★★★ Post Here All Successfully Repaired Phones by Ultimate Multi Tool ★★★ - Page 172 - GSM-Forum

niloy2007 · 05-03-2017, 12:19

Code:

Device: Samsung Device
Operation: Reset FRP (New Method)
Port: COM64 : SAMSUNG Mobile USB Modem #15
Checking for Device... Found [Normal Mode]
Reading Phone Information... OK
Model: SM-J200G
IMEI: 358427073058730
Software: J200GDDU2APL7/J200GODD2APL7/J200GDDU2APJ2/J200GDDU2APL7
Init Download Mode... OK
Port: COM10 : SAMSUNG Mobile USB Modem
Reading Data from Phone... Done
Chipset: LSI3475 [HiSpeed]
Resetting FRP Lock Data... . Done
Closing Session... Done
---------------- IMPORTANT ----------------
Wait for phone to reboot and turn on fully or TURN ON manually.
Once Phone is completely ON, wait a few minutes and then.
goto Menu > Settings > Backup and Reset and do Factory data Reset.
Elapsed Time: 01:01
[Ultimate Samsung Flasher v1.1]

niloy2007 · 05-03-2017, 12:30

Code:

Operation    : Reset FRP
Checking for existing devices... Found
Port    : COM4
Opening Port... OK
Init Handshake Sequence... OK
Hardware ID    : E1009600 [8909] 00000000
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8909.ufl]... Done
Executing Loader... OK
Hardware    : 8909, eMMC, 8 GB
Payload Info    : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device    : TCL 5054T [msm8909]
Software    : LMY47V release-keys, vCC7-0 [Thu Dec 10 19:06:11 CST 2015]
Android Ver.    : 5.1.1
Resetting FRP Lock... . . Done
Operation Finished.

niloy2007 · 05-03-2017, 13:58

Code:

Operation    : Read Firmware
Checking for existing devices... Found
Port    : COM4
Opening Port... OK
Init Handshake Sequence... OK
Hardware ID    : E1009600 [8909] 00000000
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8909.ufl]... Done
Executing Loader... OK
Hardware    : 8909, eMMC, 8 GB
Payload Info    : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device    : TCL 5054T [msm8909]
Software    : LMY47V release-keys, vCC7-0 [Thu Dec 10 19:06:11 CST 2015]
Android Ver.    : 5.1.1
Reading [modem]... Done
Reading [sbl1]... Done
Reading [sbl1bak]... Done
Reading [rpm]... Done
Reading [rpmbak]... Done
Reading [tz]... Done
Reading [tzbak]... Done
Reading [hyp]... Done
Reading [hypbak]... Done
Reading [sec]... Done
Reading [aboot]... Done
Reading [abootbak]... Done
Reading [boot]... Done
Reading [recovery]... Done
Reading [system]... Done
Reading [persist]... Done
Reading [splash]... Done
Reading [cache]... Done
Reading [misc]... Done
Reading [userdata]... Done
Reading [PrimaryGPT]... Done
Reading [BackupGPT]... Done
Saved to    : C:\UMTool\QcFire\Read\5054T_LMY47V release-keys_5.1.1\
Operation Finished.

niloy2007 · 05-03-2017, 14:44

Operation : Format FS
Checking for existing devices... Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM4)
Driver Info : HS Corporation, ghsser.sys, 10.2104.1.2
Connecting to phone... OK
Waiting for response... OK
Init Handshake Sequence... OK
Hardware ID : E1507000 [8916] 00000000
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8916.ufl]... Done
Executing Loader... OK
Hardware : 8916, eMMC, 8 GB
Payload Info : In: 262144 [4096], Out: 16384, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device : Xiaomi 2014811 [msm8916]
Software : KTU84P, V6.3.5.0.KHJMIBL [Sat Mar 7 00:28:07 CST 2015]
Android Ver. : 4.4.4
Preparing Data... Done
Formatting Userdata... Done
Operation Finished.

niloy2007 · 05-04-2017, 12:54

Code:

Device: Samsung Device
Operation: Reset FRP (New Method)
Port: COM66 : SAMSUNG Mobile USB Modem #16
Checking for Device... Found [Normal Mode]
Reading Phone Information... OK
Model: SM-J210F
IMEI: 352801080683076
Software: J210FXXU0APK1/J210FODD0APK1/J210FXXU0APK1/J210FXXU0APK1
Init Download Mode... OK
Port: COM10 : SAMSUNG Mobile USB Modem
Reading Data from Phone... Done
Chipset: SPRD8735 [HiSpeed]
Resetting FRP Lock Data... . Done
Closing Session... Done
---------------- IMPORTANT ----------------
Wait for phone to reboot and turn on fully or TURN ON manually.
Once Phone is completely ON, wait a few minutes and then.
goto Menu > Settings > Backup and Reset and do Factory data Reset.
Elapsed Time: 01:02
[Ultimate Samsung Flasher v1.1]

.::THE ROCK::. · 05-04-2017, 14:18

Operation : Reset FRP
Checking for existing devices... Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Found Port : HS-USB Diagnostics 9008 (COM56)
Driver Info : Mobile, qcusbser.sys, 2.1.0.3
Connecting to phone... OK
Waiting for response... OK
Init Handshake Sequence... OK
Hardware ID : E1507000 [8916] [00000000]
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8916.ufl]... Done
Executing Loader... OK
Hardware : 8916, eMMC, 16 GB
Warning! High Speed Driver not installed.
Please install driver from QcFire\Drivers folder.
Payload Info : In: 65536 [4096], Out: 16384, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device : LYF LS-5005 [msm8916]
Software : TBT575522_1002_V020025, TBT575522_1002_V020025 [Fri Jan 6 16:30:34 CST 2017]
Android Ver. : 5.1.1
Resetting FRP Lock... . . Done
Operation Finished.

Tanha0321 · 05-04-2017, 14:56

Tanha0321 · 05-04-2017, 14:58

sevgiesenler · 05-04-2017, 15:55

bencharqui1 · 05-04-2017, 19:21

Operation : Read Firmware
Checking for existing devices... Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Found Port : Qualcomm HS-USB QDLoader (COM6)
Driver Info : Condor Communication Equipment Co.,Ltd., gnusbser.sys, 2.1.0.4
Connecting to phone... OK
Waiting for response... OK
Init Handshake Sequence... OK
Hardware ID : E1507000 [8916] 00000000
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8916.ufl]... Done
Executing Loader... OK
Hardware : 8916, eMMC, 16 GB
Warning! High Speed Driver not installed.
Please install driver from QcFire\Drivers folder.
Payload Info : In: 65536 [4096], Out: 16384, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device : OPPO A37f [msm8916]
Software : A37fEX_11_170302, 1480422943 [Thu Mar 2 08:44:55 CST 2017]
Android Ver. : 5.1.1
Reading [modem]... Done
Reading [sec]... Done
Reading [sbl1]... Done
Reading [sbl1bak]... Done
Reading [aboot]... Done
Reading [abootbak]... Done
Reading [rpm]... Done
Reading [rpmbak]... Done
Reading [tz]... Done
Reading [tzbak]... Done
Reading [hyp]... Done
Reading [hypbak]... Done
Reading [oppodycnvbk]... Done
Reading [oppostanvbk]... Done
Reading [LOGO]... Done
Reading [boot]... Done
Reading [recovery]... Done
Reading [system]... Done
Reading [cache]... Done
Reading [persist]... Done
Reading [misc]... Done
Reading [DRIVER]... Done
Reading [userdata]... Done
Reading [PrimaryGPT]... Done
Reading [BackupGPT]... Done
Saved to : C:\Users\tiktoshi2\Desktop\A37f_A37fEX_11_170302_5 .1.1\
Operation Finished.

narendrasingh · 05-05-2017, 05:18

mi 3s successfully format reset

Operation : Format FS
Checking for existing devices... Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM99)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2
Connecting to phone... OK
Waiting for response... OK
Init Handshake Sequence... OK
Hardware ID : E1F00400 [8937] 00000000
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8937.ufl]... Done
Executing Loader... OK
Hardware : 8937, eMMC, 32 GB
Warning! High Speed Driver not installed.
Please install driver from QcFire\Drivers folder.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device : Xiaomi Redmi 3S [msm8937]
Software : MMB29M, V8.1.1.0.MALMIDI [Tue Nov 8 11:47:48 CST 2016]
Android Ver. : 6.0.1
Preparing Data... Done
Formatting Userdata... Done
Operation Finished.

REGDS

Narendra Singh

.::THE ROCK::. · 05-05-2017, 08:33

Device: Samsung Device
Operation: Reset FRP (New Method)
Port: COM65 : SAMSUNG Mobile USB Modem #12
Checking for Device... Found [Normal Mode]
Reading Phone Information... OK
Model: SM-J200G
IMEI: 35714908++++++++
Software: J200GDCU2APL6/J200GODD2APL6/J200GDDU2APJ2/J200GDCU2APL6
Init Download Mode... OK
Port: COM10 : SAMSUNG Mobile USB Modem #2
Reading Data from Phone... Done
Chipset: LSI3475 [HiSpeed]
Resetting FRP Lock Data... . Done
Closing Session... Done
---------------- IMPORTANT ----------------
Wait for phone to reboot and turn on fully or TURN ON manually.
Once Phone is completely ON, wait a few minutes and then.
goto Menu > Settings > Backup and Reset and do Factory data Reset.
Elapsed Time: 01:13
[Ultimate Samsung Flasher v1.1]

bencharqui1 · 05-05-2017, 10:38

Port : COM27 : LGE Mobile USB Serial Port (COM27)
Baud Rate : 115200 (Auto)
Device : LG Android
Operation : FRP Reset (Universal)
Opening Port... OK
Reading Phone Information... OK
Model : LG-K350Z
SW Ver. : LGK350ZAT-00-V10a-AME-XX-MAR-23-2016+0
And. Ver. : 6.0
IMEI : 300000000000000
Prd. ID : VS06S160511001233
HW Ver. : rev_10
LAF Ver. : 1.1
Reading Partition Data... OK
Erasing FRP Lock... Done
Operation Finished.
Elapsed Time: 00:04
[Module Ver. 3.8]
Log Saved to Logs\170505_103406.log

niloy2007 · 05-05-2017, 13:41

Code:

Operation    : Reset Mi Account
Checking for existing devices... Found
Port    : COM4
Opening Port... OK
Init Handshake Sequence... OK
Hardware ID    : E1600400 [8953] 00000000
Initializing Protocol... OK
Using Auto Selection
Preparing Firehose Loader... Done
Sending Loader [8953.ufl]... Done
Executing Loader... OK
Hardware    : 8953, eMMC, 64 GB
Payload Info    : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device    : Xiaomi Redmi Note 4 [msm8953]
Software    : MMB29M, V8.2.4.0.MCFMIDL [Fri Apr  7 09:18:33 WIB 2017]
Android Ver.    : 6.0.1
Reading Data... Done
Resetting Mi Account... Done
Operation Finished.

Code:

Operation    : Read Firmware
Checking for existing devices... Found
Port    : COM4
Opening Port... OK
Init Handshake Sequence... OK
Hardware ID    : E1600400 [8953] 00000000
Initializing Protocol... OK
Using Auto Selection
Preparing Firehose Loader... Done
Sending Loader [8953.ufl]... Done
Executing Loader... OK
Hardware    : 8953, eMMC, 64 GB
Payload Info    : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device    : Xiaomi Redmi Note 4 [msm8953]
Software    : MMB29M, V8.2.4.0.MCFMIDL [Fri Apr  7 09:18:33 WIB 2017]
Android Ver.    : 6.0.1
Reading [modem]... Done
Reading [sbl1]... Done
Reading [sbl1bak]... Done
Reading [rpm]... Done
Reading [rpmbak]... Done
Reading [tz]... Done
Reading [tzbak]... Done
Reading [devcfg]... Done
Reading [devcfgbak]... Done
Reading [dsp]... Done
Reading [sec]... Done
Reading [splash]... Done
Reading [aboot]... Done
Reading [abootbak]... Done
Reading [boot]... Done
Reading [recovery]... Done
Reading [system]... Done
Reading [cache]... Done
Reading [persist]... Done
Reading [misc]... Done
Reading [mdtp]... Done
Reading [lksecapp]... Done
Reading [lksecappbak]... Done
Reading [cmnlib]... Done
Reading [cmnlibbak]... Done
Reading [cmnlib64]... Done
Reading [cmnlib64bak]... Done
Reading [keymaster]... Done
Reading [keymasterbak]... Done
Reading [cust]... Done
Reading [userdata]...

.::THE ROCK::. · 05-05-2017, 16:46

Device: Samsung Device
Operation: Reset FRP (New Method)
Port: COM70 : SAMSUNG Mobile USB Modem #14
Checking for Device... Found [Normal Mode]
Reading Phone Information... OK
Model: SM-J210F
IMEI: 352801088+++++++
Software: J210FXXU0APK4/J210FODD0APK4/J210FXXU0AQB2/J210FXXU0APK4
Init Download Mode... OK
Port: COM10 : SAMSUNG Mobile USB Modem #2
Reading Data from Phone... Done
Chipset: SPRD8735 [HiSpeed]
Resetting FRP Lock Data... . Done
Closing Session... Done
---------------- IMPORTANT ----------------
Wait for phone to reboot and turn on fully or TURN ON manually.
Once Phone is completely ON, wait a few minutes and then.
goto Menu > Settings > Backup and Reset and do Factory data Reset.
Elapsed Time: 00:58
[Ultimate Samsung Flasher v1.1]

05-03-2017, 14:44	#2569 (permalink)
niloy2007 No Life Poster Join Date: Oct 2010 Location: INDIA (WEST BENGAL) Posts: 1,288 Member: 1426012 Status: Offline Sonork: ICQ#618627674 Thanks Meter: 886	Operation : Format FS Checking for existing devices... Not Found Turn Off phone, hold Operation : Format FS Checking for existing devices... Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Found Port : Qualcomm HS-USB QDLoader 9008 (COM4) Driver Info : HS Corporation, ghsser.sys, 10.2104.1.2 Connecting to phone... OK Waiting for response... OK Init Handshake Sequence... OK Hardware ID : E1507000 [8916] 00000000 Initializing Protocol... OK Preparing Firehose Loader... Done Sending Loader [8916.ufl]... Done Executing Loader... OK Hardware : 8916, eMMC, 8 GB Payload Info : In: 262144 [4096], Out: 16384, Sector Size: 512 Reading Partition Table... OK Reading Device Information... OK Device : Xiaomi 2014811 [msm8916] Software : KTU84P, V6.3.5.0.KHJMIBL [Sat Mar 7 00:28:07 CST 2015] Android Ver. : 4.4.4 Preparing Data... Done Formatting Userdata... Done Operation Finished.

05-04-2017, 14:18	#2571 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	LYF LS-5005 frp done Operation : Reset FRP Checking for existing devices... Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Found Port : HS-USB Diagnostics 9008 (COM56) Driver Info : Mobile, qcusbser.sys, 2.1.0.3 Connecting to phone... OK Waiting for response... OK Init Handshake Sequence... OK Hardware ID : E1507000 [8916] [00000000] Initializing Protocol... OK Preparing Firehose Loader... Done Sending Loader [8916.ufl]... Done Executing Loader... OK Hardware : 8916, eMMC, 16 GB Warning! High Speed Driver not installed. Please install driver from QcFire\Drivers folder. Payload Info : In: 65536 [4096], Out: 16384, Sector Size: 512 Reading Partition Table... OK Reading Device Information... OK Device : LYF LS-5005 [msm8916] Software : TBT575522_1002_V020025, TBT575522_1002_V020025 [Fri Jan 6 16:30:34 CST 2017] Android Ver. : 5.1.1 Resetting FRP Lock... . . Done Operation Finished.

05-04-2017, 14:56	#2572 (permalink)
Tanha0321 No Life Poster Join Date: Jul 2006 Location: Pakistan karachi Posts: 9,760 Member: 314003 Status: Offline Thanks Meter: 2,999	Motorola Xt1254 Frp Reset

05-04-2017, 14:58	#2573 (permalink)
Tanha0321 No Life Poster Join Date: Jul 2006 Location: Pakistan karachi Posts: 9,760 Member: 314003 Status: Offline Thanks Meter: 2,999	HTC Desire 626s Frp Reset

05-05-2017, 08:33	#2577 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	SAMSUNG SM-J200G Reset FRP (New Method) Device: Samsung Device Operation: Reset FRP (New Method) Port: COM65 : SAMSUNG Mobile USB Modem #12 Checking for Device... Found [Normal Mode] Reading Phone Information... OK Model: SM-J200G IMEI: 35714908++++++++ Software: J200GDCU2APL6/J200GODD2APL6/J200GDDU2APJ2/J200GDCU2APL6 Init Download Mode... OK Port: COM10 : SAMSUNG Mobile USB Modem #2 Reading Data from Phone... Done Chipset: LSI3475 [HiSpeed] Resetting FRP Lock Data... . Done Closing Session... Done ---------------- IMPORTANT ---------------- Wait for phone to reboot and turn on fully or TURN ON manually. Once Phone is completely ON, wait a few minutes and then. goto Menu > Settings > Backup and Reset and do Factory data Reset. Elapsed Time: 01:13 [Ultimate Samsung Flasher v1.1]

05-04-2017, 15:55	#2574 (permalink)
sevgiesenler No Life Poster Join Date: Mar 2004 Location: esenler sevgiiletişim TR Age: 58 Posts: 589 Member: 60560 Status: Offline Sonork: 100.89085 Thanks Meter: 134

05-04-2017, 19:21	#2575 (permalink)
bencharqui1 No Life Poster Join Date: Aug 2011 Location: Algeria is a North African Age: 35 Posts: 1,879 Member: 1629321 Status: Offline Thanks Meter: 823	Operation : Read Firmware Checking for existing devices... Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Found Port : Qualcomm HS-USB QDLoader (COM6) Driver Info : Condor Communication Equipment Co.,Ltd., gnusbser.sys, 2.1.0.4 Connecting to phone... OK Waiting for response... OK Init Handshake Sequence... OK Hardware ID : E1507000 [8916] 00000000 Initializing Protocol... OK Preparing Firehose Loader... Done Sending Loader [8916.ufl]... Done Executing Loader... OK Hardware : 8916, eMMC, 16 GB Warning! High Speed Driver not installed. Please install driver from QcFire\Drivers folder. Payload Info : In: 65536 [4096], Out: 16384, Sector Size: 512 Reading Partition Table... OK Reading Device Information... OK Device : OPPO A37f [msm8916] Software : A37fEX_11_170302, 1480422943 [Thu Mar 2 08:44:55 CST 2017] Android Ver. : 5.1.1 Reading [modem]... Done Reading [sec]... Done Reading [sbl1]... Done Reading [sbl1bak]... Done Reading [aboot]... Done Reading [abootbak]... Done Reading [rpm]... Done Reading [rpmbak]... Done Reading [tz]... Done Reading [tzbak]... Done Reading [hyp]... Done Reading [hypbak]... Done Reading [oppodycnvbk]... Done Reading [oppostanvbk]... Done Reading [LOGO]... Done Reading [boot]... Done Reading [recovery]... Done Reading [system]... Done Reading [cache]... Done Reading [persist]... Done Reading [misc]... Done Reading [DRIVER]... Done Reading [userdata]... Done Reading [PrimaryGPT]... Done Reading [BackupGPT]... Done Saved to : C:\Users\tiktoshi2\Desktop\A37f_A37fEX_11_170302_5 .1.1\ Operation Finished.

05-05-2017, 05:18	#2576 (permalink)
narendrasingh No Life Poster Join Date: Apr 2009 Location: The Great India Posts: 711 Member: 1004995 Status: Offline Thanks Meter: 230	mi 3s successfully format reset Operation : Format FS Checking for existing devices... Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Found Port : Qualcomm HS-USB QDLoader 9008 (COM99) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.2 Connecting to phone... OK Waiting for response... OK Init Handshake Sequence... OK Hardware ID : E1F00400 [8937] 00000000 Initializing Protocol... OK Preparing Firehose Loader... Done Sending Loader [8937.ufl]... Done Executing Loader... OK Hardware : 8937, eMMC, 32 GB Warning! High Speed Driver not installed. Please install driver from QcFire\Drivers folder. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table... OK Reading Device Information... OK Device : Xiaomi Redmi 3S [msm8937] Software : MMB29M, V8.1.1.0.MALMIDI [Tue Nov 8 11:47:48 CST 2016] Android Ver. : 6.0.1 Preparing Data... Done Formatting Userdata... Done Operation Finished. REGDS Narendra Singh

05-05-2017, 10:38	#2578 (permalink)
bencharqui1 No Life Poster Join Date: Aug 2011 Location: Algeria is a North African Age: 35 Posts: 1,879 Member: 1629321 Status: Offline Thanks Meter: 823	Port : COM27 : LGE Mobile USB Serial Port (COM27) Baud Rate : 115200 (Auto) Device : LG Android Operation : FRP Reset (Universal) Opening Port... OK Reading Phone Information... OK Model : LG-K350Z SW Ver. : LGK350ZAT-00-V10a-AME-XX-MAR-23-2016+0 And. Ver. : 6.0 IMEI : 300000000000000 Prd. ID : VS06S160511001233 HW Ver. : rev_10 LAF Ver. : 1.1 Reading Partition Data... OK Erasing FRP Lock... Done Operation Finished. Elapsed Time: 00:04 [Module Ver. 3.8] Log Saved to Logs\170505_103406.log

05-05-2017, 16:46	#2580 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	SAMSUNG SM-J210F Reset FRP (New Method) UMT Device: Samsung Device Operation: Reset FRP (New Method) Port: COM70 : SAMSUNG Mobile USB Modem #14 Checking for Device... Found [Normal Mode] Reading Phone Information... OK Model: SM-J210F IMEI: 352801088+++++++ Software: J210FXXU0APK4/J210FODD0APK4/J210FXXU0AQB2/J210FXXU0APK4 Init Download Mode... OK Port: COM10 : SAMSUNG Mobile USB Modem #2 Reading Data from Phone... Done Chipset: SPRD8735 [HiSpeed] Resetting FRP Lock Data... . Done Closing Session... Done ---------------- IMPORTANT ---------------- Wait for phone to reboot and turn on fully or TURN ON manually. Once Phone is completely ON, wait a few minutes and then. goto Menu > Settings > Backup and Reset and do Factory data Reset. Elapsed Time: 00:58 [Ultimate Samsung Flasher v1.1]