GSM-Forum - Easy-JTAG Very HOT Update. v1.9.0.5 - KMVTU000LM REPAIR even totay dead emmc :)

GSM-Forum (https://forum.gsmhosting.com/vbb/)

- Easy-Jtag / Easy-Jtag Plus (https://forum.gsmhosting.com/vbb/f672/)

- - Easy-JTAG Very HOT Update. v1.9.0.5 - KMVTU000LM REPAIR even totay dead emmc :) (https://forum.gsmhosting.com/vbb/f672/easy-jtag-very-hot-update-v1-9-0-5-kmvtu000lm-repair-even-totay-dead-emmc-1935674/)

Quote:

Originally Posted by BABAK NURI (Post 10972580)

Hi
Thanks
Reapir 48/50 pcs,yesterday
today repaired 65pc , and i have more than 400pcs....D:)

5000pcs

http://i.gyazo.com/0d4271fe700f034083b27d8b3b12ea58.gif

Quote:

Originally Posted by blang (Post 10972593)

5000pcs

aRE U SHOUR U POST CORRRECT PIC ?

IF YES U HAVE NEW UPDATE FOR THIS EMMC POSTED ON YOUR PIC

NOT KMVTU000LM B503

HEHE

Quote:

Originally Posted by freeman2001 (Post 10972611)

aRE U SHOUR U POST CORRRECT PIC ?

IF YES U HAVE NEW UPDATE FOR THIS EMMC POSTED ON YOUR PIC

NOT KMVTU000LM B503

HEHE

may be - who know
;);););););)

any one make good video.... for repair..

Quote:

Originally Posted by blang (Post 10972615)

may be - who know
;);););););)

i have many phones with same ref in your pic show me tp mybe i can repair it withour remove emmc like i9300 and n7100

wbr

I have a question I own Z3X esta upgrade is possible for me? I Have To Have or activation ?

Quote:

Originally Posted by amdres69 (Post 10972699)

I have a question I own Z3X esta upgrade is possible for me? I Have To Have or activation ?

z3x-box and easy-jtag have different hardware.
no way use easy-jtag software with normal z3x-box.

REPAIR WITH US ONLY FIRST IN THE WORLED

Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 08081007CF5C6F33, ,FW Ver.: 01.52
CMD Pullup Level:2041 mV
CMD Active Level:2072 mV
eMMC Device Information
EMMC CID : 45010053454D3038479020B657075070
EMMC CSD : D00F00320F5903FFFFFFFFFF92404010
EMMC Manufacturer ID: 0045 , OEM ID: 0100
EMMC Date: 05/2013 Rev.0x90
EMMC NAME: SEM08G , S/N: 548820743
EMMC NAME (HEX): 53454D30384700
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: SEM08G_ 548820743_20150302_2145.extcsd
Done.

IM repair san disk emmc ic by this update

thank you My mind ;)

i have i9300 restart problem
product name not have
when i connect got error
can i repair without remove emmc ??
if yes
where is i9300 tp ??

Quote:

Originally Posted by vikboston (Post 10972320)

hi,

this error:
'verifying emmc firmware fail: No error'
happend because you didn't disconnect everything from emmc (all lines : 1.8v, 2.8v, clk, cmd, dat0) before making short tp to gnd !!!!
some current leakege apply from cmd, clk, dat0 box lines and emmc goto wrong state, when disconnect only 1.8/2.8v power lines.
Emmc wrong state cause 'verifying emmc firmware fail: No error'
no error - means no communication error, only firmware update error occurs.

Disconnect everything from emmc, make short tp to gnd, plug emmc power then remove tp to gnd, plug into box, make sure that emmc identify 000000, start update firmware again. Emmc update firmware should be ok this time !!!!!!!!!

don't forget to remove tp to gnd connection before firmware update, because will be same error: 'verifying emmc firmware fail: No error' !!!!!!!!!

regards viktor

thank you victor brother just i post log of conection ;)

Quote:

Originally Posted by fares122 (Post 10972734)

Quote:

Originally Posted by fares122 (Post 10972761)

IM repair san disk emmc ic by this update

thank you My mind ;)

Hi
This update is only for repair KMVTU000LM-B503...what's a related for San-Disk?
As we know San-Disk not have internal configuration and we can't repair at all
-
Can you explain what problem you have before repair ?

Thanks

Quote:

Originally Posted by blang (Post 10972593)

5000pcs

http://i.gyazo.com/0d4271fe700f034083b27d8b3b12ea58.gif

my collection of dead emmc is now going to be alive ;)

please help my in shell not new version
im hoe to download 1.9.0.5 version?

Quote:

Originally Posted by BABAK NURI (Post 10973271)

Agree with above post, and show step2 by step, which TP to connect in ******* Emmc.... etc...