH,8b,52MH,4b): 46h
Min. WR Perf. (26MH,4b): 1eh
Min. Read Perf.(26MH,4b): 1eh
Power class: 0
Power class(DDR,52MH,3.6V): 0h
Power class(DDR,52MH,1.9V): 0h
Power class(26MH,3.6V) : 0h
Power class(52MH,3.6V) : 0h
Power class(26MH,1.9V) : 0h
Power class(52MH,1.9V) : 0h
Part. switch timing : 1h
Out-of-INTR busy timing: ah
Card type : 57h
Command set : 0h
Command set rev.: 0h
HS timing : 0h
Bus width : 0h
Erase memory content : 0h
Partition config : 48h
Boot partition size : 4096 kbytes
Boot information : 7h
Boot config protection: 0h
Boot bus width : 2h
Boot area write prot : 0h
User area write prot : 0h
FW configuration : 0h
RPMB size : 16384 kbytes
Write rel. setting : 1fh
Write rel. parameter: 15h
Start background ops : 0h
Enable background ops: 2h
H/W reset function : 1h
HPI management : 0h
Max. enhanced area size : 747h (15261696 kbytes)
Part. support : 7h
Part. attribute: 0h
Part. setting : 0h
General purpose 1 size : 0h (0 kbytes)
General purpose 2 size : 0h (0 kbytes)
General purpose 3 size : 0h (0 kbytes)
General purpose 4 size : 0h (0 kbytes)
Enh. user area size : 0h (0 kbytes)
Enh. user area start: 0h
Bad block mgmt mode: 0h

Overall status :

MLC status : 0% - 10% used
SLC status : Not defined
EOL status : Normal ( Less than 80% reserved blocks used )


Done!
Elapsed: 00:00:23

Operation : Reset Settings/Format FS [ v2.20 ]
Mode : FULL FACTORY ( FORCED + FRP )
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM35)
MODE : BOOTROM
PORT : 35
Error : Failed to open port!

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

Operation : Reset Settings/Format FS [ v2.20 ]
Mode : FULL FACTORY ( FORCED + FRP )
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM35)
MODE : BOOTROM
PORT : 35
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Cervino
TYPE : MODERN RAPHAEL
BROM : MEID : AA7783F2AF7B257EFFA5F144D843657A
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Disabled
BROM : SOCID : 8F9CB31E12D223170B9CCC1E6FD941FFABC9F860BE948E823A 08F6A20C4EB5A7
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6765
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : PRELOADER_INFINITY_3
EMI : CNT : 0001
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...

DA : BOOT 2ND DA FAILED!
ERR : 0xC0070004
ERR : DA_HASH MISMATCH

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

Where problem?

[jonny12345]

sir Lava Iris88 not support. i have device in hand now





Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM118)
MODE : BOOTROM
PORT : 118
Error : Failed to open port!

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM118)
MODE : BOOTROM
PORT : 118
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Zion
TYPE : MODERN RAPHAEL
BROM : MEID : 2F59DFA0964DDB982DF85A2C90BB6322
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : BQ : SEC_6739 | Manual : Disabled
BROM : SOCID : 266DC60FDDE6545866F071EA79EE1719AFB2C9D69BA0250B89 8974FB4033548A
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL.bin
AGENT : Found MT6739
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!

DA : SETUP HW PARAMS FAILED! PROTO_VER is OLD?

Error : Fail to init protocol!
>>> Check and select CORRECT SETTINGS for your device!

Reconnect Power/Cable!

[Franky_36]

Originally Posted by jonny12345

sir Lava Iris88 not support. i have device in hand now





Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM118)
MODE : BOOTROM
PORT : 118
Error : Failed to open port!

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM118)
MODE : BOOTROM
PORT : 118
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Zion
TYPE : MODERN RAPHAEL
BROM : MEID : 2F59DFA0964DDB982DF85A2C90BB6322
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : BQ : SEC_6739 | Manual : Disabled
BROM : SOCID : 266DC60FDDE6545866F071EA79EE1719AFB2C9D69BA0250B89 8974FB4033548A
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL.bin
AGENT : Found MT6739
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!

DA : SETUP HW PARAMS FAILED! PROTO_VER is OLD?

Error : Fail to init protocol!
>>> Check and select CORRECT SETTINGS for your device!

Reconnect Power/Cable!

Hi, take a look at this video and see if it works for you.
https://www.youtube.com/watch?v=I1qQlm6s7I8

BR

[PASSIONATE_BOYS]

Originally Posted by jonny12345

sir Lava Iris88 not support. i have device in hand now





Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM118)
MODE : BOOTROM
PORT : 118
Error : Failed to open port!

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MTK USB Port (COM118)
MODE : BOOTROM
PORT : 118
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Zion
TYPE : MODERN RAPHAEL
BROM : MEID : 2F59DFA0964DDB982DF85A2C90BB6322
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : BQ : SEC_6739 | Manual : Disabled
BROM : SOCID : 266DC60FDDE6545866F071EA79EE1719AFB2C9D69BA0250B89 8974FB4033548A
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL.bin
AGENT : Found MT6739
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!

DA : SETUP HW PARAMS FAILED! PROTO_VER is OLD?

Error : Fail to init protocol!
>>> Check and select CORRECT SETTINGS for your device!

Reconnect Power/Cable!

Hello,
Download and install latest driver from support area.
Connect phone once with software, close software ,open again and do required operation.
Hope will get solved.
And with latest version no need any DA or PRL.

Br.
Infinity-Box Team.

[Varazdat]

Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM71)
MODE : BOOTROM
PORT : 71
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Talbot
TYPE : MODERN RAPHAEL
BROM : MEID : 839C5CBA14539C16D4FD81470B63AB69
BROM : SecLevel : 0x000000E7
BROM : SecMode : SBC+SLA+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Disabled
BROM : SOCID : 5BFFF127E0191460D6A06A17CA8E4380173848C7860AD67A9E 516C02B4C6B873
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6768
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : PRELOADER_INFINITY_0
EMI : CNT : 0001
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00070000 [ 448.00 KB ]
DRAM: 0x100000000 [ 4.00 GB ]

EMMC: 150100445036444142032BE6D40457CB
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : DP6DAB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0xE8F800000 [ 58.24 GB ]

CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0001 , EVOL : 0x0000

RNID : 65D62B71F320EBFDBBF0EE1575E89456

DA : USB : HIGH-SPEED

Boot done!

Product Brand : Redmi
Product Device : lancelot
Product Model : lancelot
Product Name : lancelot_global
Patch Level : QP1A.190711.020
Display ID : build-20201215100645
Ver. CodeName : REL
Ver. Release : 10
Sec. Patch : 2020-11-01
Build Time : 15.12.2020
Product Info : lancelot
Product Manfct : Xiaomi
Product Board : lancelot
Board Platform : mt6768

USERDATA : FILESYSTEM : EXT4 with FBE ( File-Base Encryption )

NVRAM check : Passed!
NVRAM : SEC SIGNED [ IMEI RSA SIGNED ]

Backup sensetive data [ 11 ]
Backup path : Backup\MT6768__65D62B71F320EBFDBBF0EE1575E89456\
[23] Read : NVRAM
[13] Read : NVDATA
[20] Read : PROINFO
[33] Read : LK
[12] Read : NVCFG
[16] Read : PROTECT1
[17] Read : PROTECT2
[14] Read : PERSIST
[0] Read : PRELOADER
[18] Read : SECCFG
Backup done!


STORAGE : LifeStatus : eMMC : OK!

Done!
Elapsed: 00:01:18

trying to flashing add log later...

[Varazdat]

NWRAM IS LOST AFTER !!! FOR FIRST DO BACKUP!!!


1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM71)
MODE : BOOTROM
PORT : 71
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Talbot
TYPE : MODERN RAPHAEL
BROM : MEID : 839C5CBA14539C16D4FD81470B63AB69
BROM : SecLevel : 0x000000E7
BROM : SecMode : SBC+SLA+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Disabled
BROM : SOCID : 5BFFF127E0191460D6A06A17CA8E4380173848C7860AD67A9E 516C02B4C6B873
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6768
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6752
EMI : SRC : preloader_lancelot.bin
EMI : CNT : 0008
EMI : [00] : eMMC : LP_DDR4X : ID : 150100444436384D42 : VEN : SAMSUNG | DEV : DD68MB : RAM : [ 3.00 GB ]
EMI : [01] : eMMC : LP_DDR4X : ID : 13014E53304A394A38 : VEN : MICRON | DEV : S0J9J8 : RAM : [ 3.00 GB ]
EMI : [02] : eMMC : LP_DDR4X : ID : 150100445636444D42 : VEN : SAMSUNG | DEV : DV6DMB : RAM : [ 4.00 GB ]
EMI : [03] : eMMC : LP_DDR4X : ID : 150100445036444142 : VEN : SAMSUNG | DEV : DP6DAB : RAM : [ 4.00 GB ]
EMI : [04] : eMMC : LP_DDR4X : ID : 13014E47314A395238 : VEN : MICRON | DEV : G1J9R8 : RAM : [ 4.00 GB ]
EMI : [05] : eMMC : LP_DDR4X : ID : 90014A684445615033 : VEN : HYNIX | DEV : hDEaP3 : RAM : [ 6.00 GB ]
EMI : [06] : eMMC : LP_DDR4X : ID : 150100335036434D42 : VEN : SAMSUNG | DEV : 3P6CMB : RAM : [ 6.00 GB ]
EMI : [07] : eMMC : LP_DDR4X : ID : 13014E47314A395339 : VEN : MICRON | DEV : G1J9S9 : RAM : [ 4.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00070000 [ 448.00 KB ]
DRAM: 0x100000000 [ 4.00 GB ]

EMMC: 150100445036444142032BE6D40457CB
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : DP6DAB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0xE8F800000 [ 58.24 GB ]

CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0001 , EVOL : 0x0000

RNID : 65D62B71F320EBFDBBF0EE1575E89456

DA : USB : HIGH-SPEED

Boot done!

[FL] : HW verification passed!

SEC_DL : False (RAPHAEL)
SEC_ID : 0x494E46494E495459424F584245535432

[FL] : Pre-Erase
Erase : 0x0000000000000000 : 0x000000000A4A2000
Erase : 0x000000000C4A2000 : 0x0000000004000000
Erase : 0x0000000017800000 : 0x0000000000A00000
Erase : 0x0000000018500000 : 0x0000000001A00000
Erase : 0x000000001DF00000 : 0x000000030E900000

[FL] : RePartition
[FL] : RePartition Ok!


[FL] : Flashing now ...

Write : PRELOADER
Update bootloader backup copy ...
Update bootloader backup copy Ok!
Write : RECOVERY
Write : VBMETA
Write : VBMETA_SYSTEM
Write : VBMETA_VENDOR
Write : LOGO
Write : MD1IMG
Write : SPMFW
Write : SCP1
Write : SCP2
Write : SSPM_1
Write : SSPM_2
Write : LK
Write : LK2
Write : BOOT
Write : DTBO
Write : TEE1
Write : TEE2
Write : EXAID
FAIL : SEC : IMG TOO LARGE
Write : CUST
FAIL : SEC : IMG TOO LARGE
Write : SUPER
Write : CACHE
Write : USERDATA

Ultra : Ok!

SEC_DL : False (RAPHAEL)
SEC_ID : 0x494E46494E495459424F584245535432

[FL] : RePartition
[FL] : RePartition Ok!

[FL] : Flashing finished!

Done!
Elapsed: 00:03:23

Reconnect Power/Cable!

[khanzada606]

upload video tutorial on YouTube is the best and easiest way for noobs like me 😥

[BANEHJOK]

plz helpe:

=== DongleManager [Infinity] v1.81 [29/01/2021 20:54:07] ===
Box/Dongle type selected: Infinity-Box/Dongle [CM2]
Card-Reader: Generic EMV Smartcard Reader 0
HWID: 0275079918944812
=== Process started: 29/01/2021 20:54:07 ===
Connecting to server
Server connection successfully established
Checking DongleManager version...
Version check error:
Socket Error # 10054
Connection reset by peer.

[ganjbek]

Xiaomi Redmi note 9 merlin muiu 12.0.6 downgrade miui 11 flashed ok



Operation : Write Flash [ v2.20 ]

Repartition : Enabled
Flash Verify : Disabled
Reg.Pre-Erase : Enabled
Verify HW/SW : Enabled
SData Backup : Disabled
Safe UserData : Disabled
Flash Format : Disabled

Files :23
[FL] : Set : preloader_merlin.bin
[FL] : Set : recovery.img
[FL] : Set : vbmeta.img
[FL] : Set : vbmeta_system.img
[FL] : Set : vbmeta_vendor.img
[FL] : Set : logo.bin
[FL] : Set : md1img.img
[FL] : Set : spmfw.img
[FL] : Set : scp.img
[FL] : Set : scp.img
[FL] : Set : sspm.img
[FL] : Set : sspm.img
[FL] : Set : lk.img
[FL] : Set : lk.img
[FL] : Set : boot.img
[FL] : Set : dtbo.img
[FL] : Set : tee.img
[FL] : Set : tee.img
[FL] : Set : exaid.img
[FL] : Set : cust.img
[FL] : Set : super.img
[FL] : Set : cache.img
[FL] : Set : userdata.img

[FL] : Total size : 0x16C36AF40 [ 5,69 GB ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM94)
MODE : BOOTROM
PORT : 94
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Talbot
TYPE : MODERN RAPHAEL
BROM : MEID : 7A0F5ACC74B3B3A0314101A4BE7B54FC
BROM : SecLevel : 0x000000E7
BROM : SecMode : SBC+SLA+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Disabled
BROM : SOCID : 5E15AE61AE5607FB78ED3E0E358FD94A35C9786E53EF6A2E8F 833902DAC72BFC
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6768
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6752
EMI : SRC : preloader_merlin.bin
EMI : CNT : 0009
EMI : [00] : eMMC : DDR3 : ID : 90014A68423861503E : VEN : HYNIX | DEV : hB8aP> : RAM : [ 3,00 GB ]
EMI : [01] : eMMC : LP_DDR4X : ID : 150100335636434D42 : VEN : SAMSUNG | DEV : 3V6CMB : RAM : [ 6,00 GB ]
EMI : [02] : eMMC : LP_DDR4X : ID : 150100334836434142 : VEN : SAMSUNG | DEV : 3H6CAB : RAM : [ 6,00 GB ]
EMI : [03] : eMMC : LP_DDR4X : ID : 13014E53304A394B38 : VEN : MICRON | DEV : S0J9K8 : RAM : [ 4,00 GB ]
EMI : [04] : eMMC : LP_DDR4X : ID : 150100444836444142 : VEN : SAMSUNG | DEV : DH6DAB : RAM : [ 4,00 GB ]
EMI : [05] : eMMC : LP_DDR4X : ID : 150100445036444142 : VEN : SAMSUNG | DEV : DP6DAB : RAM : [ 4,00 GB ]
EMI : [06] : eMMC : LP_DDR4X : ID : 13014E47314A395339 : VEN : MICRON | DEV : G1J9S9 : RAM : [ 4,00 GB ]
EMI : [07] : eMMC : LP_DDR4X : ID : 13014E53304A394A38 : VEN : MICRON | DEV : S0J9J8 : RAM : [ 3,00 GB ]
EMI : [08] : eMMC : LP_DDR4X : ID : 150100445636444142 : VEN : SAMSUNG | DEV : DV6DAB : RAM : [ 4,00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00070000 [ 448,00 KB ]
DRAM: 0x100000000 [ 4,00 GB ]

EMMC: 13014E53304A394A38101F8E1FF68745
EMMC: VEN : MICRON | OEM : 4E01 | DEV : S0J9J8
EMMC:
BOOT1 : 0x00400000 [ 4,00 MB ]
BOOT2 : 0x00400000 [ 4,00 MB ]
RPMB : 0x01000000 [ 16,00 MB ]
USER : 0xE8F800000 [ 58,24 GB ]

CHIP : MT6768 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0001 , EVOL : 0x0000

RNID : 35D426FF8BD1A185AF5175953B8CD2E1

DA : USB : HIGH-SPEED

Boot done!

[FL] : HW verification passed!

SEC_DL : False (RAPHAEL)
SEC_ID : 0x494E46494E495459424F584245535432

[FL] : Pre-Erase
Erase : 0x0000000000000000 : 0x000000000A4A2000
Erase : 0x000000000C4A2000 : 0x0000000004000000
Erase : 0x0000000017800000 : 0x0000000000A00000
Erase : 0x0000000018500000 : 0x0000000001A00000
Erase : 0x000000001DF00000 : 0x000000030E900000

[FL] : RePartition
[FL] : RePartition Ok!


[FL] : Flashing now ...

Write : PRELOADER
Update bootloader backup copy ...
Update bootloader backup copy Ok!
Write : RECOVERY
Write : VBMETA
Write : VBMETA_SYSTEM
Write : VBMETA_VENDOR
Write : LOGO
Write : MD1IMG
Write : SPMFW
Write : SCP1
Write : SCP2
Write : SSPM_1
Write : SSPM_2
Write : LK
Write : LK2
Write : BOOT
Write : DTBO
Write : TEE1
Write : TEE2
Write : EXAID
FAIL : SEC : IMG TOO LARGE
Write : CUST
FAIL : SEC : IMG TOO LARGE
Write : SUPER
Write : CACHE
Write : USERDATA

Ultra : Ok!

SEC_DL : False (RAPHAEL)
SEC_ID : 0x494E46494E495459424F584245535432

[FL] : RePartition
[FL] : RePartition Ok!

[FL] : Flashing finished!

Done!
Elapsed: 00:03:25

Reconnect Power/Cable!

[karim1980]

reno 2f failed

Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM93)
MODE : BOOTROM
PORT : 93
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Sylvia
TYPE : MODERN RAPHAEL
BROM : MEID : 7FEE66FC1208C993D72BF02714AB1F50
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Disabled
BROM : SOCID : 762D23CDCF8395B8B52A88FAFC11CF88FBCBEBFE9F99BED79C 19AF8AD3780892
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6771
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
DA : EMI : Failed to get EMI info from selected source!

Boot done!


Done!
Elapsed: 00:00:21

Reconnect Power/Cable!

[karim1980]

reno 2f failed

Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM93)
MODE : BOOTROM
PORT : 93
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Sylvia
TYPE : MODERN RAPHAEL
BROM : MEID : 7FEE66FC1208C993D72BF02714AB1F50
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Disabled
BROM : SOCID : 762D23CDCF8395B8B52A88FAFC11CF88FBCBEBFE9F99BED79C 19AF8AD3780892
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6771
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
DA : EMI : Failed to get EMI info from selected source!

Boot done!


Done!
Elapsed: 00:00:21

Reconnect Power/Cable!

[Franky_36]

Clarifications:
- Preloader Port protocol: The phone is completely turned off and we do not press any key that is to say neither vol + nor vol- or both at the same time and we connect with the usb cable.
-Brom Port protocol: The phone is completely off and we press vol +, vol- or both keys at the same time depending on the brand and model of the phone and connect with the usb cable, in some phones we have to force boot with test point.

BR

[JayDi]

Originally Posted by karim1980

reno 2f failed

Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM93)
MODE : BOOTROM
PORT : 93
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Sylvia
TYPE : MODERN RAPHAEL
BROM : MEID : 7FEE66FC1208C993D72BF02714AB1F50
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Disabled
BROM : SOCID : 762D23CDCF8395B8B52A88FAFC11CF88FBCBEBFE9F99BED79C 19AF8AD3780892
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6771
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
DA : EMI : Failed to get EMI info from selected source!

Boot done!


Done!
Elapsed: 00:00:21

Reconnect Power/Cable!

Select OPPO - Reno 2f from list ansd repeat.

[zainulabedin]

Dear Infinty team waiting your qualcomm blast update for oppo realme vivo

[karim1980]

Originally Posted by JayDi

Select OPPO - Reno 2f from list ansd repeat.

just amazing



Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.20

Load IDBase v125162 Ok!


Operation : Identify [ v2.20 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM131)
MODE : BOOTROM
PORT : 131
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Sylvia
TYPE : MODERN RAPHAEL
BROM : MEID : 7FEE66FC1208C993D72BF02714AB1F50
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : Oppo : F11-Reno2F | Manual : Disabled
BROM : SOCID : 762D23CDCF8395B8B52A88FAFC11CF88FBCBEBFE9F99BED79C 19AF8AD3780892
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6771
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6752
EMI : SRC : preloader_oppo6771.bin
EMI : CNT : 001A
EMI : [00] : eMMC : LP_DDR4X : ID : 150100445636444D42 : VEN : SAMSUNG | DEV : DV6DMB : RAM : [ 4.00 GB ]
EMI : [01] : eUFS : LP_DDR4X : DEV : KM5V8001DM-B622 : RAM : [ 4.00 GB ]
EMI : [02] : eMMC : LP_DDR4X : ID : 150100335636434D42 : VEN : SAMSUNG | DEV : 3V6CMB : RAM : [ 6.00 GB ]
EMI : [03] : eUFS : LP_DDR4X : DEV : KM5V7001DM-B621 : RAM : [ 4.00 GB ]
EMI : [04] : eMMC : LP_DDR4X : ID : 150100334836434142 : VEN : SAMSUNG | DEV : 3H6CAB : RAM : [ 6.00 GB ]
EMI : [05] : eMMC : LP_DDR4X : ID : 90014A68433861503E : VEN : HYNIX | DEV : hC8aP> : RAM : [ 6.00 GB ]
EMI : [06] : eMMC : LP_DDR4X : ID : 13014E53304A394B39 : VEN : MICRON | DEV : S0J9K9 : RAM : [ 4.00 GB ]
EMI : [07] : eMMC : LP_DDR4X : ID : 150100444836444142 : VEN : SAMSUNG | DEV : DH6DAB : RAM : [ 4.00 GB ]
EMI : [08] : eMMC : LP_DDR4X : ID : 90014A68433861503E : VEN : HYNIX | DEV : hC8aP> : RAM : [ 4.00 GB ]
EMI : [09] : eUFS : LP_DDR4X : DEV : MT128GASAO4U21 : RAM : [ 6.00 GB ]
EMI : [0A] : eUFS : LP_DDR4X : DEV : MT128GASAO4U21 : RAM : [ 8.00 GB ]
EMI : [0B] : eMMC : LP_DDR4X : ID : 13014E53304A394B38 : VEN : MICRON | DEV : S0J9K8 : RAM : [ 4.00 GB ]
EMI : [0C] : eMMC : LP_DDR4X : ID : 13014E53304A394D39 : VEN : MICRON | DEV : S0J9M9 : RAM : [ 6.00 GB ]
EMI : [0D] : eMMC : LP_DDR4X : ID : 13014E53304A394438 : VEN : MICRON | DEV : S0J9D8 : RAM : [ 4.00 GB ]
EMI : [0E] : eUFS : LP_DDR4X : DEV : KM2B8001CM-BB01 : RAM : [ 6.00 GB ]
EMI : [0F] : eMMC : LP_DDR4X : ID : 450100444134313238 : VEN : SANDISK | DEV : DA4128 : RAM : [ 4.00 GB ]
EMI : [10] : eUFS : LP_DDR4X : DEV : KM8V7001JM-B810 : RAM : [ 8.00 GB ]
EMI : [11] : eUFS : LP_DDR4X : DEV : KM2V8001CM-B707 : RAM : [ 6.00 GB ]
EMI : [12] : eUFS : LP_DDR4X : DEV : KM8B8001JM-BC01 : RAM : [ 8.00 GB ]
EMI : [13] : eUFS : LP_DDR4X : DEV : H9HQ22AECMMDAR : RAM : [ 6.00 GB ]
EMI : [14] : eUFS : LP_DDR4X : DEV : KM8V8001JM-B813 : RAM : [ 8.00 GB ]
EMI : [15] : eUFS : LP_DDR4X : DEV : MT128GASAO4U21 : RAM : [ 4.00 GB ]
EMI : [16] : eUFS : LP_DDR4X : DEV : H28S8Q302CMR : RAM : [ 6.00 GB ]
EMI : [17] : eUFS : LP_DDR4X : DEV : H9HQ16AFAMMDAR : RAM : [ 8.00 GB ]
EMI : [18] : eUFS : LP_DDR4X : DEV : H9HQ22AFAMMDAR : RAM : [ 8.00 GB ]
EMI : [19] : DRAM : LP_DDR4X : ID : NOT_DEFINED : VEN : UNKNOWN | DEV : : RAM : [ 6.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00039000 [ 228.00 KB ]
DRAM: 0x200000000 [ 8.00 GB ]

UFS: AD014839485131364146414D4D444152
UFS:
VEN : 0x01AD
VID : H9HQ16AFAMMDAR
IFW : A107
LU0 : 0x00400000 [ 4.00 MB ]
LU1 : 0x00400000 [ 4.00 MB ]
LU2 : 0x1DCB000000 [ 119.17 GB ]
FSN : 158e4dceab23000000000000
REG : 0x101010000

CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 86110B05DC77D41038316A276128B5A8

DA : USB : HIGH-SPEED

Boot done!

Patch Level : QP1A.190711.020
Display ID : QP1A.190711.020 release-keys
Ver. CodeName : REL
Ver. Release : 10
Sec. Patch : 2020-12-05
Build Time : 20.11.2020
Product Info : oppo6771


STORAGE : LifeStatus : UFS : OK!

Done!
Elapsed: 00:00:28
Operation : Reset Settings/Format FS [ v2.20 ]
Mode : SMART RESET
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port_V1632 (COM131)
MODE : BOOTROM
PORT : 131
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Sylvia
TYPE : MODERN RAPHAEL
BROM : MEID : 7FEE66FC1208C993D72BF02714AB1F50
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : Oppo : F11-Reno2F | Manual : Disabled
BROM : SOCID : 762D23CDCF8395B8B52A88FAFC11CF88FBCBEBFE9F99BED79C 19AF8AD3780892
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6771
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6752
EMI : SRC : preloader_oppo6771.bin
EMI : CNT : 001A
EMI : [00] : eMMC : LP_DDR4X : ID : 150100445636444D42 : VEN : SAMSUNG | DEV : DV6DMB : RAM : [ 4.00 GB ]
EMI : [01] : eUFS : LP_DDR4X : DEV : KM5V8001DM-B622 : RAM : [ 4.00 GB ]
EMI : [02] : eMMC : LP_DDR4X : ID : 150100335636434D42 : VEN : SAMSUNG | DEV : 3V6CMB : RAM : [ 6.00 GB ]
EMI : [03] : eUFS : LP_DDR4X : DEV : KM5V7001DM-B621 : RAM : [ 4.00 GB ]
EMI : [04] : eMMC : LP_DDR4X : ID : 150100334836434142 : VEN : SAMSUNG | DEV : 3H6CAB : RAM : [ 6.00 GB ]
EMI : [05] : eMMC : LP_DDR4X : ID : 90014A68433861503E : VEN : HYNIX | DEV : hC8aP> : RAM : [ 6.00 GB ]
EMI : [06] : eMMC : LP_DDR4X : ID : 13014E53304A394B39 : VEN : MICRON | DEV : S0J9K9 : RAM : [ 4.00 GB ]
EMI : [07] : eMMC : LP_DDR4X : ID : 150100444836444142 : VEN : SAMSUNG | DEV : DH6DAB : RAM : [ 4.00 GB ]
EMI : [08] : eMMC : LP_DDR4X : ID : 90014A68433861503E : VEN : HYNIX | DEV : hC8aP> : RAM : [ 4.00 GB ]
EMI : [09] : eUFS : LP_DDR4X : DEV : MT128GASAO4U21 : RAM : [ 6.00 GB ]
EMI : [0A] : eUFS : LP_DDR4X : DEV : MT128GASAO4U21 : RAM : [ 8.00 GB ]
EMI : [0B] : eMMC : LP_DDR4X : ID : 13014E53304A394B38 : VEN : MICRON | DEV : S0J9K8 : RAM : [ 4.00 GB ]
EMI : [0C] : eMMC : LP_DDR4X : ID : 13014E53304A394D39 : VEN : MICRON | DEV : S0J9M9 : RAM : [ 6.00 GB ]
EMI : [0D] : eMMC : LP_DDR4X : ID : 13014E53304A394438 : VEN : MICRON | DEV : S0J9D8 : RAM : [ 4.00 GB ]
EMI : [0E] : eUFS : LP_DDR4X : DEV : KM2B8001CM-BB01 : RAM : [ 6.00 GB ]
EMI : [0F] : eMMC : LP_DDR4X : ID : 450100444134313238 : VEN : SANDISK | DEV : DA4128 : RAM : [ 4.00 GB ]
EMI : [10] : eUFS : LP_DDR4X : DEV : KM8V7001JM-B810 : RAM : [ 8.00 GB ]
EMI : [11] : eUFS : LP_DDR4X : DEV : KM2V8001CM-B707 : RAM : [ 6.00 GB ]
EMI : [12] : eUFS : LP_DDR4X : DEV : KM8B8001JM-BC01 : RAM : [ 8.00 GB ]
EMI : [13] : eUFS : LP_DDR4X : DEV : H9HQ22AECMMDAR : RAM : [ 6.00 GB ]
EMI : [14] : eUFS : LP_DDR4X : DEV : KM8V8001JM-B813 : RAM : [ 8.00 GB ]
EMI : [15] : eUFS : LP_DDR4X : DEV : MT128GASAO4U21 : RAM : [ 4.00 GB ]
EMI : [16] : eUFS : LP_DDR4X : DEV : H28S8Q302CMR : RAM : [ 6.00 GB ]
EMI : [17] : eUFS : LP_DDR4X : DEV : H9HQ16AFAMMDAR : RAM : [ 8.00 GB ]
EMI : [18] : eUFS : LP_DDR4X : DEV : H9HQ22AFAMMDAR : RAM : [ 8.00 GB ]
EMI : [19] : DRAM : LP_DDR4X : ID : NOT_DEFINED : VEN : UNKNOWN | DEV : : RAM : [ 6.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00039000 [ 228.00 KB ]
DRAM: 0x200000000 [ 8.00 GB ]

UFS: AD014839485131364146414D4D444152
UFS:
VEN : 0x01AD
VID : H9HQ16AFAMMDAR
IFW : A107
LU0 : 0x00400000 [ 4.00 MB ]
LU1 : 0x00400000 [ 4.00 MB ]
LU2 : 0x1DCB000000 [ 119.17 GB ]
FSN : 158e4dceab23000000000000
REG : 0x101010000

CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 86110B05DC77D41038316A276128B5A8

DA : USB : HIGH-SPEED

Boot done!

SmartInfo : 0x825757

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA

Done!
Elapsed: 00:00:47

Reconnect Power/Cable!