Repair of dead C25/C28 v.61 finally !!!! - Page 4 - GSM-Forum

andel · 01-25-2003, 20:27

Here is a working link :
http://www.unlock.times.lv/soft/siemens/x25unlock.htm
the page is a litle bit slow.

gokhanalpaslan · 01-28-2003, 11:10

i checked your link but files are does not request how can i get them???

Own · 01-29-2003, 11:23

Hi.....gokhanalpaslan

contact me by ICQ i give you all [if you want]
Thnx
Own

my ICQ = 166679430

ACDC · 01-30-2003, 12:05

Hi!

When I start this program all I get is ' Sending boots ' and it stops here.

Before that it stops on ' Scanning ' then I pres power on and I get ' Sending boots '. It stops 'till I pres STOP.

What is this?
I'm using AutoIgnition cable!

gokhanalpaslan · 01-30-2003, 23:11

sometimes it does just remove battery and try again
however i found maxim at last and my c28 working now

jtdc · 02-11-2003, 13:53

finally, a very helpful thread. however, i can't download onto any of the posted links.

i have 2 units C25 that had been sleeping and awaiting solution for more than a year now. one is originally ver49 and the other ver51 when they were working... before they died.

i have c25_61 flash which runs under C25 total flasher, and it flashes the phone successfully. now, both phones display 'Wrong Softw.'. so then i ran C25_eeprom (DOS mode) and now both phone loads up.

however, when i put SIM on the unit, one of them doesn't acquire network signal... keeps on searching. the other one, after booting and detecting the SIM, the phone turns off by itself.

any ideas what to do next?

COMPAQ · 02-11-2003, 17:53

SOMEONE PLS SEND ME FLASH FILE FOR MAXIM SOFTWARE@[email protected]

Own · 02-11-2003, 19:00

only flash file
contact my ICQ
Own

gokhanalpaslan · 02-11-2003, 22:56

i can send u software contact me on icq 57222325

jtdc · 02-12-2003, 04:01

hi Own and gokhanalpaslan. unfortunately, though i have ICQ, i don't run it anymore. would you be kind enough to send it to my email [email protected]

thanks in advance... i hope these two phones resurrect.

garouppa · 03-05-2003, 01:36

i think i'm the last one with a dead c28v61, the maxim soft looks like working, sending stuff, reading imei etc, but i really need very badly a full flash, and i donnow anything about the adresses i should be utting there

for g/d sake ...please HELP !!!!

rajul32 · 04-08-2003, 16:09

I AM NOT ABLE TO DOWNLOAD THE SOFT FROM SITE DINGO.SYS-PRO.COM
USER NAME?
PASSWORD?

gokhanalpaslan · 04-09-2003, 17:07

you can download c28 v61 repair and unlock tool from here
<a href="http://www.cepklinik.com">www.cepklinik.com</a>
this site is turkish just go download section u will see C25_repair_&_unlock_v61 click on it thats all

i tested it it works %100000

Mr.Fl@sher · 04-13-2003, 21:00

plz wht the right flash address
tried with 0000-0000
0100-0000
no way

plz urgent

arti123a · 05-27-2003, 18:04

please send me flash for maxim program

01-25-2003, 20:27	#46 (permalink)
andel Junior Member Join Date: Jan 2003 Posts: 2 Member: 20357 Status: Offline Thanks Meter: 0	solution !! Here is a working link : http://www.unlock.times.lv/soft/siemens/x25unlock.htm the page is a litle bit slow.

01-29-2003, 11:23	#48 (permalink)
Own No Life Poster Join Date: Aug 2001 Location: Minsk Russia Posts: 915 Member: 5569 Status: Offline Thanks Meter: 10	ICQ Hi.....gokhanalpaslan contact me by ICQ i give you all [if you want] Thnx Own my ICQ = 166679430

02-11-2003, 19:00	#53 (permalink)
Own No Life Poster Join Date: Aug 2001 Location: Minsk Russia Posts: 915 Member: 5569 Status: Offline Thanks Meter: 10	only flash file only flash file contact my ICQ Own

03-05-2003, 01:36	#56 (permalink)
garouppa Junior Member Join Date: Mar 2003 Age: 53 Posts: 1 Member: 23874 Status: Offline Thanks Meter: 0	the last one stuck with his own private c28 i think i'm the last one with a dead c28v61, the maxim soft looks like working, sending stuff, reading imei etc, but i really need very badly a full flash, and i donnow anything about the adresses i should be utting there for g/d sake ...please HELP !!!!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Repair for dead C25 v.61 need (bad unlocker)	roller	x1x to x45/x50	2	09-12-2001 20:50
C25/C28 vers 61 PHONE LOCK CODE Solution	ed2k_7	x1x to x45/x50	0	07-07-2001 14:37
search link-Siemens C25/C28 Ver.61 Service Software Ver. 2.5	Baza	GSM Mobile Links	2	04-05-2001 20:04
andromeda C25/C28 Ver.61 S-Software Ver. 2.5	Baza	x1x to x45/x50	5	03-28-2001 00:29
Simens c25/c28 ver.61 unlocker for all - free	Deni	x1x to x45/x50	2	12-02-2000 15:04

01-28-2003, 11:10	#47 (permalink)
gokhanalpaslan Insane Poster Join Date: Jan 2003 Location: izmir/turkey Age: 45 Posts: 99 Member: 19907 Status: Offline Thanks Meter: 0	i checked your link but files are does not request how can i get them???

01-30-2003, 12:05	#49 (permalink)
ACDC Junior Member Join Date: Jan 2003 Posts: 5 Member: 20293 Status: Offline Thanks Meter: 0	Hi! When I start this program all I get is ' Sending boots ' and it stops here. Before that it stops on ' Scanning ' then I pres power on and I get ' Sending boots '. It stops 'till I pres STOP. What is this? I'm using AutoIgnition cable!

01-30-2003, 23:11	#50 (permalink)
gokhanalpaslan Insane Poster Join Date: Jan 2003 Location: izmir/turkey Age: 45 Posts: 99 Member: 19907 Status: Offline Thanks Meter: 0	sometimes it does just remove battery and try again however i found maxim at last and my c28 working now

02-11-2003, 13:53	#51 (permalink)
jtdc Junior Member Join Date: Feb 2003 Location: Manila, Philippines Age: 45 Posts: 9 Member: 21384 Status: Offline Thanks Meter: 0	finally, a very helpful thread. however, i can't download onto any of the posted links. i have 2 units C25 that had been sleeping and awaiting solution for more than a year now. one is originally ver49 and the other ver51 when they were working... before they died. i have c25_61 flash which runs under C25 total flasher, and it flashes the phone successfully. now, both phones display 'Wrong Softw.'. so then i ran C25_eeprom (DOS mode) and now both phone loads up. however, when i put SIM on the unit, one of them doesn't acquire network signal... keeps on searching. the other one, after booting and detecting the SIM, the phone turns off by itself. any ideas what to do next?

02-11-2003, 17:53	#52 (permalink)
COMPAQ No Life Poster Join Date: Dec 2002 Location: INDIA Age: 45 Posts: 528 Member: 18462 Status: Offline Thanks Meter: 30	SOMEONE PLS SEND ME FLASH FILE FOR MAXIM SOFTWARE@[email protected]

02-11-2003, 22:56	#54 (permalink)
gokhanalpaslan Insane Poster Join Date: Jan 2003 Location: izmir/turkey Age: 45 Posts: 99 Member: 19907 Status: Offline Thanks Meter: 0	i can send u software contact me on icq 57222325

02-12-2003, 04:01	#55 (permalink)
jtdc Junior Member Join Date: Feb 2003 Location: Manila, Philippines Age: 45 Posts: 9 Member: 21384 Status: Offline Thanks Meter: 0	hi Own and gokhanalpaslan. unfortunately, though i have ICQ, i don't run it anymore. would you be kind enough to send it to my email [email protected] thanks in advance... i hope these two phones resurrect.

04-08-2003, 16:09	#57 (permalink)
rajul32 Freak Poster Join Date: Nov 2002 Location: 1lucknow Age: 55 Posts: 125 Member: 18218 Status: Offline Thanks Meter: 2	I AM NOT ABLE TO DOWNLOAD THE SOFT FROM SITE DINGO.SYS-PRO.COM USER NAME? PASSWORD?

04-09-2003, 17:07	#58 (permalink)
gokhanalpaslan Insane Poster Join Date: Jan 2003 Location: izmir/turkey Age: 45 Posts: 99 Member: 19907 Status: Offline Thanks Meter: 0	you can download c28 v61 repair and unlock tool from here <a href="http://www.cepklinik.com">www.cepklinik.com</a> this site is turkish just go download section u will see C25_repair_&_unlock_v61 click on it thats all i tested it it works %100000

04-13-2003, 21:00	#59 (permalink)
Mr.Fl@sher Freak Poster Join Date: Nov 2002 Location: Use Browser !!! Age: 44 Posts: 401 Member: 17798 Status: Offline Sonork: 100.62007 Thanks Meter: 9	plz wht the right flash address tried with 0000-0000 0100-0000 no way plz urgent

05-27-2003, 18:04	#60 (permalink)
arti123a Freak Poster Join Date: Jan 2002 Location: Poland Age: 50 Posts: 274 Member: 8537 Status: Offline Thanks Meter: 7	please send me flash for maxim program