★★★ Post Here All Successfully Repaired Phones by Ultimate Multi Tool ★★★ - Page 170 - GSM-Forum

.::THE ROCK::. · 04-28-2017, 17:48

Device: Samsung Device
Operation: Reset FRP (New Method)
Port: COM94 : SAMSUNG Mobile USB Modem #24
Checking for Device... Found [Normal Mode]
Reading Phone Information... OK
Model: SM-J500F
IMEI: 35267207+++++++++=
Software: J500FXXU1BQB2/J500FODD1BQA1/J500FDDU1BPK2/J500FXXU1BQB2
Init Download Mode... OK
Port: COM4 : SAMSUNG Mobile USB Modem #3
Reading Data from Phone... Done
Chipset: MSM8916 [HiSpeed]
Resetting FRP Lock Data... . Done
Closing Session... Done
---------------- IMPORTANT ----------------
Wait for phone to reboot and turn on fully or TURN ON manually.
Once Phone is completely ON, wait a few minutes and then.
goto Menu > Settings > Backup and Reset and do Factory data Reset.
Elapsed Time: 01:05
[Ultimate Samsung Flasher v1.1]

niloy2007 · 04-29-2017, 07:26

Code:

Operation    : Reset FRP
Checking for existing devices... Found
Port    : COM4
Opening Port... OK
Init Handshake Sequence... OK
Hardware ID    : E1009600 [8909] [00000000]
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8909.ufl]... Done
Executing Loader... OK
Hardware    : 8909, eMMC, 8 GB
Payload Info    : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device    : LYF LS-4503 [msm8909]
Software    : LS-4503-S10A_LYF_L11EN_210_160115, fd9d8f9 [Mon Feb 20 10:03:20 CST 2017]
Android Ver.    : 5.1.1
Resetting FRP Lock... . . Done
Operation Finished.

niloy2007 · 04-29-2017, 09:07

Code:

Operation    : Read Firmware
Checking for existing devices... Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Found Port    : Qualcomm HS-USB QDLoader 9008 (COM4)
Driver Info    : HS Corporation, ghsser.sys, 10.2104.1.2
Connecting to phone... OK
Waiting for response... OK
Init Handshake Sequence... OK
Hardware ID    : E1B00600 [8940] [00000000]
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8940.ufl]... Done
Executing Loader... OK
Hardware    : 8937, eMMC, 32 GB
Payload Info    : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device    : OPPO CPH1701 [msm8937]
Software    : CPH1701EX_11_A.11_170421, eng.root.20170421.072824 [Fri Apr 21 07:31:14 CST 2017]
Android Ver.    : 6.0.1
Reading [modem]... Done
Reading [sbl1]... Done
Reading [sbl1bak]... Done
Reading [rpm]... Done
Reading [rpmbak]... Done
Reading [tz]... Done
Reading [tzbak]... Done
Reading [devcfg]... Done
Reading [devcfgbak]... Done
Reading [dsp]... Done
Reading [oppodycnvbk]... Done
Reading [oppostanvbk]... Done
Reading [LOGO]... Done
Reading [sec]... Done
Reading [splash]... Done
Reading [aboot]... Done
Reading [abootbak]... Done
Reading [boot]... Done
Reading [recovery]... Done
Reading [cache]... Done
Reading [system]... Done
Reading [persist]... Done
Reading [misc]... Done
Reading [mdtp]... Done
Reading [cmnlib]... Done
Reading [cmnlibbak]... Done
Reading [cmnlib64]... Done
Reading [cmnlib64bak]... Done
Reading [keymaster]... Done
Reading [keymasterbak]... Done
Reading [DRIVER]... Done
Reading [userdata]... Done
Reading [PrimaryGPT]... Done
Reading [BackupGPT]... Done
Operation Finished.

.::THE ROCK::. · 04-29-2017, 09:09

Operation : Format FS
Checking for existing devices... Found
Port : COM21
Opening Port... OK
Init Handshake Sequence... OK
Hardware ID : E1009B00 [8976] [00000000]
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8976.ufl]... Done
Executing Loader... OK
Hardware : 8976, eMMC, 16 GB
Warning! High Speed Driver not installed.
Please install driver from QcFire\Drivers folder.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device : Xiaomi Redmi Note 3 [msm8952]
Software : LMY47V, V8.0.6.0.LHOMIDG [Tue Oct 25 19:12:10 CST 2016]
Android Ver. : 5.1.1
Preparing Data... Done
Formatting Userdata... Done
Operation Finished.

niloy2007 · 04-29-2017, 13:14

Code:

Device: Samsung Device
Operation: Reset FRP (New Method)
Port: COM54 : SAMSUNG Mobile USB Modem #12
Checking for Device... Found [Normal Mode]
Reading Phone Information... OK
Model: SM-J200G
IMEI: 359268070824206
Software: J200GDDU2APL7/J200GODD2APL7/J200GDDU2APJ2/J200GDDU2APL7
Init Download Mode... OK
Port: COM10 : SAMSUNG Mobile USB Modem
Reading Data from Phone... Done
Chipset: LSI3475 [HiSpeed]
Resetting FRP Lock Data... . Done
Closing Session... Done
---------------- IMPORTANT ----------------
Wait for phone to reboot and turn on fully or TURN ON manually.
Once Phone is completely ON, wait a few minutes and then.
goto Menu > Settings > Backup and Reset and do Factory data Reset.
Elapsed Time: 01:18
[Ultimate Samsung Flasher v1.1]

.::THE ROCK::. · 04-29-2017, 14:12

Operation : Reset FRP
Checking for existing devices... Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Found Port : HS-USB Diagnostics 9008 (COM21)
Driver Info : Mobile, qcusbser.sys, 2.1.0.3
Connecting to phone... OK
Waiting for response... OK
Init Handshake Sequence... OK
Hardware ID : E1009600 [8909] [00000000]
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8909.ufl]... Done
Executing Loader... OK
Hardware : 8909, eMMC, Unknown
Warning! High Speed Driver not installed.
Please install driver from QcFire\Drivers folder.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device : LYF LS-4505 [msm8909]
Software : LS-4505-S16A_LYF_L11EN_201_160228, 83a28cb [Wed Feb 15 11:06:00 CST 2017]
Android Ver. : 5.1.1
Resetting FRP Lock... . . Done
Operation Finished.

.::THE ROCK::. · 04-30-2017, 08:13

Operation : Reset Mi Account
Checking for existing devices... Found
Port : COM21
Opening Port... OK
Init Handshake Sequence... OK
Hardware ID : E1009B00 [8976] [00000000]
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8976.ufl]... Done
Executing Loader... OK
Hardware : 8976, eMMC, 32 GB
Warning! High Speed Driver not installed.
Please install driver from QcFire\Drivers folder.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device : Xiaomi Redmi Note 3 [msm8952]
Software : MMB29M, V8.2.2.0.MHOMIDL [Fri Mar 24 15:36:11 CST 2017]
Android Ver. : 6.0.1
Reading Data... Done
Resetting Mi Account... Done
Operation Finished.

.::THE ROCK::. · 04-30-2017, 13:21

Searching for phone in sideload mode... Found
Device Id : land_global
Version : V8.1.1.0.MALMIDI
Code Base : 6.0.1
Ext Info : GB, en, F
Formatting Data... Done
Operation Finished.

rehmani · 04-30-2017, 14:31

lenovo zuk z1 frp remove done

Code:

Port    : Fastboot Interface
Baud Rate    : Not Applicable
Device    : Generic
Operation    : Qualcomm FRP Reset
Searching for Device in FastBoot Mode... OK
Reading Information... OK
FastBoot Ver.    : 0.5
Product    : MSM8974
Warranty    : Yes
Bootloader    : Locked
Bootloader is Locked. FRP Reset may fail!
Removing FRP Lock... Done
Operation Finished.
Elapsed Time: 00:07
[Module Ver. 3.8]
Log Saved to Logs\170427_160130.log

rehmani · 04-30-2017, 14:33

mts m151 repair security done

Code:

Port    : COM109 : Qualcomm HS-USB Diagnostics 9004 (COM109)
Baud Rate    : 921600
Device    : Lava M141
Operation    : Read Info
Opening Port... OK
Reading Information... OK
Compile    : Jan 15 2015 21:01:24
Release    : Apr 24 2010 23:00:00
Hw Ver.    : W027_KK9
ESN    : 00000000
MEID    : 00000000000000
IMEI    : 000000000000000
BUILD    : Q1110-W027_KK9A_M151_MTS-3375
Reading Extended Information... OK
User Code    : 0000
SPC    : 000000
Port Closed.
Operation Finished.
Time Taken: 00:01
Module Ver. [1.5]
Log Saved to Logs\170427_152610.log

Port    : COM109 : Qualcomm HS-USB Diagnostics 9004 (COM109)
Baud Rate    : 921600
Device    : Lava M141
Operation    : MEID Repair
Opening Port... OK
Reading Information... OK
Compile    : Jan 15 2015 21:01:24
Release    : Apr 24 2010 23:00:00
Hw Ver.    : W027_KK9
ESN    : 00000000
MEID    : 00000000000000
IMEI    : 000000000000000
BUILD    : Q1110-W027_KK9A_M151_MTS-3375
Reading Extended Information... OK
User Code    : 0000
SPC    : 000000
Writing MEID A100004C961---... OK
New MEID    : A100004C961---
Port Closed.
Operation Finished.
Time Taken: 00:01
Module Ver. [1.5]
Log Saved to Logs\170427_152614.log


Port    : COM109 : Qualcomm HS-USB Diagnostics 9004 (COM109)
Baud Rate    : 921600
Device    : Lava M141
Operation    : Read Info
Opening Port... OK
Reading Information... OK
Compile    : Jan 15 2015 21:01:24
Release    : Apr 24 2010 23:00:00
Hw Ver.    : W027_KK9
ESN    : 809233--
MEID    : A100004C961---
IMEI    : 000000000000000
BUILD    : Q1110-W027_KK9A_M151_MTS-3375
Reading Extended Information... OK
User Code    : 0000
SPC    : 000000
Port Closed.
Operation Finished.
Time Taken: 00:01
Module Ver. [1.5]
Log Saved to Logs\170427_152629.log

rehmani · 04-30-2017, 14:34

lyf ls5009 read rom done

Code:

Operation    : Read Firmware
Checking for existing devices... Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Found Port    : Qualcomm HS-USB QDLoader 9008 (COM42)
Driver Info    : Qualcomm Incorporated, qcusbser.sys, 2.0.6.7
Connecting to phone... OK
Waiting for response... OK
Init Handshake Sequence... OK
Hardware ID    : E1009600 [8909] [00000000]
Initializing Protocol... OK
Preparing Firehose Loader... Done
Sending Loader [8909.ufl]... Done
Executing Loader... OK
Hardware    : 8909, eMMC, 8 GB
Warning! High Speed Driver not installed.
Please install driver from QcFire\Drivers folder.
Payload Info    : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table... OK
Reading Device Information... OK
Device    : LYF LS-5009 [msm8909]
Software    : LS-5009-S11A_LYF_L11EN_209_160115, 7d00459 [Fri Feb 17 11:58:08 CST 2017]
Android Ver.    : 5.1.1
Reading [modem]... Done
Reading [sbl1]... Done
Reading [sbl1bak]... Done
Reading [aboot]... Done
Reading [abootbak]... Done
Reading [rpm]... Done
Reading [rpmbak]... Done
Reading [tz]... Done
Reading [tzbak]... Done
Reading [misc]... Done
Reading [splash]... Done
Reading [sec]... Done
Reading [boot]... Done
Reading [system]... Done
Reading [persist]... Done
Reading [cache]... Done
Reading [recovery]... Done
Reading [userdata]... Done
Reading [PrimaryGPT]... Done
Reading [BackupGPT]... Done
Operation Finished.

rehmani · 04-30-2017, 14:42

j500f format done

Code:

Port    : COM95 : SAMSUNG Mobile USB Modem #11
Baud Rate    : 115200
Device    : Samsung G361H
Operation    : Format Phone (AT)
Opening Port... OK
Reading Information... OK
Model    : SM-J500F
IMEI    : 35959407351----
Version Info    : J500FXXU1APD6
    : J500FODD1APD6
    : J500FDDU1APE1
    : J500FXXU1APD6
Formatting Phone... OK
Phone Will Reboot When Done.
Port Closed.
Operation Finished.
Elapsed Time: 00:07
[Module Ver. 3.8]
Log Saved to Logs\170426_143451.log

rehmani · 04-30-2017, 14:48

olive c2130 unlock done

Code:

Port    : COM82 : Olive CDMA Device HS-USB Diagnostics (COM82)
Baud Rate    : 921600
Device    : Haier OL2130
Operation    : Unlock
Opening Port... OK
Reading Information... OK
Compile    : Oct 22 2013 14:51:43
Release    : Apr 14 2011 21:00:00
Hw Ver.    : 6012TT33
ESN    : 805300--
MEID    : A100002103E---
BUILD    : VC2130-3385
Setting Download Mode... OK
Reconnecting Phone... OK
Preparing Phone.. OK
Sending Bootloader... OK
Executing Bootloader... OK
Syncing Communication... OK
Initializing Flash Chip...
Flash Chip    : INTEL PF38F3050M0Y3DEA
Chip Size    : 16 MB
Preparing Patch Data... OK
Patching Firmware... OK
Resetting Phone... OK
Phone Successfully Unlocked.
Port Closed.
Operation Finished.
Time Taken: 00:21
Module Ver. [1.5]
Log Saved to Logs\170425_133016.log

.::THE ROCK::. · 05-01-2017, 07:15

Device: Samsung Device
Operation: Reset FRP (New Method)
Port: COM98 : SAMSUNG Mobile USB Modem #25
Checking for Device... Found [Normal Mode]
Reading Phone Information... OK
Model: SM-J210F
IMEI: 3541750+++++++++
Software: J210FXXU0AQD1/J210FODD0AQD1/J210FXXU0AQD1/J210FXXU0AQD1
Init Download Mode... OK
Port: COM4 : SAMSUNG Mobile USB Modem #3
Reading Data from Phone... Done
Chipset: SPRD8735 [HiSpeed]
Resetting FRP Lock Data... . Done
Closing Session... Done
---------------- IMPORTANT ----------------
Wait for phone to reboot and turn on fully or TURN ON manually.
Once Phone is completely ON, wait a few minutes and then.
goto Menu > Settings > Backup and Reset and do Factory data Reset.
Elapsed Time: 00:58
[Ultimate Samsung Flasher v1.1]

.::THE ROCK::. · 05-01-2017, 07:35

Port : Fastboot Interface
Baud Rate : Not Applicable
Device : Generic
Operation : Huawei SPD FRP Reset
Searching for Device in FastBoot Mode... OK
Reading Information... OK
FastBoot Ver. : 1.0
Product
Bootloader : Locked
Bootloader is Locked. FRP Reset may fail!
Removing FRP Lock... Done
Operation Finished.
Elapsed Time: 00:14
[Module Ver. 3.8]
Log Saved to Logs\170501_115204.log

04-28-2017, 17:48	#2536 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	SAMSUNG SM-J500F Reset FRP (New Method) U.M.T Device: Samsung Device Operation: Reset FRP (New Method) Port: COM94 : SAMSUNG Mobile USB Modem #24 Checking for Device... Found [Normal Mode] Reading Phone Information... OK Model: SM-J500F IMEI: 35267207+++++++++= Software: J500FXXU1BQB2/J500FODD1BQA1/J500FDDU1BPK2/J500FXXU1BQB2 Init Download Mode... OK Port: COM4 : SAMSUNG Mobile USB Modem #3 Reading Data from Phone... Done Chipset: MSM8916 [HiSpeed] Resetting FRP Lock Data... . Done Closing Session... Done ---------------- IMPORTANT ---------------- Wait for phone to reboot and turn on fully or TURN ON manually. Once Phone is completely ON, wait a few minutes and then. goto Menu > Settings > Backup and Reset and do Factory data Reset. Elapsed Time: 01:05 [Ultimate Samsung Flasher v1.1]

04-29-2017, 09:09	#2539 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	Xiaomi Redmi Note 3 FORMAT HANG LOGO SOLVED UMT Operation : Format FS Checking for existing devices... Found Port : COM21 Opening Port... OK Init Handshake Sequence... OK Hardware ID : E1009B00 [8976] [00000000] Initializing Protocol... OK Preparing Firehose Loader... Done Sending Loader [8976.ufl]... Done Executing Loader... OK Hardware : 8976, eMMC, 16 GB Warning! High Speed Driver not installed. Please install driver from QcFire\Drivers folder. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table... OK Reading Device Information... OK Device : Xiaomi Redmi Note 3 [msm8952] Software : LMY47V, V8.0.6.0.LHOMIDG [Tue Oct 25 19:12:10 CST 2016] Android Ver. : 5.1.1 Preparing Data... Done Formatting Userdata... Done Operation Finished.

04-29-2017, 14:12	#2541 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	Lyf ls-4505 frp done umt Operation : Reset FRP Checking for existing devices... Not Found Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable. Found Port : HS-USB Diagnostics 9008 (COM21) Driver Info : Mobile, qcusbser.sys, 2.1.0.3 Connecting to phone... OK Waiting for response... OK Init Handshake Sequence... OK Hardware ID : E1009600 [8909] [00000000] Initializing Protocol... OK Preparing Firehose Loader... Done Sending Loader [8909.ufl]... Done Executing Loader... OK Hardware : 8909, eMMC, Unknown Warning! High Speed Driver not installed. Please install driver from QcFire\Drivers folder. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table... OK Reading Device Information... OK Device : LYF LS-4505 [msm8909] Software : LS-4505-S16A_LYF_L11EN_201_160228, 83a28cb [Wed Feb 15 11:06:00 CST 2017] Android Ver. : 5.1.1 Resetting FRP Lock... . . Done Operation Finished.

04-30-2017, 08:13	#2542 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	Xiaomi Redmi Note 3 mi account remove done Operation : Reset Mi Account Checking for existing devices... Found Port : COM21 Opening Port... OK Init Handshake Sequence... OK Hardware ID : E1009B00 [8976] [00000000] Initializing Protocol... OK Preparing Firehose Loader... Done Sending Loader [8976.ufl]... Done Executing Loader... OK Hardware : 8976, eMMC, 32 GB Warning! High Speed Driver not installed. Please install driver from QcFire\Drivers folder. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table... OK Reading Device Information... OK Device : Xiaomi Redmi Note 3 [msm8952] Software : MMB29M, V8.2.2.0.MHOMIDL [Fri Mar 24 15:36:11 CST 2017] Android Ver. : 6.0.1 Reading Data... Done Resetting Mi Account... Done Operation Finished.

04-30-2017, 13:21	#2543 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	mi 3s format done umt Searching for phone in sideload mode... Found Device Id : land_global Version : V8.1.1.0.MALMIDI Code Base : 6.0.1 Ext Info : GB, en, F Formatting Data... Done Operation Finished.

05-01-2017, 07:15	#2549 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	SAMSUNG SM-J210F Reset FRP (New Method) UMT Device: Samsung Device Operation: Reset FRP (New Method) Port: COM98 : SAMSUNG Mobile USB Modem #25 Checking for Device... Found [Normal Mode] Reading Phone Information... OK Model: SM-J210F IMEI: 3541750+++++++++ Software: J210FXXU0AQD1/J210FODD0AQD1/J210FXXU0AQD1/J210FXXU0AQD1 Init Download Mode... OK Port: COM4 : SAMSUNG Mobile USB Modem #3 Reading Data from Phone... Done Chipset: SPRD8735 [HiSpeed] Resetting FRP Lock Data... . Done Closing Session... Done ---------------- IMPORTANT ---------------- Wait for phone to reboot and turn on fully or TURN ON manually. Once Phone is completely ON, wait a few minutes and then. goto Menu > Settings > Backup and Reset and do Factory data Reset. Elapsed Time: 00:58 [Ultimate Samsung Flasher v1.1]

05-01-2017, 07:35	#2550 (permalink)
.::THE ROCK::. Product Supporter Join Date: Jul 2011 Location: ISLAMIC & INDIA WITH MIRACLE T Age: 37 Posts: 5,807 Member: 1617868 Status: Offline Sonork: 100.1625996 Thanks Meter: 2,028	Xolo spd frp done Port : Fastboot Interface Baud Rate : Not Applicable Device : Generic Operation : Huawei SPD FRP Reset Searching for Device in FastBoot Mode... OK Reading Information... OK FastBoot Ver. : 1.0 Product Bootloader : Locked Bootloader is Locked. FRP Reset may fail! Removing FRP Lock... Done Operation Finished. Elapsed Time: 00:14 [Module Ver. 3.8] Log Saved to Logs\170501_115204.log