GSM-Forum
Page 1 of 3 1 23
Show 50 post(s) from this thread on one page

GSM-Forum (https://forum.gsmhosting.com/vbb/)
-   BB5 Easy Service Tool (BEST) Nokia Dongle (https://forum.gsmhosting.com/vbb/f641/)
-   -   Nokia 5310 (2020) Test (https://forum.gsmhosting.com/vbb/f641/nokia-5310-2020-test-2895837/)

JayDi 09-06-2020 20:05
Nokia 5310 (2020) Test
 
Code:
Operation : Identify [ v1.21 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM22)
MODE : NOKIA USB SERIAL
PORT : 22
BROM : Init BROM
BROM init passed!
    CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 07xxxxxxxxxxxxxxxxxxxxxxxx
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : PISCES.10.01.11.p1
BOOT : SWR : 10.01.11
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : PISCES.10.01.11.p1
FLASH : 00EF : 0060 : 0018 : 0000
PRDC : 059Z0X8
IMEI[1] : 35xxxxxxxxxxx
IMEI[2] : 35xxxxxxxxxxx
NCK  : 20 digits
PROV : 24407000

Saved as  : 35xxxxxxxxxxxx.mtsec
Saved to  : C:\Infinity-Box\BEST2\Backup\


Done!
Elapsed: 00:00:24

 Reconnect Power/Cable!

Code:

Operation : Read FirmWare [ v1.21 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM22)
MODE : NOKIA USB SERIAL
PORT : 22
BROM : Init BROM
BROM init passed!
    CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 07xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : PISCES.10.01.11.p1
BOOT : SWR : 10.01.11
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : PISCES.10.01.11.p1
FLASH : 00EF : 0060 : 0018 : 0000
CODE  : 0x00C40000
Reading Flash ...
TDSN : TA-1212
PRDC : 059Z0X8
PPM  : EI
LANG :
[1] : Georgian (Georgia)
[2] : Armenian (Armenia)
[3] : Romanian (Romania)
[4] : Ukrainian (Ukraine)
[5] : Belarusian (Belarus)
[6] : Uzbek (Uzbekistan)
[7] : Russian (Russia)
[8] : Kazakh (Kazakhstan)
[9] : Azeri (Azerbaijan)
[10] : English (United Kingdom)

BUILD : TA-1212_ROM_eMP_10.01.11
BUILD : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
BUILD : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
BUILD : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
BUILD : TA-1212_VIVA_eMP_10.01.11

Make VPL definition

Save Path : C:\Nokia\FP\TA-1212\
Save Name : TA-1212_059Z0X8_10.01.11.vpl

Build Finished!

Done!
Elapsed: 00:06:00
Code:

Open VPLfile : TA-1212_059Z0X8_10.01.11.vpl
Description  : TA-1212 EI
DeviceType  : TA-1212
ProductCode  : 059Z0X8
SoftwareVer  : 10.01.11
Load Ok!

Operation : Write FirmWare [ v1.21 ]
Setting  : UserData erase : True
Setting  : LangPack Only : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM22)
MODE : NOKIA USB SERIAL
PORT : 22
BROM : Init BROM
BROM init passed!
    CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 07xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : PISCES.10.01.11.p1
BOOT : SWR : 10.01.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : PISCES.10.01.11.p1
    BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8B

        NOR: 00C8 : 0060 : 0018 : 0000
        NOR: [GigaDevice] GD25LQ128
        NOR:
              TSIZE  : 0x01000000 [ 16,00 MB ]
              PSIZE  : 0x01000000 [ 16,00 MB ]
              STYPE  : 0x00000000
              FLOTP  : DA_NOR_OTP_NOT_SUPPORT

 STATUS : OK
 BSTYLE : SF_FLASH_BOOT

Boot done!

VPL SoftwareVersion  : 10.01.11 [TA-1212]
DEV SoftwareVersion  : 10.01.11
SWInfo compare result : SAME

Load FlashSet :
MROM : TA-1212_ROM_eMP_10.01.11
LANG : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
CUST : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
JUMP : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
VIVA : TA-1212_VIVA_eMP_10.01.11

Prepare FlashSet :
DCR : TA-1212_ROM_eMP_10.01.11
DCR : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
DCR : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
DCR : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
DCR : TA-1212_VIVA_eMP_10.01.11

Prepare Target
SDS : OK : 0x00FF4000 : 0x0000C000
FFS Format Ok!

Erase Target Flash
Erase done!

Write Target Flash
Write : TA-1212_ROM_eMP_10.01.11
Write : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
Write : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
Write : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
Write : TA-1212_VIVA_eMP_10.01.11
Write done, waiting target response ...
Write flash done!

Verify Target FlashContent
Verify : TA-1212_ROM_eMP_10.01.11
Verify : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
Verify : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
Verify : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
Verify : TA-1212_VIVA_eMP_10.01.11

Done!
Elapsed: 00:02:36

 Reconnect Power/Cable!

Code:
Operation : Reset Settings [ v1.21 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM22)
MODE : NOKIA USB SERIAL
PORT : 22
BROM : Init BROM
BROM init passed!
    CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 07xxxxxxxxxxxxxxxx
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : PISCES.10.01.11.p1
BOOT : SWR : 10.01.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : PISCES.10.01.11.p1
    BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8B

        NOR: 00C8 : 0060 : 0018 : 0000
        NOR: [GigaDevice] GD25LQ128
        NOR:
              TSIZE  : 0x01000000 [ 16,00 MB ]
              PSIZE  : 0x01000000 [ 16,00 MB ]
              STYPE  : 0x00000000
              FLOTP  : DA_NOR_OTP_NOT_SUPPORT

 STATUS : OK
 BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00C40000  :  0x003B4000
FFS Format ...
FFS Format Ok!

Done!
 Elapsed: 00:00:28

JayDi 09-06-2020 20:07
On spoiler rights :

Further bonus stuff : identify SW version ( original device, even flashed )



Further bonus stuff : Downgrade/Upgrade SW version on all devices



Further bonus stuff : SWP for repair more devices and cross

Yasir Ali 09-06-2020 21:24
after update support this one???????
https://forum.gsmhosting.com/vbb/f64...shing-2895660/

biochemistali 10-04-2020 09:26
need flash file for TA 1212
 
need flash file for TA 1212
Quote:
Originally Posted by JayDi (Post 14208428)
Code:
Operation : Identify [ v1.21 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM22)
MODE : NOKIA USB SERIAL
PORT : 22
BROM : Init BROM
BROM init passed!
    CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 07xxxxxxxxxxxxxxxxxxxxxxxx
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : PISCES.10.01.11.p1
BOOT : SWR : 10.01.11
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : PISCES.10.01.11.p1
FLASH : 00EF : 0060 : 0018 : 0000
PRDC : 059Z0X8
IMEI[1] : 35xxxxxxxxxxx
IMEI[2] : 35xxxxxxxxxxx
NCK  : 20 digits
PROV : 24407000

Saved as  : 35xxxxxxxxxxxx.mtsec
Saved to  : C:\Infinity-Box\BEST2\Backup\


Done!
Elapsed: 00:00:24

 Reconnect Power/Cable!

Code:

Operation : Read FirmWare [ v1.21 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM22)
MODE : NOKIA USB SERIAL
PORT : 22
BROM : Init BROM
BROM init passed!
    CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 07xxxxxxxxxxxxxxxxxxxxxxxxxxxxx
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : PISCES.10.01.11.p1
BOOT : SWR : 10.01.11
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : PISCES.10.01.11.p1
FLASH : 00EF : 0060 : 0018 : 0000
CODE  : 0x00C40000
Reading Flash ...
TDSN : TA-1212
PRDC : 059Z0X8
PPM  : EI
LANG :
[1] : Georgian (Georgia)
[2] : Armenian (Armenia)
[3] : Romanian (Romania)
[4] : Ukrainian (Ukraine)
[5] : Belarusian (Belarus)
[6] : Uzbek (Uzbekistan)
[7] : Russian (Russia)
[8] : Kazakh (Kazakhstan)
[9] : Azeri (Azerbaijan)
[10] : English (United Kingdom)

BUILD : TA-1212_ROM_eMP_10.01.11
BUILD : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
BUILD : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
BUILD : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
BUILD : TA-1212_VIVA_eMP_10.01.11

Make VPL definition

Save Path : C:\Nokia\FP\TA-1212\
Save Name : TA-1212_059Z0X8_10.01.11.vpl

Build Finished!

Done!
Elapsed: 00:06:00
Code:

Open VPLfile : TA-1212_059Z0X8_10.01.11.vpl
Description  : TA-1212 EI
DeviceType  : TA-1212
ProductCode  : 059Z0X8
SoftwareVer  : 10.01.11
Load Ok!

Operation : Write FirmWare [ v1.21 ]
Setting  : UserData erase : True
Setting  : LangPack Only : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM22)
MODE : NOKIA USB SERIAL
PORT : 22
BROM : Init BROM
BROM init passed!
    CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 07xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : PISCES.10.01.11.p1
BOOT : SWR : 10.01.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : PISCES.10.01.11.p1
    BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8B

        NOR: 00C8 : 0060 : 0018 : 0000
        NOR: [GigaDevice] GD25LQ128
        NOR:
              TSIZE  : 0x01000000 [ 16,00 MB ]
              PSIZE  : 0x01000000 [ 16,00 MB ]
              STYPE  : 0x00000000
              FLOTP  : DA_NOR_OTP_NOT_SUPPORT

 STATUS : OK
 BSTYLE : SF_FLASH_BOOT

Boot done!

VPL SoftwareVersion  : 10.01.11 [TA-1212]
DEV SoftwareVersion  : 10.01.11
SWInfo compare result : SAME

Load FlashSet :
MROM : TA-1212_ROM_eMP_10.01.11
LANG : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
CUST : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
JUMP : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
VIVA : TA-1212_VIVA_eMP_10.01.11

Prepare FlashSet :
DCR : TA-1212_ROM_eMP_10.01.11
DCR : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
DCR : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
DCR : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
DCR : TA-1212_VIVA_eMP_10.01.11

Prepare Target
SDS : OK : 0x00FF4000 : 0x0000C000
FFS Format Ok!

Erase Target Flash
Erase done!

Write Target Flash
Write : TA-1212_ROM_eMP_10.01.11
Write : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
Write : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
Write : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
Write : TA-1212_VIVA_eMP_10.01.11
Write done, waiting target response ...
Write flash done!

Verify Target FlashContent
Verify : TA-1212_ROM_eMP_10.01.11
Verify : TA-1212_LANG_PACK_ROM_EI_eMP_10.01.11_001
Verify : TA-1212_CUSTPACK_ROM_EI_eMP_10.01.11_001
Verify : TA-1212_JUMP_TABLE_EI_eMP_10.01.11_001
Verify : TA-1212_VIVA_eMP_10.01.11

Done!
Elapsed: 00:02:36

 Reconnect Power/Cable!

Code:
Operation : Reset Settings [ v1.21 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM22)
MODE : NOKIA USB SERIAL
PORT : 22
BROM : Init BROM
BROM init passed!
    CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000005
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 07xxxxxxxxxxxxxxxx
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : PISCES.10.01.11.p1
BOOT : SWR : 10.01.11
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : PISCES.10.01.11.p1
    BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Sync Passed!
DA : Authentification pass!
DA : Agent : v03.02 on BBID : 0x8B

        NOR: 00C8 : 0060 : 0018 : 0000
        NOR: [GigaDevice] GD25LQ128
        NOR:
              TSIZE  : 0x01000000 [ 16,00 MB ]
              PSIZE  : 0x01000000 [ 16,00 MB ]
              STYPE  : 0x00000000
              FLOTP  : DA_NOR_OTP_NOT_SUPPORT

 STATUS : OK
 BSTYLE : SF_FLASH_BOOT

Boot done!

FFS Info exists in MAUI : 0x00C40000  :  0x003B4000
FFS Format ...
FFS Format Ok!

Done!
 Elapsed: 00:00:28

kinogsm 10-05-2020 10:35
Hello.
Where can I find the version 1.21?
Regards

alimbkl 11-08-2020 15:39
Quote:
Originally Posted by JayDi (Post 14208430)
On spoiler rights :

Further bonus stuff : identify SW version ( original device, even flashed )



Further bonus stuff : Downgrade/Upgrade SW version on all devices



Further bonus stuff : SWP for repair more devices and cross
when will be update this version 1.21 ???

babarmughal 11-19-2020 15:41
5 months old logs....
when will release sir ?

JayDi 11-20-2020 17:40
There were full sw rebuild to bring new level of service features. Now it finished and new version under deep testing.

babarmughal 11-23-2020 13:35
thank you dear sir. your work was awesome.

yousaf.awan 02-13-2021 07:13
Update InfinityBox BEST 2.21?

german gsm team 02-13-2021 21:13
Any estimated arrival date of new version?

sky73 04-17-2021 19:15
Any news from this update؟

rubel mia 06-08-2021 20:38
Best2 1.21 Version Need

dre2 06-22-2021 03:13
pls any update?,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

iftikharrana58 06-23-2021 15:19
after 7 month test i think not final new update


All times are GMT +1. The time now is 12:03.
Page 1 of 3 1 23
Show 50 post(s) from this thread on one page


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -

Page generated in 0.31506 seconds with 6 queries

SEO by vBSEO