**** HTC Desire(Bravo) PB9920000 Unlock/Repair mega thread **** finally! see here: RIFF JTAG – HTC Desire Unlock, Unbrick, IMEI repair supported http://www.jtagbox.com/wp-content/up...htc-desire.jpg R-Team, can Riff Jtag repair or revive my dead boot HTC Desire? i have one here, accidentally disconnected when updating ROM now it's totally dead.. and i've been waiting NEWS from Riff JTAG to support this Model.. please confirm if RIFF Jtag can Repair/Revive my HTC Desire? More Power RIFF JTAG Rocker Team! Br. Jap |
Sure 100% can repair Dead boot HTC Desire I have repair succeed one B.r Xiaoyuz |
and how to flash it after unbrick to get it back working? |
Quote:
br http://i72.photobucket.com/albums/i1...Other/PIC1.png http://a0.twimg.com/a/1280256900/ima...ogo_header.png |
Quote:
Quote:
how to flash after unbrick to get it back working???? planning to buy riff box this week.. ;) Br. Jap |
Quote:
|
ckeck after repair how to flash flash it with riff box or any other procedure |
after repair it has carrier: ASIA HK CHK so i think we need a ship rom from this, but i found only one witch have same id, but the problem is that this updater says that bootloader newer then the one i will try to flash... wrong booloader: failed! i used this rom: RUU_Bravo_hTC_Asia_HK_CHT_1.01.832.1_Radio_32.26.0 0.24U_4.04.00.03_2_test_132015.exe till now, i got it not back working :( and the main problem is, when the phone dont start up, how i can create a goldcard? with a goldcard it should be possible to flash it with any rom. |
see this Quote:
see more here [TUT]Complete upgrading guide(root, unroot, flashing ROM & updates) Br |
problem is, that recovery mode is not working, it hangs also on htc 3 green chars. |
Quote:
mine is Hang on HTC Logo but i can enter Hboot or fastboot mode (holding volume down and power button) that's why i tried to flash the rom before with wrong procedure and now HTC Desire is DEAD BOOT |
another htc but similar problem http://forum.gsmhosting.com/vbb/6215219-post9.html if possible try to search desire image without boot |
Quote:
To generate GOLD card you no need working HTC desire. You need other HTC on windows mobile that is supported by SW to generation gold card and need use this phone NOT HTC DESIRE !! !! |
thanks wgmmmx1 devo sayed this to me today too... i taught the number is uniqe for every device and i can create a gold card only for the one device witch i whant to use it.. now its clear... with a goldcard it should be easy possible to repair it now ;) i will test it later and post the result / instructions if it works. so i think, repairing the desire now should be no problem with goldcard... |
pro, at the moment, you repair your desire back again working? what bootloader of desire after repair by riffbox? |
yessss... the bricked htc desire is now back to live ;) build a goldcard (can use any other htc, dont need same one like i tought before) and update via sd card using any rom you wish. thats it! ;) bootloader after repair is: 0.80.0000 |
Quote:
|
Quote:
|
HTC Desire repair problem |
1.) try to hold power while start connection 2.) check cables for shorts 3.) check cables for correct pinouts 4.) sometimes you need to try some more time to resurrect 5.) RTCK Sample speed set to max (sometimes i set the first box to 4Mhz and it worked) |
i repair it ok, pro, how to update it back again working. Rom you use to update it? rom in htc desire before die WWE_2.09.405.8? |
with a goldcard you can write any rom into it.. i used the latest unbrandet rom available. 1.) make goldcard with your sd card 2.) copy the rom rename it to: PB99IMG.zip start with back button and power on button pressed, wait a short time and your htc will check the sd card and will start with update... press vol. up button to say yes to update.. waiting short time... and htc is working again ;) |
after you made your goldcard copy this image: RapidShare: 1-CLICK Web hosting - Easy Filehosting to your sd card. (dont change the name and dont try to unpack it) just copy it like it is to your sd card. then all should go well... |
pro hboot your htc? 0.83 or 0.92 or 0.93 I try update via goldcard and PB99IMG.zip or try [HOWTO] Downgrade Froyo (2.2) to Stock 2.1 (ANY HBOOT | WIN/LINUX/MAC | ROOT) - xda-developers My htc sometimes restart or not power on :( What problem? i try update with PB99IMG.zip [1] radio_v2 fail PU [2] radio_cust ok . . . Partion update fail Radio of your htc?:) |
Quote:
|
Quote:
i have gold card already, firmware or rom please share and simple guide to get it back working again BIG THANKS wbr, Jap |
Quote:
|
Jtag Desire problem Tryed for a few times, checked all wires are good, still recieve an error: Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.13, JTAG Manager Version: 1.14 Selected Resurrector: [HTC Desire] Connecting to the dead body...OK Detected dead body ID: 0x202400E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...FAILED ERROR: Communication is not established. Terminating. Any ideas pls?!! |
hardware fault , and i hope you make all like you read in resurections-help-manual |
i have the same problem with desire. (its working phone, needs unlock.) is it riffbox hw problem or phone? |
Quote:
can any one answer of this qesions? |
Quote:
ps: a riff 0.80 boot-ot ír rá ha nincs egy tutira müködő golcard-d megbaszhatod, mert csak recovery menü lesz, szal szerintem először nézd át a flashelést egyebeket, ha nagyon nem jutsz előre szombaton kispesten leszek |
i have similar problem :( just theoretical :) possible to upgrade the desire dll? If the phone work and we will only unlock the phone we know the h-boot ver. Before make the resurrection simply tick the right h-bbot version (0.75, 0.80, 0.92, 0.93) and no need upgrade-downgrade and this "funny" goldcard or ADB. thx |
cable problem can be too . and frequenz may need low be . like 4MHz or 1MHz |
[SOLVED] New Desire with SLCD display problem hi RIFF BOX tean i had fully working HTC Desire.i unlock it sucsacfully . here is log Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.13, JTAG Manager Version: 1.14 Selected Resurrector: [HTC Desire] Connecting to the dead body...OK Detected dead body ID: 0x202400E1 - CORRECT! Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x55BC (512MB) Flashing the dead body...OK Resurrection complete! and now the fone is dead. when i press power the fone vibrat and the LCD does nt light on.just blank LCD.if i connet to PC it detact HTC bootloader. the fone is fully fine and there is now hardwear problem or any damge on the fone. please help me.if any body have bin file can u give me link. please hlep RIFF BOX team. :( |
A noob to Riff myself, but HTC.. Love 'em. Press and hold the back button, now press the power button for a couple of seconds. Do you get the fastboot menu? If so, you just need to flash the Desire via the goldcard method.. Plenty of posts regarding flashing via goldcard on this forum.. Hope this helps |
no i do nt get anything on LCD nothing the LCD doesnt light on.no i dont get fastboot menu . |
Quote:
|
did you checked all two checkboxes? did you entered the original imei of the device? resurrect it again to make shure all is okay, so it can enter the fastboot menu, after this make a goldcard with any other htc device for desire... sd card need to be formated as fat32! to make goldcard: i prefere psas, because you can make unlimited security level but if you have axe box you can make goldcards to, but only with security level of 5. (means you can only use it 5 times). psas / qmat also offers free goldcard creation website, just search for it with google and you will find it fast. upload the image witch i already posted for download and copy it like it is to the sd card... now enter bootloader menu (not fastboot menu) and wait till bootloader checks sd card content, it will now start to check and see if sign is okay, if your goldcard is okay it will now ask you to update your device, navigate witch the volium keys to "yes" and it will start to update your htc. after update it should work again and is fully unlocked ;) |
Hi, This is new board with SLCD instead of Amoled. Hence, old bootloader wont show aynthing on display. We have solution for this problem, and its being tested now. To repair new Desire, restoring new version of SPL is required. 1. Download full backup file and unpack it 2. Start JTAG Manager, select HTC Desire 3. Set everything exactly like on "restore-original-spl.jpg" 4. Press "Write" - after this phone should normaly enter download mode Required files You can download from here. This is just quick fix, next week we will add optional SPL version selection. |
New boards with this new display have these markings : 2010/6/10 50H00618 - 18M - D |
yes the problem solve 100% thans legija for all hard work. :) |
Quote:
But similar htc hd2 512. Htc desire repair ok after update restart 10 or 15 minutes |
I built jig now its ok but the Device not yet entered boothttp://forum.gsmhosting.com/vbb/imag.../separator.gif |
now its ok but the Device not yet entered boo |
Quote:
New boards with this new display have these markings : 2010/6/10 50H00618 - 18M - D |
unlock problem desire Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.13, JTAG Manager Version: 1.14 Selected Resurrector: [HTC Desire] Connecting to the dead body...OK Detected dead body ID: 0x202400E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...FAILED ERROR: Communication is not established. Terminating help me i m new here |
daptive Clocking RTCK Sampling is: [Sample at MAX] make simple at 4 Mhz or 1MHz and reply |
thanx sen-i problem solve |
[SOLVED] nOOb: How to unlock desire AMOLED with RIFF? i just bought new Riff jtag box, and try to unlock Desire i solder wires like in pinout i connect phone with cable, click unlock and manager info: Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.13, JTAG Manager Version: 1.14 Selected Resurrector: [HTC Desire] Connecting to the dead body... ERROR: Set I/O Voltage to 2.60V failed. Real reading is 3.77V http://img178.imageshack.us/img178/7787/imag0019i.jpg also i try with other cable, try with low frequency and still same :/ |
All times are GMT +1. The time now is 04:44. |
vBulletin Optimisation provided by
vB Optimise (Pro) -
vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -