GSM-Forum

GSM-Forum (https://forum.gsmhosting.com/vbb/)
-   Infinity-Box (https://forum.gsmhosting.com/vbb/f296/)
-   -   itel S16 Pro cannot be connected with CM2 (https://forum.gsmhosting.com/vbb/f296/itel-s16-pro-cannot-connected-cm2-2974870/)

leroi2018 06-08-2021 20:57

itel S16 Pro cannot be connected with CM2
 
hi

i try to remove FRP on Itel W6503 S16 Pro without success


Operation : Format FS / Reset Settings [ v2.12 ]
Mode : Default [ Reset Settings + FRP ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_2GB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
>>> ERROR : FDL NOT started!

>>> Error : Fail to boot FDL!
>>> Unsupported device with selected fdl or settings! Change settings!

Reconnect Power/Cable!

Operation : Identify [ v2.12 ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC7731E_BASE : SC7731E_eMMC_1GB_0S
Sending Init Boot ...
Boot sent!
Kick FDL ...
>>> ERROR : FDL NOT started!

>>> Error : Fail to boot FDL!
>>> Unsupported device with selected fdl or settings! Change settings!

Reconnect Power/Cable!

Operation : Format FS / Reset Settings [ v2.12 ]
Mode : Default [ Reset Settings + FRP ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
>>> ERROR : Protocol HandShake failed!

>>> Error : Fail to init protocol!
>>> Remove battery, cable. Check cable and connection. Repeat operation!

Reconnect Power/Cable!

Operation : Format FS / Reset Settings [ v2.12 ]
Mode : Default [ Reset Settings + FRP ]
BootMode : FLASH

Card found : 21B1154E , v0148
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.12

Load IDBase v8331 Ok!


Operation : Format FS / Reset Settings [ v2.12 ]
Mode : Default [ Reset Settings + FRP ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC9863x_BASE : SC9863_eMMC_2GB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
>>> ERROR : FDL NOT started!

>>> Error : Fail to boot FDL!
>>> Unsupported device with selected fdl or settings! Change settings!

Reconnect Power/Cable!

Operation : Format FS / Reset Settings [ v2.12 ]
Mode : Default [ Reset Settings + FRP ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC9863x_BASE : SC9863_eMMC_2GB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
>>> ERROR : FDL NOT started!

>>> Error : Fail to boot FDL!
>>> Unsupported device with selected fdl or settings! Change settings!

Reconnect Power/Cable!

Operation : Format FS / Reset Settings [ v2.12 ]
Mode : Default [ Reset Settings + FRP ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : 0_SC9863x_BASE : SC9863_eMMC_2GB_RS
Sending Init Boot ...
Boot sent!
Kick FDL ...
>>> ERROR : FDL NOT started!

>>> Error : Fail to boot FDL!
>>> Unsupported device with selected fdl or settings! Change settings!

Reconnect Power/Cable!

so i wnat to know if infinity support this phone

Yusuf Lawal 06-08-2021 22:29

To know the correct boot, 1s of all connect phone in diag mode.

JayDi 06-09-2021 08:52

Itel mostly uses OWN sign keys, so connect as ITEL.

mmtheo 06-09-2021 18:52

Quote:

Originally Posted by Yusuf Lawal (Post 14407624)
To know the correct boot, 1s of all connect phone in diag mode.

S16 is a signed phone so even he read the phone in diag it won't mean a thing, the only option for him is to use pac file in cm2spd2 to service his phone, i hope team will add itel, mobicel and tecno spd phones soon

JayDi 06-09-2021 20:25

Quote:

Originally Posted by mmtheo (Post 14408193)
S16 is a signed phone so even he read the phone in diag it won't mean a thing, the only option for him is to use pac file in cm2spd2 to service his phone, i hope team will add itel, mobicel and tecno spd phones soon

What? Itel and rest already in list.


https://forum.gsmhosting.com/vbb/14407864-post37.html

leroi2018 06-10-2021 05:40

itel S16 PRO W6503 CORRECT STEP TO REMOVE FRP
 
Quote:

Originally Posted by JayDi (Post 14408213)
What? Itel and rest already in list.


https://forum.gsmhosting.com/vbb/14407864-post37.html

Hi Sir JayDi

below link discussion is regarding flash of itel S16 W6502 not remove FRP on Itel S16 Pro W6503, i found flash file of S16 Pro W6503; so i want to know how to remove FRP on this itel W6503, using flash file which is on support.

thanks for your help
regards

leroi2018 06-10-2021 05:50

Hi Jaydi

on above post is regarding flash of itel S16 W6502 wich will be supported by next update 2.13.

My question is about itel S16 pro W6503 with FRP

i found flash file on support ; so please i would like to know how to remove FRP on this phone using current firmware which is on support

thanks for your explanation

regards
leroi

leroi2018 06-10-2021 05:56

Quote:

Originally Posted by JayDi (Post 14407840)
Itel mostly uses OWN sign keys, so connect as ITEL.

Hi

thanks for your advices, but on current 2.12 version there is not any W6503 option to services on Itel Tab

JayDi 06-10-2021 07:07

Quote:

Originally Posted by leroi2018 (Post 14408300)
Hi

thanks for your advices, but on current 2.12 version there is not any W6503 option to services on Itel Tab

Link to test version has been sent in PM.

Tanha0321 06-10-2021 08:56

ZTE Z3 First Time Cannect 2nd Time Not Cannect
 
Code:

Patch Level    : PPR1.180610.011
Display ID    : PK_ZONGZ3_A5_2019_V1.0
Ver. Incmt    : 20191224.142013
Ver. CodeName  : REL
Ver. Release  : 9
Sec. Patch    : 2019-12-05
Build Time    : 24.12.2019
Product Model  : Z3
Product Brand  : ZTE
Product Name  : P963F30P
Product Device : P963F30P
Product Manfct : ZTE
Product Info  : P963F30P
Product Name  : s9863a1h10_Natv
Product Device : s9863a1h10
Product Board  : lucyzh64
Board Platform : sp9863a


Platform Version: MOCORTM_18B_W19.10.2_ZLA_P16_Debug
Project Version:  sharkl3_pub
BASE  Version:    FM_BASE_18B_W19.10.2_ZLA_P16
HW Version:        sc9863A_modem
CMP_Time : 11-19-2019 18:08:48

MODEM TAG : MOCORTM_18B_W19.10.2_ZLA_P16_Debug_FM_BASE_18B_W19.10.2_ZLA_P16_sc9863A_modem_sharkl3_pub

USERDATA : FILESYSTEM : F2FS  with FDE ( Full Disk Encryption ***)

 - > INFO : Remove cable from device to switch it off!

Done!
Elapsed: 00:02:02




Code:

Operation : Identify [ v2.12 ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : INFINITY FW PACKAGE
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
>>>  ERROR : FLASH FDL NOT started!

>>>  Error : Fail to boot FDL!
>>>  Unsupported device with selected fdl or settings! Change settings!

Reconnect Power/Cable!


JayDi 06-10-2021 09:21

Quote:

Originally Posted by Tanha0321 (Post 14408376)
Code:

Patch Level    : PPR1.180610.011
Display ID    : PK_ZONGZ3_A5_2019_V1.0
Ver. Incmt    : 20191224.142013
Ver. CodeName  : REL
Ver. Release  : 9
Sec. Patch    : 2019-12-05
Build Time    : 24.12.2019
Product Model  : Z3
Product Brand  : ZTE
Product Name  : P963F30P
Product Device : P963F30P
Product Manfct : ZTE
Product Info  : P963F30P
Product Name  : s9863a1h10_Natv
Product Device : s9863a1h10
Product Board  : lucyzh64
Board Platform : sp9863a


Platform Version: MOCORTM_18B_W19.10.2_ZLA_P16_Debug
Project Version:  sharkl3_pub
BASE  Version:    FM_BASE_18B_W19.10.2_ZLA_P16
HW Version:        sc9863A_modem
CMP_Time : 11-19-2019 18:08:48

MODEM TAG : MOCORTM_18B_W19.10.2_ZLA_P16_Debug_FM_BASE_18B_W19.10.2_ZLA_P16_sc9863A_modem_sharkl3_pub

USERDATA : FILESYSTEM : F2FS  with FDE ( Full Disk Encryption ***)

 - > INFO : Remove cable from device to switch it off!

Done!
Elapsed: 00:02:02


Code:

Operation : Identify [ v2.12 ]
BootMode : FLASH

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : INFINITY FW PACKAGE
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
>>>  ERROR : FLASH FDL NOT started!

>>>  Error : Fail to boot FDL!
>>>  Unsupported device with selected fdl or settings! Change settings!

Reconnect Power/Cable!


Always post complete logs, because have no idea about FIRST settings and then see other ones.

Tanha0321 06-10-2021 11:00

How To Setting Change
 
Code:

Patch Level    : PPR1.180610.011
Display ID    : PK_ZONGZ3_A5_2019_V1.0
Ver. Incmt    : 20191224.142013
Ver. CodeName  : REL
Ver. Release  : 9
Sec. Patch    : 2019-12-05
Build Time    : 24.12.2019
Product Model  : Z3
Product Brand  : ZTE
Product Name  : P963F30P
Product Device : P963F30P
Product Manfct : ZTE
Product Info  : P963F30P
Product Name  : s9863a1h10_Natv
Product Device : s9863a1h10
Product Board  : lucyzh64
Board Platform : sp9863a


Platform Version: MOCORTM_18B_W19.10.2_ZLA_P16_Debug
Project Version:  sharkl3_pub
BASE  Version:    FM_BASE_18B_W19.10.2_ZLA_P16
HW Version:        sc9863A_modem
CMP_Time : 11-19-2019 18:08:48

MODEM TAG : MOCORTM_18B_W19.10.2_ZLA_P16_Debug_FM_BASE_18B_W19.10.2_ZLA_P16_sc9863A_modem_sharkl3_pub

USERDATA : FILESYSTEM : F2FS  with FDE ( Full Disk Encryption ***)

 - > INFO : Remove cable from device to switch it off!

Done!
Elapsed: 00:01:23

Open : SPD_PROG.xml
Reading package ...
Read package finished!

Created by Infinity-Box (c) 2020
Chinese Miracle II : Spreadtrum / UniSoc Service Module
Device Info file  : _Android_info.txt

Patch Level    : PPR1.180610.011
Display ID    : PK_ZONGZ3_A5_2019_V1.0
Ver. Incmt    : 20191224.142013
Ver. CodeName  : REL
Ver. Release  : 9
Sec. Patch    : 2019-12-05
Build Time    : 24.12.2019
Product Model  : Z3
Product Brand  : ZTE
Product Name  : P963F30P
Product Device : P963F30P
Product Manfct : ZTE
Product Info  : P963F30P
Product Name  : s9863a1h10_Natv
Product Device : s9863a1h10
Product Board  : lucyzh64
Board Platform : sp9863a

SECSolution : MODERN [RS/0S/1S/2S]


Operation : Flash Firmware [ v2.12 ]

Setting  : Update NVRAM : False
Setting  : Force NVRAM : False
Setting  : Update PMT  : True

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : INF : INFINITY FW PACKAGE
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
>>>  ERROR : FLASH FDL NOT started!

>>>  Error : Fail to boot FDL!
>>>  Unsupported device with selected fdl or settings! Change settings!

Reconnect Power/Cable!


leroi2018 06-10-2021 15:32

Quote:

Originally Posted by JayDi (Post 14408322)
Link to test version has been sent in PM.

hi Sir Jaydi

i did not received the soft via PM.

regards
leroi

simeon uche 01-18-2022 01:59

Quote:

Originally Posted by JayDi (Post 14408213)
What? Itel and rest already in list.


https://forum.gsmhosting.com/vbb/14407864-post37.html

Which boot did you sellet sir

InfinityHelp 01-18-2022 19:27

Quote:

Originally Posted by simeon uche (Post 14505872)
Which boot did you sellet sir

loader file is at Infinity support area iTel_S16_Pro_W6503_FDL

simeon uche 01-25-2022 00:59

Quote:

Originally Posted by JayDi (Post 14408213)
What? Itel and rest already in list.


https://forum.gsmhosting.com/vbb/14407864-post37.html

Which boot did you select sir as

Freeboy08 03-03-2022 16:39

1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!

Wait for device ...

Device Connected!
BootVersion : SPRD3
Boot : MANUAL LDR
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0020
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!

Boot Done!

Wipe Ok : FRP


https://www.youtube.com/watch?v=gNkcUYTI1YE


All times are GMT +1. The time now is 23:34.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2022 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2017 -

Page generated in 0.18455 seconds with 6 queries

SEO by vBSEO