Successfully unlocked/repaired phones by Infinity-Box - Page 1577 - GSM-Forum

ij_cell · 07-13-2015, 18:06

Nokia e52-1 format and factory setting done.

Format File System...
Operating mode is OK, no need change...
Scanning FS parametres...
Checking Data...
Detected : 2 drive(s)...
Start formating....
Using Series 60 format algorithm...
==================================
Formating drive : C now...
Step1 : OK
Step2 : OK
End format...
==================================
Formating drive : D now...
Step1 : OK
Step2 : OK
End format...
==================================
Done!

Resetting selected items...
Check phone mode...
Phone in Local mode
Seting Test mode... wait...
Test mode set
Settings Full Factory Defaults...
Set OK!
Settings Software Upgrade Defaults...
Set OK!
Settings Service Centre Defaults...
Set OK!
Settings Production Tune Defaults...
Set OK!
Settings User Data Defaults...
Set OK!
Settings Leave Factory defaults...
Set OK!

Elapsed: 00:00:07

Reading Phone Info....
Connected phone - Nokia E52-1
Software ver : V ICPR82_09w36.5 09-10-09 RM-469 (c) Nokia
IMEI : 359327030373439
XappVer : 0000082A
Ape Ver : 022.009
APE Var : 022.009022.009.12.01022.009.209.03
APE ADSP: 256
DSP Ver : ICPR82_09w36.4_RIO
APE Test: 0.068
PPM :
CNT :
Product SN : MHH947210
Product code : 0588050
Base Prd.code: 0565921
Long Prod.SN : 0
Hardware info=======
HWID : 6010
Retu : 40
Tahvo : 00
Batery: 3580 mV
APE HW: 256
Lock info ===========
IMEI : 359327030373439
IMEI spNet : 3A 95 23 07 03 73 43 03
IMEI svNet : 33 95 23 07 03 73 43 23 F8

Conf key : 0000000000000000
Provider key : 2440700000000000
Country : Finland
Operator : NOKIA (Open)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

SDD key status : Damaged!!!!!
CMLA Key status : Not Present
SimLock status : Ok
Security status : Ok
PA_SimLock Version :
PA_SL3 phone , SP_CODE_LEN : 15

User code : Crypted
UserDataExLevel : Low [Gallery] , FullFlash method

Done!

srinibas · 07-14-2015, 05:30

Reading Flash Conent now ...

Brand : Panasonic
ProdName : P55
ProdModel : Panasonic P55
Device : P55
AndroidVer: 4.4.2
MTKxCPU : MT6589
MTKxPRJ : ALPS.KK1.MP5.V1.5

[Read Ok] : preloader_yulong89_wet_kk.bin
[Read Ok] : MBR
[Read Ok] : EBR1
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : EBR2
[Read Ok] : autobak.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6589 / V1.0.0 / yulong89_wet_kk / EMMC
FW Size : 940 MiB
Scatter saved to : C:\Documents and Settings\Administrator\Desktop\New Folder (2)\MT6589__Panasonic__Panasonic P55__P55__4.4.2__ALPS.KK1.MP5.V1.5\

All done!

Br - srinibas

srinibas · 07-14-2015, 05:41

Operation : Read PatternLock [ v1.23 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 36 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4B0001154D565835E975014243212BD0
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : BMVX5
[eMMC] : FLASH_CID : 1501004B3558564D420175E9D02B2143
[eMMC] : FLASH_LEN : 0x00000000E9000000
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading data ...
FS Size : 2511 MiB
Magic Ok
Mount point : /data

Get PatternLock ...
PatternLock Sequnce : 14569

Done!
Elapsed: 00:00:20
Reconnect Power/Cable!

syed tuqeer · 07-14-2015, 06:40

Code:

IDM initializing, wait...
Checking access to Products folder...
Folder for RM-1134 not exist. Attempt to create
Prepare done, collect info
[Query] : RM-1134_ROM_eMP_10.01.11 , 208.54 KB 
[Query] : RM-1134_VIVA_eMP_10.01.11 , 1.94 MB 
[Query] : RM-1134_LANG_PACK_ROM_IC_eMP_10.01.11_011 , 361.80 KB 
[Query] : RM-1134_CUSTPACK_ROM_IC_MEA_JO_eMP_10.01.11_011 , 63.96 KB 
[Query] : RM-1134_JUMP_TABLE_IC_MEA_JO_eMP_10.01.11_011 , 1.15 KB 
[Query] : RM-1134_LAGOS61D_BB_eMP_059X092_care_10.01.11_011.cfg , 3.72 KB 
[Query] : RM1134_059X092_10.01.11_010.vpl , 4.45 KB 
Files to download : 7
Total size to download : 2.56 MB
Downloading now, please, wait...
[Download] : RM-1134_ROM_eMP_10.01.11
[Download] : RM-1134_VIVA_eMP_10.01.11
[Download] : RM-1134_LANG_PACK_ROM_IC_eMP_10.01.11_011
[Download] : RM-1134_CUSTPACK_ROM_IC_MEA_JO_eMP_10.01.11_011
[Download] : RM-1134_JUMP_TABLE_IC_MEA_JO_eMP_10.01.11_011
[Download] : RM-1134_LAGOS61D_BB_eMP_059X092_care_10.01.11_011.cfg
[Download] : RM1134_059X092_10.01.11_010.vpl
Verify files now ..... 
[Verify Ok] : RM-1134_LAGOS61D_BB_eMP_059X092_care_10.01.11_011.cfg
[Verify Ok] : RM-1134_ROM_eMP_10.01.11
[Verify Ok] : RM-1134_LANG_PACK_ROM_IC_eMP_10.01.11_011
[Verify Ok] : RM-1134_CUSTPACK_ROM_IC_MEA_JO_eMP_10.01.11_011
[Verify Ok] : RM-1134_JUMP_TABLE_IC_MEA_JO_eMP_10.01.11_011
[Verify Ok] : RM-1134_VIVA_eMP_10.01.11
All done, all files were downloaded!

mbiborna · 07-14-2015, 06:51

Symphony W85

Code:

Operation : Read PatternLock [ v1.23 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 17 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 90014A4834473164048600A32E292179
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : d1G4
[eMMC] : FLASH_CID : 90014A4834473164048600A32E292179
[eMMC] : FLASH_LEN : 0x00000000E7000000
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading data ... 
FS Size : 1023 MiB
Magic Ok
Mount point  : /data

Get PatternLock ...
PatternLock Sequnce : 47589

Done!
Elapsed: 00:00:23
Reconnect Power/Cable!

PASSIONATE_BOYS · 07-14-2015, 07:18

Rage Optima Smart G40 read Pattern Lock, FF and NVRAM done-

Read Pattern Lock-

Code:

Operation : Read PatternLock [ v1.23 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 7001004D4D43303447580B33C317311B
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D43303447580B33C317311B
[eMMC] : FLASH_LEN : 0x00000000E6800000
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading data ... 
FS Size : 1323 MiB
Magic Ok
Mount point  : /data

Get PatternLock ...
PatternLock Sequnce : 125874

Done!
Elapsed: 00:00:20
Reconnect Power/Cable!

Read FF-

Code:

Operation : Read Flash [ v1.23 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 7001004D4D43303447580B33C317311B
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D43303447580B33C317311B
[eMMC] : FLASH_LEN : 0x00000000E6800000
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ... 

Brand     : 40G
ProdName  : 40G
ProdModel : 40G
Device    : 40G
AndroidVer: 4.2.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.JB3.MP.V1.15

[Read Ok] : preloader_fars72_wet_v115_jb3.bin
[Read Ok] : MBR
[Read Ok] : EBR1
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img
[Read Ok] : fat.img

[ScatCFG] : MT6572 / V1.1.1 / fars72_wet_v115_jb3 / EMMC
FW Size : 678 MiB
Scatter saved to : C:\InfinityBox\CM2MTK\Flash\MT6572__40G__40G__40G__4.2.2__ALPS.JB3.MP.V1.15\

All done!

Done!
Elapsed: 00:03:26
Reconnect Power/Cable!

Read NVRAM-

Code:

Operation : Read NVRAM [ v1.23 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 7001004D4D43303447580B33C317311B
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D43303447580B33C317311B
[eMMC] : FLASH_LEN : 0x00000000E6800000
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Read Ok, Rage Optime Smart-40G_-MT6572_eMMC.spnv saved

Done!
Elapsed: 00:02:17
Reconnect Power/Cable!

Br.

situ_saraf · 07-14-2015, 07:45

Code:

Operation : Check / Read Info [ v1.23 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 50 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 7001004D4D4330344758CCE0C89D51CD
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D4330344758CCE0C89D51CD
[eMMC] : FLASH_LEN : 0x00000000E6800000
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!

Brand     : Micromax
ProdName  : Micromax A089
ProdModel : Micromax A089
Device    : A089
AndroidVer: 4.2.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.JB3.MP.V1

Done!
Elapsed: 00:00:12
Reconnect Power/Cable!

Finish at : [14-07-2015 / ????????? 10:18:03]

Code:

Operation : Read Flash [ v1.23 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 50 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 7001004D4D4330344758CCE0C89D51CD
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D4330344758CCE0C89D51CD
[eMMC] : FLASH_LEN : 0x00000000E6800000
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ... 

Brand     : Micromax
ProdName  : Micromax A089
ProdModel : Micromax A089
Device    : A089
AndroidVer: 4.2.2
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.JB3.MP.V1

[Read Ok] : preloader_s308.bin
[Read Ok] : MBR
[Read Ok] : EBR1
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : EBR2
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img
[Read Ok] : bytcfg.img
[Read Ok] : fat.img

[ScatCFG] : MT6572 / V1.1.1 / s308 / EMMC
FW Size : 682 MiB
Scatter saved to : C:\Users\JeeT\Desktop\A089\MT6572__Micromax__Micromax A089__A089__4.2.2__ALPS.JB3.MP.V1\

All done!

Done!
Elapsed: 00:03:17
Reconnect Power/Cable!

Code:

Operation : Repair Security [ v1.23 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 50 ]
Sync...
Init Ok, waiting for phone ...
Reading initial info, wait... 
Phone Info : 
BB : MT6572, E01
HW : BESTONE72_WET_JB3_HSPA_HW
SW : MOLY.WR8.W1315.MD.WG.MP.V1.P14
MM : 2000.00.00
VR : 1.0
Security Info : 
IMEI [1] : Damaged!
IMEI [2] : Damaged or not exists
Read Ok!
Update IMEI[1] to : 911354603882092 done!
Update IMEI[2] to : 911354603388215 done!

Done!
Elapsed: 00:00:49
Reconnect Power/Cable!

Finish at : [14-07-2015 / ????????? 10:36:01]

Luckey1 · 07-14-2015, 08:20

Code:

Core : v2.09 , BB5XG FlashEngine : v9.9

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm561__09.98.mcusw
PPM : rm561__09.98.ppm_t
CNT : rm561__09.98.image_ctv_nz_gray
Flashing phone now...
[Gen] Rules accepted for : RAP3x Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Getting product info...
Dead Mode is Selected
Waiting for USB device...
--- Press phone's power button or insert cable & charger! ---
Connection opened successfully
Waiting for communication response.
ASIC ID:       000000010000022600010006030C192101033000
CPU ID :       RAP3Gv3 , Features : No any extended features
RAP_PUB:   29F00012B3D646504CE0D035FD60863E636F3BA1
CMT_ROOT:  9DDBFCFE6E73CED7D8C6268C8EB85723
PatchRAWLoader: Patched OK
Processing RAWLOADER...
Processing UPDAPP...
Processing PASUBTOC...
TIME : Boot time : 00:00:06
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
Waiting for response: 28
Waiting for response: 27
Waiting for response: 26
Waiting for response: 25
Waiting for response: 24
Waiting for response: 23
Waiting for response: 22
Waiting for response: 21
Waiting for response: 20
Waiting for response: 19
Waiting for response: 18
Waiting for response: 17
Waiting for response: 16
Waiting for response: 15
Waiting for response: 14
Waiting for response: 13
Waiting for response: 12
Waiting for response: 11
Waiting for response: 10
ADL -> [2nd] changing...
ADL Server confirm flashmode!
ADL : Check data
ADL : Data accepted
   ===Flashing [MCU]===
Erase : Processing rm561__09.98.mcusw
Found 6 areas to erase
Erasing area 0x00000000 - 0x000006BF, NOR, CMT
Result: 0000
Erasing area 0x000006C0 - 0x0001FFFF, NOR, CMT
Result: 0000
Erasing area 0x00040000 - 0x000BFFFF, NOR, CMT
Result: 0000
Erasing area 0x000C0000 - 0x0013FFFF, NOR, CMT
Result: 0000
Erasing area 0x00140000 - 0x0137FFFF, NOR, CMT
Result: 0000
Erasing area 0x01380000 - 0x0151FFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:01:57
Write : Processing rm561__09.98.mcusw
Total 1256 [1256/0/0] blocks to write, writing... 
CMT : Writing Hash CERT [NOLO]
CMT : Writing Hash CERT [KEYS]
CMT : Writing Hash CERT [PRIMAPP]
CMT : Writing Hash CERT [PASUBTOC]
CMT : Writing Hash CERT [PAPUBKEYS]
CMT : Writing Hash CERT [UPDAPP]
CMT : Writing Hash CERT [DSP0]
CMT : Writing Hash CERT [MCUSW]
TIME : Write time : 00:01:25
MCU Write done
   ===Flashing [PPM]===
Erase : Processing rm561__09.98.ppm_t
Found 1 areas to erase
Erasing area 0x01520000 - 0x01DBFFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:00:51
Write : Processing rm561__09.98.ppm_t
Total 353 [353/0/0] blocks to write, writing... 
TIME : Write time : 00:00:24
PPM Write done
   ===Flashing [CNT]===
Erase : Processing rm561__09.98.image_ctv_nz_gray
Found 2 areas to erase
Erasing area 0x01DC0000 - 0x0215FFFF, NOR, CMT
Result: 0000
Erasing area 0x02160000 - 0x03FBFFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:03:18
Checking content info...
Check Image : Content size is 128k, use direct write mode
Write : Processing rm561__09.98.image_ctv_nz_gray
Total 528 [528/0/0] blocks to write, writing... 
TIME : Write time : 00:00:38
CNT Write done
ADL : End flashing

Flashing done!
Total flash time : 00:08:35
Reboot phone now...

Reading Phone Info....
Connected phone -   Nokia 2700 classic
Software Info:     V 09.98 06-09-10 RM-561 (c) Nokia            
IMEI:  351532048899337
PPM version :   V 09.97 18-06-10 RM-561 (c) Nokia             MEN
Product code:  0579321
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Product code update...
Check and Upload User Certificates ...
Total - 0 certs
Uploading User Certificates...
Uploaded 26 certs!
Battery voltage is enough for start
AfterFlash operations done ;D
Done!

Elapsed: 00:11:58

maanarman · 07-14-2015, 09:28

Code:

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 13 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8C00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 110100303034473930109D4A2ECBB087
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0011 , OEM : 0100
[eMMC] : FLASH_INF : 09G40
[eMMC] : FLASH_CID : 110100303034473930109D4A2ECBB087
[eMMC] : FLASH_LEN : 0x00000000EC000000
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ... 

Read Ok , collect info
Brand     : QMobile
ProdName  : QMobile A63
ProdModel : QMobile A63
Device    : x3365
AndroidVer: 4.2.2
MTKxCPU   : MT6572
MTKxPRJ   : X3365_DX33651_QMOBILE-A63-HLCM_L200
Saved to : C:\Documents and Settings\maanarman\Desktop\A63 QMOBILE dump\MT6572__QMOBILE__QMobile_A63__x3365__X3365_DX33651_QMOBILE-A63-HLCM_L200__Android_4.2.2__20140624_092224.ispff

Done!
Elapsed: 00:17:47
Reconnect Power/Cable!

maanarman · 07-14-2015, 09:29

Code:

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 182 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6571
BB_CPU_HW : CA00
BB_CPU_SW : 8D00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6571_S00
Processing BROM stage
BLVersion : 0xFE
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending 
NAND_ID : 009800BC009000660076001600080000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x8B
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00A8
DRAM Init Ok , 0x10000000
DA Sent. Configure setting now ... 
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ... 
USBDL : Init HSUSB Ok!
NAND settings not exists, will check now ... 
Settings read Ok!
 - > Re-connect battery and start operation again!


Done!
Elapsed: 00:00:32
Reconnect Power/Cable!


Operation : Read Flash [ v1.21 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 182 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6571
BB_CPU_HW : CA00
BB_CPU_SW : 8D00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6571_S00
Processing BROM stage
BLVersion : 0xFE
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending 
NAND_ID : 009800BC009000660076001600080000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x8B
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00A8
DRAM Init Ok , 0x10000000
DA Sent. Configure setting now ... 
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0011 , [KINGSTON] KTN0403CS_TCR1
[NAND] : FLASH_DIE : 0098 00BC 0090 0066 0076 0016 0008
[NAND] : FLASH_LEN : 0x20000000
INT RAM    : 0x00020000
EXT RAM    : 0x10000000
BOOT TYPE  : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ... 
USBDL : Init HSUSB Ok!

Read Ok , collect info
MTKxCPU   : MT6571
MTKxPRJ   : v13_v1bom_hl_voice
Saved to : C:\Documents and Settings\maanarman\Desktop\VOICE V10i\MT6571__v13_v1bom_hl_voice.ispff

Done!
Elapsed: 00:04:41
Reconnect Power/Cable!

maanarman · 07-14-2015, 09:30

Code:

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 13 ]
Sync...
Inital regs read done
Boot Info : 
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending 
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 7001004D4D4330344702103AA51411F9
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ... 
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : G40CM
[eMMC] : FLASH_CID : 7001004D4D4330344702103AA51411F9
[eMMC] : FLASH_LEN : 0x00000000E2C00000
INT RAM    : 0x00020000
EXT RAM    : 0x20000000
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Conent now ... 

Brand     : samsung
ProdName  : SM-N9006
ProdModel : SM-N9006
Device    : SM-N9006
AndroidVer: 4.3
MTKxCPU   : MT6572
MTKxPRJ   : ALPS.JB3.MP.V1

[Read Ok] : preloader_mbk72_wet_jb3.bin
[Read Ok] : MBR
[Read Ok] : EBR1
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img
[Read Ok] : fat.img

[ScatCFG] : MT6572 / V1.1.1 / mbk72_wet_jb3 / EMMC
FW Size : 678 MiB
Scatter saved to : C:\Documents and Settings\maanarman\Desktop\SM-N9006 SAMSUNG\MT6572__samsung__SM-N9006__SM-N9006__4.3__ALPS.JB3.MP.V1\

All done!

Done!
Elapsed: 00:09:44
Reconnect Power/Cable!

kariakala · 07-14-2015, 09:34

Code:

Chinese Miracle II  [SPD module] v 1.02

Loading    : SC7731_V120_KEW_281_V1.6_150427.pac
CRVersion  : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : SC7731_V120_KEW_281_V1.6_150427
FastCheck  : 0x37389C15

Loading files ... 

File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : SC7702_sc7731g_band128.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : logo.bmp
File : logo.bmp
File : cache.img
File : u-boot.bin
File : SC77xx.xml

Load Ok!

Operation : Flash [ v1.02 ]

======= Flash
Files set for flashing : 
[ MCU ] : SC7731_V120_KEW_281_V1.6_150427.pac
CRVersion  : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : SC7731_V120_KEW_281_V1.6_150427
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : SC7702_sc7731g_band128.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : logo.bmp
File : logo.bmp
File : cache.img
File : u-boot.bin

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

 ====  Wait for phone...

Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
PMTManager : Load 0x18 records
PMTManager : PMT Update Ok!
Flashing now

[FlashProc] : CODE  
Current ID : PRODNV
Current File : prodnv.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : SPLLOADER
Current File : u-boot-spl-16k.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_W
Current File : SC7702_sc7731g_band128.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : DSP_W
Current File : DSP_DM_G2.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : MODEM_WCN
Current File : SC8800G_x30g_wcn_dts_modem.bin
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOT
Current File : boot.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : RECOVERY
Current File : recovery.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : USERDATA
Current File : userdata.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : BOOTLOGO
Current File : logo.bmp
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : CODE  
Current ID : FASTBOOT_LOGO
Current File : logo.bmp
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH
Current Part : wruntimenv1
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : FLASH_WCN
Current Part : wcnruntimenv1
[FlashProc] : Ok!

[FlashProc] : IMAGE
Current ID : CACHE
Current File : cache.img
Flashing now ... 
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASEMISC
Current Part : misc
[FlashProc] : Ok!

[FlashProc] : ERASE 
Current ID   : ERASESD
Current Part : internalsd
[FlashProc] : Ok!

[FlashProc] : BOOTCODE
Current ID   : UBOOTLOADER
Current File : u-boot.bin
Flashing now ... 
[FlashProc] : Ok!


Elapsed: 00:06:31

Reconnect Power/Cable!

maanarman · 07-14-2015, 09:38

Code:

Verify files ... 
MAUI : RM-969_ROM_eMP_10.03.11
VIVA : RM-969_VIVA_eMP_10.03.11
LANG : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
CUST : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
JMPT : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
 - > MODE : FullFlash

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 36 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info : 
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : D20AA43BFFD2E946B1AA347938B7CE69
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Rivendell.10.03.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Rivendell.fg
DA_VERIFY : 00
DA_JUMP   : 00040000
DA_INFO   : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F8 , [WINBOND] W25Q128FW
[0] : FLASH_DIE : 00EF 0060 0018 0000 
[0] : FLASH_LEN : 0x01000000
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000
SecureDecrypt : RM-969_ROM_eMP_10.03.11
SecureDecrypt : RM-969_VIVA_eMP_10.03.11
SecureDecrypt : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
SecureDecrypt : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
SecureDecrypt : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
OVRLP : 000069B900000001
PHPID : Rivendell.10.03.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
ERASE_MAUI_INFO : 0x00040000
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-969_ROM_eMP_10.03.11
Write : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
Write : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
Write : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
Write : RM-969_VIVA_eMP_10.03.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-969_ROM_eMP_10.03.11
[VERIFY] DONE : RM-969_LANG_PACK_ROM_IJ_eMP_10.03.11
[VERIFY] DONE : RM-969_CUSTPACK_ROM_IJ_MEA_IR_eMP_10.03.11
[VERIFY] DONE : RM-969_JUMP_TABLE_IJ_MEA_IR_eMP_10.03.11
[VERIFY] DONE : RM-969_VIVA_eMP_10.03.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x00A60000-0x00FF3FFF , LEN : 0x00594000
DA_RET   : DA_IN_PROGRESS
DA_RET   : FORMAT_DONE
Rebooting phone now

Flashing done!
Total flash time : 00:03:10
Reboot phone Ok

Connect phone on selected interface...

maanarman · 07-14-2015, 09:38

Code:

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm827__03.04.mcusw
PPM : rm827__03.04.ppm_m4
CNT : rm827__03.04.image_m4_059N407
Flashing phone now...
[Gen] Rules accepted for : XGOLD Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len  : 0x0A
IF xCPUID    : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data  :  1FB300020303010100FF

Sending EBL Loader ... 
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ... 
EBL sent Ok
EBL : Quantum_Bootloader_10.49_M1S1
Speed accepted, use 6.500.000
FLASHID : 89008289
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Backup enabled, will read all certificates

Reading CCC
Reading HWC
Reading NPC

IMEI 1 : 353656052976588
IMEI 2 : 353656052976596
PCcode : 059N403

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : C:\InfinityBox\BEST\Backup\Cert\353656052976588_XG213_CRT.rpl

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

   ===Flashing [MCU]===
File : rm827__03.04.mcusw
Image : rm827__03.04.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ... 
Erase done, time : 00:00:00 
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ... 
Erase done, time : 00:00:00 
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ... 
Erase done, time : 00:00:05 
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:01
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01940000
Erasing, wait ... 
Erase done, time : 00:02:18 
Write , Start : 0x40280000 , Len : 0x018C0000
Flashing , wait ...
Region flash done, time : 00:00:47
Processing Region 5/5
Erase , Start : 0x43E20000 , Len : 0x00040000
Erasing, wait ... 
Erase done, time : 00:00:00 
No write data, skip
CRC check passed , 0x74A0

   ===Flashing [PPM]===
File : rm827__03.04.ppm_m4
Image : package_m4.ppm_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x41BC0000 , Len : 0x00600000
Erasing, wait ... 
Erase done, time : 00:00:17 
Write , Start : 0x41BC0000 , Len : 0x00380998
Flashing , wait ...
Region flash done, time : 00:00:04
CRC check passed , 0xA432

   ===Flashing [CNT]===
File : rm827__03.04.image_m4_059N407
Image : package_m4_059N407.image.fls
Sec-pack found, sending ...
Sec-pack sent
Found 2 region(s)
Processing Region 1/2
Erase , Start : 0x421C0000 , Len : 0x01C60000
Erasing, wait ... 
Erase done, time : 00:04:15 
Write , Start : 0x421C0000 , Len : 0x00DE0000
Flashing , wait ...
Region flash done, time : 00:00:20
Processing Region 2/2
Erase , Start : 0x43E60000 , Len : 0x000E0000
Erasing, wait ... 
Erase done, time : 00:00:07 
No write data, skip
CRC check passed , 0xED62

Flashing done!
Total flash time : 00:08:22
Reboot phone now...

Reading Phone Info....
Connected phone -   Nokia 110
Software Info:     V 03.04 20-04-12 RM-827 (c) Nokia            
IMEI:  353656052976588
PPM version :   V 03.04 20-04-12 RM-827 (c) Nokia             M4
Product code:  059N403
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Processing After Flash Defaults...
FullFactorySet... Ok!
UserDataDefaultsSet...OK!
ServiceDefaultsSet... Ok!
LeaveDefaultsSet... Ok!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Check and Upload User Certificates ...
Total - 42 certs
Certificates found, skip upload ...
AfterFlash operations done ;D
Done!
Connect phone on selected interface...


Elapsed: 00:09:06
Connect phone on selected interface...


Phone found!
Series 40 Device detected!
read info...  - Ok

maanarman · 07-14-2015, 09:40

Code:

Verify files ... 
MAUI : RM-944_ROM_eMP_12.06.11
VIVA : RM-944_VIVA_eMP_12.06.11
LANG : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
CUST : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
JMPT : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
 - > MODE : FullFlash

Dead Mode is Selected
Waiting for USB device...
1. Phone should be Off!
2. Battery must be charged and inserted! ( if not used external power )
 - > If phone can't switch to BL - use battery or flash from Local mode!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 10 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info : 
BB_CPU_ID : 625A
BB_CPU_HW : CA01
BB_CPU_SW : 0001
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6250_S0001
BB_CPU_SN : 870D4EB391AF1578CB19B1D89E26DD7A
BROM Protocol Version : 05
BROM Status : 1012
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : Bree.12.06.11.p1
BROM/BL stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
DA_eMP_Bree.fg
DA_VERIFY : 00
DA_JUMP   : 00040000
DA_INFO   : 0xC0 , Ver : 3.2 , BBID : 0x88
DA_CSTAT  : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00E2 , [WINBOND] W25Q32BV
[0] : FLASH_DIE : 00EF 0040 0016 0000 
[0] : FLASH_LEN : 0x00400000
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
SecureDecrypt : RM-944_ROM_eMP_12.06.11
SecureDecrypt : RM-944_VIVA_eMP_12.06.11
SecureDecrypt : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
SecureDecrypt : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
SecureDecrypt : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
OVRLP : 000069B900000001
PHPID : Bree.12.06.11.p1
OVRLP : 00004DF900000001
DA : FORMAT_BIN
Processing Flash Pre-format
FILES : 5
SAFE_BLOCK : 04
FORMAT_BIN : Ok
ERASE_MAUI_INFO : 0x0001B000
WRITE_STYLE : DEF : 0x01 (SEQ)
Write : RM-944_ROM_eMP_12.06.11
Write : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
Write : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
Write : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
Write : RM-944_VIVA_eMP_12.06.11
CODE_DNLOAD : Ok
[VERIFY] DONE : RM-944_ROM_eMP_12.06.11
[VERIFY] DONE : RM-944_LANG_PACK_ROM_IJ_eMP_12.06.11
[VERIFY] DONE : RM-944_CUSTPACK_ROM_IJ_MEA_PK_eMP_12.06.11
[VERIFY] DONE : RM-944_JUMP_TABLE_IJ_MEA_PK_eMP_12.06.11
[VERIFY] DONE : RM-944_VIVA_eMP_12.06.11
CODE_VERIFY : Ok
Executing FFS FORMAT now...
FAT_RANGE : 0x003A6000-0x003F3FFF , LEN : 0x0004E000
DA_RET   : DA_IN_PROGRESS
DA_RET   : FORMAT_DONE
Rebooting phone now

Flashing done!
Total flash time : 00:01:10
Reboot phone Ok

Connect phone on selected interface...

07-14-2015, 05:30	#23642 (permalink)
srinibas No Life Poster Join Date: Apr 2007 Location: M W Balasore,Odisha,INDIA Age: 52 Posts: 12,752 Member: 492222 Status: Offline Sonork: 100.1594126 Thanks Meter: 10,377	Panasonic P55 MTK 6589 Read Factory Flash file Reading Flash Conent now ... Brand : Panasonic ProdName : P55 ProdModel : Panasonic P55 Device : P55 AndroidVer: 4.4.2 MTKxCPU : MT6589 MTKxPRJ : ALPS.KK1.MP5.V1.5 [Read Ok] : preloader_yulong89_wet_kk.bin [Read Ok] : MBR [Read Ok] : EBR1 [Read Ok] : lk.bin [Read Ok] : boot.img [Read Ok] : recovery.img [Read Ok] : secro.img [Read Ok] : logo.bin [Read Ok] : EBR2 [Read Ok] : autobak.img [Read Ok] : system.img [Read Ok] : cache.img [Read Ok] : userdata.img [ScatCFG] : MT6589 / V1.0.0 / yulong89_wet_kk / EMMC FW Size : 940 MiB Scatter saved to : C:\Documents and Settings\Administrator\Desktop\New Folder (2)\MT6589__Panasonic__Panasonic P55__P55__4.4.2__ALPS.KK1.MP5.V1.5\ All done! Br - srinibas

07-14-2015, 05:41	#23643 (permalink)
srinibas No Life Poster Join Date: Apr 2007 Location: M W Balasore,Odisha,INDIA Age: 52 Posts: 12,752 Member: 492222 Status: Offline Sonork: 100.1594126 Thanks Meter: 10,377	Panasonic P55 MTK 6589 Read Pattern lock code Operation : Read PatternLock [ v1.23 ] 1. Power Off Phone , Remove battery , Insert back 2. Insert USB cable. In some cases require hold BootKey Wait for phone... Phone found! [ 36 ] Sync... Inital regs read done Boot Info : BB_CPU_ID : 6583 BB_CPU_HW : CA01 BB_CPU_SW : 8A00 BB_CPU_SB : 0001 BB_CPU_NM : [MediaTek] MT6583\|6589_S00 Processing BROM stage SecCfgVal : 0x00000000 BromVersion : 0xFF BLVersion : 0x01 Preloader Status : Alive Processing DA stage DA Select done , sending NAND_ID : 00000000000000000000000000000000 eMMC_ID : 4B0001154D565835E975014243212BD0 DA Stat : v3.2 on BBID : 0x86 DA Sent. Configure setting now ... DA started successuflly eMMC FlashIC initialized [eMMC] : FLASH_VEN : 0015 , OEM : 0100 [eMMC] : FLASH_INF : BMVX5 [eMMC] : FLASH_CID : 1501004B3558564D420175E9D02B2143 [eMMC] : FLASH_LEN : 0x00000000E9000000 INT RAM : 0x00020000 EXT RAM : 0x40000000 BOOT TYPE : EMMC_FLASH_BOOT SOC VERIFY : C1 Boot Ok! Reading data ... FS Size : 2511 MiB Magic Ok Mount point : /data Get PatternLock ... PatternLock Sequnce : 14569 Done! Elapsed: 00:00:20 Reconnect Power/Cable!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Unlocking 5190	Ryu	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	23	01-07-2018 17:14
news headlines to gsm phone	mos	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	7	05-22-2016 11:42
my 8810 is phone locked ,can somebody please help	duyphuc	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	18	12-23-2014 09:03
need software for 5161 by cable	mln2000	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	6	08-29-2010 20:17

07-13-2015, 18:06	#23641 (permalink)
ij_cell No Life Poster Join Date: May 2013 Location: TkinterPy,Hex Cal,Ext2,Ext4, Posts: 4,540 Member: 1937038 Status: Offline Sonork: QQ 2045657399 Thanks Meter: 4,492	Nokia e52-1 format and factory setting done. Format File System... Operating mode is OK, no need change... Scanning FS parametres... Checking Data... Detected : 2 drive(s)... Start formating.... Using Series 60 format algorithm... ================================== Formating drive : C now... Step1 : OK Step2 : OK End format... ================================== Formating drive : D now... Step1 : OK Step2 : OK End format... ================================== Done! Resetting selected items... Check phone mode... Phone in Local mode Seting Test mode... wait... Test mode set Settings Full Factory Defaults... Set OK! Settings Software Upgrade Defaults... Set OK! Settings Service Centre Defaults... Set OK! Settings Production Tune Defaults... Set OK! Settings User Data Defaults... Set OK! Settings Leave Factory defaults... Set OK! Elapsed: 00:00:07 Reading Phone Info.... Connected phone - Nokia E52-1 Software ver : V ICPR82_09w36.5 09-10-09 RM-469 (c) Nokia IMEI : 359327030373439 XappVer : 0000082A Ape Ver : 022.009 APE Var : 022.009022.009.12.01022.009.209.03 APE ADSP: 256 DSP Ver : ICPR82_09w36.4_RIO APE Test: 0.068 PPM : CNT : Product SN : MHH947210 Product code : 0588050 Base Prd.code: 0565921 Long Prod.SN : 0 Hardware info======= HWID : 6010 Retu : 40 Tahvo : 00 Batery: 3580 mV APE HW: 256 Lock info =========== IMEI : 359327030373439 IMEI spNet : 3A 95 23 07 03 73 43 03 IMEI svNet : 33 95 23 07 03 73 43 23 F8 Conf key : 0000000000000000 Provider key : 2440700000000000 Country : Finland Operator : NOKIA (Open) Counters : Key 0 [3] , Fbus 0 [10] Blocks : 7 LOCK STATUS : ============================= BLK : 1 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open BLK : 2 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open BLK : 3 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open BLK : 4 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open BLK : 5 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open BLK : 6 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open BLK : 7 Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open ============================= LOCKS : All Open ============================= CRT308 Backup Created SDD key status : Damaged!!!!! CMLA Key status : Not Present SimLock status : Ok Security status : Ok PA_SimLock Version : PA_SL3 phone , SP_CODE_LEN : 15 User code : Crypted UserDataExLevel : Low [Gallery] , FullFlash method Done!