Box is Not IN Needed Mod.How To Solve? - Page 18 - GSM-Forum

RAVI_SINGH · 04-28-2010, 13:00

very simple if box connected and disconnect n reconnect again to box going in needed mod .

zatman · 04-28-2010, 14:32

Quote:

Originally Posted by emmanueldraper

cyclone pls help
Initialization has failed -> No connection was established, or box is not in needed mode
since the new update i receive this problem, i have unstalled and install but problem is still the same
i need yours help quickly.Box Serial Number: C0000809

hola,uninstal all.clean registry ..reboot now instal cyclone installer v 1.6.wait to finish .ok to instal drivers .now conect your cyclone box to an ather usb port no the same one befor.wait finish instal cyclone drivers. after run cyclone soft your pc connected to internet no firewall.go to box maintenance and click... wait to chek card etc....update firm...finish.now close program unplug box .plug it again run cyclone and all must work ok .important use usb port only for cyclone box.BR

utuh · 05-06-2010, 12:16

Code:

HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk27
Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty
Box registration status: Registered OK
Paired Card SN: D1000378
First Name: akbar
Surname: akbar muhammad
Nickname: utamabone
Address: bone
Country: indonesia
E-Mail: [email protected]
Reseller: GPGIndustries, China
Warranty Start Date: 2009-06-02
Warranty Period (months): 6
Warranty Stop Date: 2009-12-02
Warranty active: No
============================
Updating Security Area...
Security Area Update Skipped, Not allowed
Updating Main Firmware...
Main Firmware Update Skipped, Not allowed
Updating COM Emulator Firmware...
COM Emulator Update Skipped, Not allowed
Updating Secure Bootloader...
Secure Bootloader Update Skipped, Not allowed or not needed
Disconnected from Cyclone Server
Box Maintenance finished successfully

can't update box and can't going to main mode ( only can boot loader mode ).

Code:

 Handling device: [Cyclone Team], [Cyclone Bootloader]
Initialization has failed -> No connection was established, or box is not in needed mode

SiRoYa · 05-06-2010, 16:57

Quote:

Originally Posted by utuh

Code:

HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk27
Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty
Box registration status: Registered OK
Paired Card SN: D1000378
First Name: akbar
Surname: akbar muhammad
Nickname: utamabone
Address: bone
Country: indonesia
E-Mail: [email protected]
Reseller: GPGIndustries, China
Warranty Start Date: 2009-06-02
Warranty Period (months): 6
Warranty Stop Date: 2009-12-02
Warranty active: No
============================
Updating Security Area...
Security Area Update Skipped, Not allowed
Updating Main Firmware...
Main Firmware Update Skipped, Not allowed
Updating COM Emulator Firmware...
COM Emulator Update Skipped, Not allowed
Updating Secure Bootloader...
Secure Bootloader Update Skipped, Not allowed or not needed
Disconnected from Cyclone Server
Box Maintenance finished successfully

can't update box and can't going to main mode ( only can boot loader mode ).

Code:

 Handling device: [Cyclone Team], [Cyclone Bootloader]
Initialization has failed -> No connection was established, or box is not in needed mode

reinstall drivers and then update ur box from maintenance tool

br
SiRoYa

jorco_max11 · 05-09-2010, 22:38

Quote:

Originally Posted by SiRoYa

reinstall drivers and then update ur box from maintenance tool

br
SiRoYa

i need fill credits, problem with sever
Started card credits fill procedure at 15:35:46
Handling device: [Cyclone Team], [Cyclone Bootloader]
Handling device: [Cyclone Team], [Cyclone Box]
Checking for card presence...
Security card found with ATR [3BEB0000813120454A434F503331333647445478]
Checking credits...
Card is empty, proceeding with credits fill...
Service Tag: 65BCBD4639E4E38217AF7557C540DA0A
Connecting to Cyclone Server
Card credits fill error -> Can't connect to Cyclone Server

thanks for your help..!

SiRoYa · 05-09-2010, 22:47

Quote:

Originally Posted by jorco_max11

i need fill credits, problem with sever
Started card credits fill procedure at 15:35:46
Handling device: [Cyclone Team], [Cyclone Bootloader]
Handling device: [Cyclone Team], [Cyclone Box]
Checking for card presence...
Security card found with ATR [3BEB0000813120454A434F503331333647445478]
Checking credits...
Card is empty, proceeding with credits fill...
Service Tag: 65BCBD4639E4E38217AF7557C540DA0A
Connecting to Cyclone Server
Card credits fill error -> Can't connect to Cyclone Server

thanks for your help..!

fixed
try again now......

jorco_max11 · 05-09-2010, 22:53

Quote:

Originally Posted by SiRoYa

fixed
try again now......

solved my problem thanks sir SiRoYa

paimai51 · 05-10-2010, 06:43

SiRoYa san,
please help. I had same problem :

Box Maintenance procedure started at 0:44:16
Handling device: [Cyclone Team], [Cyclone Bootloader]
Bootloader: Cyclone Secure Bootloader v2.10, (Dec 5 2009 23:39:04), Type: Signed Production Application
Service Tag: BED4A45BB615E10DED26A055C6318D49
Connecting to Cyclone Server
Cyclone Server (1.0.0.598), Cyclone Box Team 2008, 2009, 2010 - Ready.
========= Box Info =========
Box SN: C000090B
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk27
Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty
Box registration status: Registered OK
Paired Card SN: D00005A1
First Name: Yu
Surname: YL
Nickname: ylyu
Address: saitamake kawagutishi hontyou 3-11-19-702
Country: Japan
E-Mail: [email protected]
Reseller: EM5, China
Warranty Start Date: 2009-05-30
Warranty Period (months): 6
Warranty Stop Date: 2009-11-30
Warranty active: No
============================
Updating Security Area...
Security Area Update Skipped, Not allowed
Updating Main Firmware...
Main Firmware Update Skipped, Not allowed
Updating Secure Bootloader...
Secure Bootloader Update Skipped, Not allowed or not needed
Disconnected from Cyclone Server
Box Maintenance finished successfully

Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: 1.0.0.7828
Handling device: [Cyclone Team], [Cyclone Bootloader]
Initialization has failed -> No connection was established, or box is not in needed mode

SiRoYa · 05-10-2010, 17:34

Quote:

Originally Posted by paimai51

SiRoYa san,
please help. I had same problem :

Box Maintenance procedure started at 0:44:16
Handling device: [Cyclone Team], [Cyclone Bootloader]
Bootloader: Cyclone Secure Bootloader v2.10, (Dec 5 2009 23:39:04), Type: Signed Production Application
Service Tag: BED4A45BB615E10DED26A055C6318D49
Connecting to Cyclone Server
Cyclone Server (1.0.0.598), Cyclone Box Team 2008, 2009, 2010 - Ready.
========= Box Info =========
Box SN: C000090B
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk27
Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty
Box registration status: Registered OK
Paired Card SN: D00005A1
First Name: Yu
Surname: YL
Nickname: ylyu
Address: saitamake kawagutishi hontyou 3-11-19-702
Country: Japan
E-Mail: [email protected]
Reseller: EM5, China
Warranty Start Date: 2009-05-30
Warranty Period (months): 6
Warranty Stop Date: 2009-11-30
Warranty active: No
============================
Updating Security Area...
Security Area Update Skipped, Not allowed
Updating Main Firmware...
Main Firmware Update Skipped, Not allowed
Updating Secure Bootloader...
Secure Bootloader Update Skipped, Not allowed or not needed
Disconnected from Cyclone Server
Box Maintenance finished successfully

Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: 1.0.0.7828
Handling device: [Cyclone Team], [Cyclone Bootloader]
Initialization has failed -> No connection was established, or box is not in needed mode

reinstall drivers and then update ur box from maintenance tool

br
SiRoYa

utuh · 05-13-2010, 08:35

still same probeleme

Quote:

Box Maintenance procedure started at 3:15:47 PM
Handling device: [Cyclone Team], [Cyclone Bootloader]
Bootloader: Cyclone Secure Bootloader v2.10, (Dec 5 2009 23:39:04), Type: Signed Production Application
Service Tag: EBBF8572DEBBBC3C4A8A5AA1D28DA0D4
Connecting to Cyclone Server
Cyclone Server (1.0.0.598), Cyclone Box Team 2008, 2009, 2010 - Ready.
========= Box Info =========
Box SN: C000080A
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk27
Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty
Box registration status: Registered OK
Paired Card SN: D1000378
First Name: akbar
Surname: akbar muhammad
Nickname: utamabone
Address: bone
Country: indonesia
E-Mail: [email protected]
Reseller: GPGIndustries, China
Warranty Start Date: 2009-06-02
Warranty Period (months): 6
Warranty Stop Date: 2009-12-02
Warranty active: No
============================
Updating Security Area...
Security Area Update Skipped, Not allowed
Updating Main Firmware...
Main Firmware Update Skipped, Not allowed
Updating COM Emulator Firmware...
COM Emulator Update Skipped, Not allowed
Updating Secure Bootloader...
Secure Bootloader Update Skipped, Not allowed or not needed
Disconnected from Cyclone Server
Box Maintenance finished successfully

Quote:

Handling device: [Cyclone Team], [Cyclone Bootloader]
Initialization has failed -> No connection was established, or box is not in needed mode

cezzure · 05-15-2010, 14:21

turn off all antivirus. i,ve installed v106 and i'm using symantec antivirus, there is a file have been detected as a virus. so i'm turn off my antivirus and installation are done and the mighty "CYLONE BOX" box are working normally as i've maintenance box.

akbar muhammad · 05-17-2010, 14:58

Quote:

Originally Posted by cezzure

turn off all antivirus. i,ve installed v106 and i'm using symantec antivirus, there is a file have been detected as a virus. so i'm turn off my antivirus and installation are done and the mighty "CYLONE BOX" box are working normally as i've maintenance box.

I'm turn off antivirus and istallation....
Still same problem.

HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk27
Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty
Box registration status: Registered OK
Paired Card SN: D1000378
First Name: akbar
Surname: akbar muhammad
Nickname: utamabone
Address: bone
Country: indonesia
E-Mail: [email protected]
Reseller: GPGIndustries, China
Warranty Start Date: 2009-06-02
Warranty Period (months): 6
Warranty Stop Date: 2009-12-02
Warranty active: No
============================
Updating Security Area...
Security Area Update Skipped, Not allowed
Updating Main Firmware...
Main Firmware Update Skipped, Not allowed
Updating COM Emulator Firmware...
COM Emulator Update Skipped, Not allowed
Updating Secure Bootloader...
Secure Bootloader Update Skipped, Not allowed or not needed
Disconnected from Cyclone Server
Box Maintenance finished successfully

SiRoYa · 05-17-2010, 23:25

Quote:

Originally Posted by utuh

still same probeleme

Update ur box again .............

SiRoYa · 05-17-2010, 23:25

Quote:

Originally Posted by akbar muhammad

I'm turn off antivirus and istallation....
Still same problem.

HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk27
Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty
Box registration status: Registered OK
Paired Card SN: D1000378
First Name: akbar
Surname: akbar muhammad
Nickname: utamabone
Address: bone
Country: indonesia
E-Mail: [email protected]
Reseller: GPGIndustries, China
Warranty Start Date: 2009-06-02
Warranty Period (months): 6
Warranty Stop Date: 2009-12-02
Warranty active: No
============================
Updating Security Area...
Security Area Update Skipped, Not allowed
Updating Main Firmware...
Main Firmware Update Skipped, Not allowed
Updating COM Emulator Firmware...
COM Emulator Update Skipped, Not allowed
Updating Secure Bootloader...
Secure Bootloader Update Skipped, Not allowed or not needed
Disconnected from Cyclone Server
Box Maintenance finished successfully

Update ur box again .............

bogym · 05-20-2010, 18:38

sorry, but same problem

Box Maintenance procedure started at 8:36:54 PM
Handling device: [Cyclone Team], [Cyclone Bootloader]
Bootloader: Cyclone Secure Bootloader v2.10, (Dec 5 2009 23:39:04), Type: Signed Production Application
Service Tag: 81CD58B2DF658A3D692E8100681BEC98
Connecting to Cyclone Server
Cyclone Server (1.0.0.598), Cyclone Box Team 2008, 2009, 2010 - Ready.
========= Box Info =========
Box SN: C0003763
HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2009, wk40
Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty
Box registration status: Registered OK
Paired Card SN: D90001E7
First Name: bogdan
Surname: macovei
Nickname: bogym05
Address: dorohoi
Country: romania
E-Mail: [email protected]
Reseller: OvidelGSM, Romania
Warranty Start Date: 2010-02-17
Warranty Period (months): 6
Warranty Stop Date: 2010-08-17
Warranty active: Yes
============================
Updating Security Area...
Security Area Update Skipped, Not allowed
Updating Main Firmware...
Main Firmware Update Skipped, Not allowed
Updating COM Emulator Firmware...
COM Emulator Update Skipped, Not allowed
Updating Secure Bootloader...
Secure Bootloader Update Skipped, Not allowed or not needed
Disconnected from Cyclone Server
Box Maintenance finished successfully

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
problem with my cyclone box.box is not in needed mode	samih127	Cyclonebox	18	06-12-2010 06:05
Box is not in needed mode [SOLVED]	renren	Cyclonebox	2	01-19-2010 22:38
::solve:: box is not in needed mode	mr khalid	Cyclonebox	6	09-15-2009 08:36
Cyclone team (not connected) box is not in needed mode	tims	Cyclonebox	17	06-29-2009 03:54
Box is not in needed mode.	masterunlock	Cyclonebox	5	03-24-2009 16:44

04-28-2010, 13:00	#256 (permalink)
RAVI_SINGH Registered User Join Date: Dec 2009 Location: p A k I s T a N Posts: 1,400 Member: 1178981 Status: Offline Sonork: 100.1596342 Thanks Meter: 500	very simple if box connected and disconnect n reconnect again to box going in needed mod .

05-10-2010, 06:43	#263 (permalink)
paimai51 Freak Poster Join Date: Sep 2005 Age: 58 Posts: 188 Member: 178483 Status: Offline Thanks Meter: 4	SiRoYa san, please help. I had same problem : Box Maintenance procedure started at 0:44:16 Handling device: [Cyclone Team], [Cyclone Bootloader] Bootloader: Cyclone Secure Bootloader v2.10, (Dec 5 2009 23:39:04), Type: Signed Production Application Service Tag: BED4A45BB615E10DED26A055C6318D49 Connecting to Cyclone Server Cyclone Server (1.0.0.598), Cyclone Box Team 2008, 2009, 2010 - Ready. ========= Box Info ========= Box SN: C000090B HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2008, wk27 Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty Box registration status: Registered OK Paired Card SN: D00005A1 First Name: Yu Surname: YL Nickname: ylyu Address: saitamake kawagutishi hontyou 3-11-19-702 Country: Japan E-Mail: [email protected] Reseller: EM5, China Warranty Start Date: 2009-05-30 Warranty Period (months): 6 Warranty Stop Date: 2009-11-30 Warranty active: No ============================ Updating Security Area... Security Area Update Skipped, Not allowed Updating Main Firmware... Main Firmware Update Skipped, Not allowed Updating Secure Bootloader... Secure Bootloader Update Skipped, Not allowed or not needed Disconnected from Cyclone Server Box Maintenance finished successfully Nokia DCT4/WD2/BB5 Service Tool Initialization Started, Engine Revision: 1.0.0.7828 Handling device: [Cyclone Team], [Cyclone Bootloader] Initialization has failed -> No connection was established, or box is not in needed mode

05-15-2010, 14:21	#266 (permalink)
cezzure Junior Member Join Date: Jun 2007 Location: Indonesia Posts: 18 Member: 527563 Status: Offline Thanks Meter: 4	turn off all antivirus. i,ve installed v106 and i'm using symantec antivirus, there is a file have been detected as a virus. so i'm turn off my antivirus and installation are done and the mighty "CYLONE BOX" box are working normally as i've maintenance box.

05-20-2010, 18:38	#270 (permalink)
bogym Freak Poster Join Date: Jan 2004 Location: Romania Age: 42 Posts: 122 Member: 48872 Status: Offline Thanks Meter: 2	sorry, but same problem Box Maintenance procedure started at 8:36:54 PM Handling device: [Cyclone Team], [Cyclone Bootloader] Bootloader: Cyclone Secure Bootloader v2.10, (Dec 5 2009 23:39:04), Type: Signed Production Application Service Tag: 81CD58B2DF658A3D692E8100681BEC98 Connecting to Cyclone Server Cyclone Server (1.0.0.598), Cyclone Box Team 2008, 2009, 2010 - Ready. ========= Box Info ========= Box SN: C0003763 HW Revision: A, Suitable for: Production, Case: First Plastic Case, MCU Manufacture Time: 2009, wk40 Set: Box, TX2 Adapter, 100 Credits, 6 Months Warranty Box registration status: Registered OK Paired Card SN: D90001E7 First Name: bogdan Surname: macovei Nickname: bogym05 Address: dorohoi Country: romania E-Mail: [email protected] Reseller: OvidelGSM, Romania Warranty Start Date: 2010-02-17 Warranty Period (months): 6 Warranty Stop Date: 2010-08-17 Warranty active: Yes ============================ Updating Security Area... Security Area Update Skipped, Not allowed Updating Main Firmware... Main Firmware Update Skipped, Not allowed Updating COM Emulator Firmware... COM Emulator Update Skipped, Not allowed Updating Secure Bootloader... Secure Bootloader Update Skipped, Not allowed or not needed Disconnected from Cyclone Server Box Maintenance finished successfully