Tecno Kc2 flash problem. - GSM-Forum

Amman602 · 08-10-2020, 11:25

Operation : Identify [ v2.14 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM75)
MODE : BOOTROM
PORT : 75
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6761 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0200
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+ARB
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : TECNO : SECURE_v2 | Manual : Disabled
BROM : SOCID : 28C5C369CBD5E4115E63079867F90F132CC0DB52326FD0E8D0 8543A8CA48B6C5
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 4002 0000 [0200] F3: 1006 0033 F3: 4001 00E0 00: 1005 0000 F3: 4002 0000 [0200] F3: 4001 00E0 01: 102A 0001
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_SWSEC.bin
AGENT : Found MT6761
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...

BROM : 0x00007017 : DA SEND ERROR!
ERROR : SECURE BOOT : SLA REQUIRED IN BROM MODE!
INFO : BROM Level : CERT/AUTH required! Try boot device in PRELOADER mode with select PL/PL_CRYPTO/SWSEC type!

Error : Fail to init protocol!
>>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation!

Reconnect Power/Cable!

08-10-2020, 11:25	#1 (permalink)
Amman602 Freak Poster Join Date: Dec 2018 Location: Gujrat Posts: 124 Member: 2882521 Status: Offline Thanks Meter: 34	Tecno Kc2 flash problem. Operation : Identify [ v2.14 ] Mode : FLASH 1. Make sure device is powered off. Power off, if need. Wait 20 seconds after 2. Insert USB cable in phone Waiting for device connection ... PTFN : MediaTek USB Port (COM75) MODE : BOOTROM PORT : 75 Waiting BOOT ack ... BROM : Skip ACK verify BROM : Init BROM BROM init passed! CHIP : MT6761 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0200 TYPE : MODERN RAPHAEL BROM : SecLevel : 0x000000E5 BROM : SecMode : SBC+SDA+ARB BROM : BROM\|BL : 0x05\|0xFE BROM : BOOTROM MODE : TECNO : SECURE_v2 \| Manual : Disabled BROM : SOCID : 28C5C369CBD5E4115E63079867F90F132CC0DB52326FD0E8D0 8543A8CA48B6C5 BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 4002 0000 [0200] F3: 1006 0033 F3: 4001 00E0 00: 1005 0000 F3: 4002 0000 [0200] F3: 4001 00E0 01: 102A 0001 AGENT : Look for suitable BootChain in DA ... AGENT : MTK_AllInOne_DA_SWSEC.bin AGENT : Found MT6761 AGENT : MTK_DOWNLOAD_AGENT BROM : Sending 1st DA ... BROM : 0x00007017 : DA SEND ERROR! ERROR : SECURE BOOT : SLA REQUIRED IN BROM MODE! INFO : BROM Level : CERT/AUTH required! Try boot device in PRELOADER mode with select PL/PL_CRYPTO/SWSEC type! Error : Fail to init protocol! >>> Remove battery, cable. Check cable/connection/driver! Check SW hint! Repeat operation! Reconnect Power/Cable!