Post here success logs with RIFF JTAG Manager 1.64 and fw 1.41 - Page 54 - GSM-Forum

delchoni · 09-14-2011, 15:22

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [Samsung Galaxy Tab]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...OK
Resurrection complete!

p1000 galaxy tab

MOHIT_THAREJA · 09-14-2011, 18:03

again huawei c2830 recover done

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [Huawei C2830]

Connecting to the dead body...OK
Detected dead body ID: 0x122CE0E1 - CORRECT!
Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Settings Code: 0x0900010000400000000000000026

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0020/0x88C0 (8MB)

Writting FLASH1 memory from 0x0000000000 to 0x00007FFFFF
Completed in 00:06:08.000 (Average Transfer Rate: 22.26 kB/s)

M0YAL · 09-15-2011, 08:11

[9/15/2011 11:34:02 AM] Open serial port...OK
[9/15/2011 11:34:02 AM] Connecting to the RIFF Box...OK
[9/15/2011 11:34:02 AM] Firmware Version: 1.26, JTAG Manager Version: 1.35
[9/15/2011 11:34:02 AM] Selected Resurrector: [QSC1100 X14]
[9/15/2011 11:34:02 AM]
[9/15/2011 11:34:02 AM] Connecting to the dead body...OK
[9/15/2011 11:34:02 AM] Detected dead body ID: 0x122CE0E1 - CORRECT!
[9/15/2011 11:34:02 AM] Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK
[9/15/2011 11:34:02 AM] Adaptive Clocking RTCK Sampling is: [Sample at MAX]
[9/15/2011 11:34:02 AM] Settings Code: 0x0000010001000000000000000034
[9/15/2011 11:34:02 AM]
[9/15/2011 11:34:02 AM] Resurrection sequence started.
[9/15/2011 11:34:02 AM] Establish communication with the phone...OK
[9/15/2011 11:34:02 AM] Initializing internal hardware configuration...OK
[9/15/2011 11:34:02 AM] Uploading resurrector data into memory...OK
[9/15/2011 11:34:02 AM] Starting communication with resurrector...OK
[9/15/2011 11:34:02 AM]
[9/15/2011 11:34:02 AM] Detected an Initialized FLASH1 Chip, ID: 0x0020/0x882E (16MB)
[9/15/2011 11:34:02 AM]
[9/15/2011 11:34:02 AM] Writting FLASH1 memory from 0x0000000000 to 0x0000FFFFFF
[9/15/2011 11:34:02 AM] Completed in 00:04:57.219 (Average Transfer Rate: 55.12 kB/s)
[9/15/2011 11:34:02 AM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]

M0YAL · 09-15-2011, 12:15

[9/15/2011 1:27:58 PM] Open serial port...OK
[9/15/2011 1:27:58 PM] Connecting to the RIFF Box...OK
[9/15/2011 1:27:58 PM] Firmware Version: 1.26, JTAG Manager Version: 1.35
[9/15/2011 1:27:58 PM] Selected Resurrector: [QSC60XX L20 D08]
[9/15/2011 1:27:58 PM]
[9/15/2011 1:27:58 PM] Connecting to the dead body...OK
[9/15/2011 1:27:58 PM] Detected dead body ID: 0x220B10E1 - CORRECT!
[9/15/2011 1:27:58 PM] Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
[9/15/2011 1:27:58 PM] Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
[9/15/2011 1:27:58 PM] Settings Code: 0x0900010000800000000000000034
[9/15/2011 1:27:58 PM]
[9/15/2011 1:27:58 PM] Resurrection sequence started.
[9/15/2011 1:27:58 PM] Establish communication with the phone...OK
[9/15/2011 1:27:58 PM] Initializing internal hardware configuration...OK
[9/15/2011 1:27:58 PM] Uploading resurrector data into memory...OK
[9/15/2011 1:27:58 PM] Starting communication with resurrector...OK
[9/15/2011 1:27:58 PM]
[9/15/2011 1:27:58 PM] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x257E (8MB)
[9/15/2011 1:27:58 PM]
[9/15/2011 1:27:58 PM] Writting FLASH1 memory from 0x0000000000 to 0x00007FFFFF
[9/15/2011 1:27:58 PM] ERROR: Timeout while waiting for DCC Loader response. Trying to recover...
[9/15/2011 1:27:58 PM] Settings Code: 0x0900010000800000000000000034OK
[9/15/2011 1:27:58 PM] Completed in 00:05:16.735 (Average Transfer Rate: 25.86 kB/s)
[9/15/2011 1:27:58 PM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]

M0YAL · 09-15-2011, 12:29

[9/15/2011 4:57:35 PM] Connecting to the dead body...OK
[9/15/2011 4:57:35 PM] Detected dead body ID: 0x220B10E1 - CORRECT!
[9/15/2011 4:57:35 PM] Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK
[9/15/2011 4:57:35 PM] Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
[9/15/2011 4:57:35 PM] Settings Code: 0x0900010000800000000000000034
[9/15/2011 4:57:35 PM]
[9/15/2011 4:57:35 PM] Resurrection sequence started.
[9/15/2011 4:57:35 PM] Establish communication with the phone...OK
[9/15/2011 4:57:35 PM] Initializing internal hardware configuration...OK
[9/15/2011 4:57:35 PM] Uploading resurrector data into memory...OK
[9/15/2011 4:57:35 PM] Starting communication with resurrector...OK
[9/15/2011 4:57:35 PM]
[9/15/2011 4:57:35 PM] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x257E (8MB)
[9/15/2011 4:57:35 PM]
[9/15/2011 4:57:35 PM] Writting FLASH1 memory from 0x0000000000 to 0x00007FFFFF
[9/15/2011 4:57:35 PM] Completed in 00:04:33.704 (Average Transfer Rate: 29.93 kB/s)
[9/15/2011 4:57:35 PM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]

gsm_ritesh · 09-15-2011, 12:30

haier c2076 dead recover

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [Haier C2076]

Connecting to the dead body...OK
Detected dead body ID: 0x220B10E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x257E (8MB)
Flashing the dead body...OK
Resurrection complete!

**Dipendra Pathak** · 09-16-2011, 03:38

Uploaded with ImageShack.us

MOHIT_THAREJA · 09-16-2011, 15:52

huawei c2206 recover done

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [QSC60XX L20 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x200B10E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Settings Code: 0x0900010000400000000000000026

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x257E (4MB)

Writting FLASH1 memory from 0x0000000000 to 0x00003FFFFF
Completed in 00:02:30.797 (Average Transfer Rate: 27.16 kB/s)

s.alam · 09-16-2011, 17:35

http://img148.imageshack.us/img148/9027/3500p.png

s.alam · 09-16-2011, 17:36

yfrog Photo : http://yfrog.com/443500pp Shared by

shameerphasan78 · 09-16-2011, 19:57

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [USB Modem E153U]

Connecting to the dead body...OK
Detected dead body ID: 0x301C00E1 - IGNORED!
Set I/O Voltage reads as 3.01V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Settings Code: 0x0000010008000000000000000025

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00AD/0x00A1 (128MB)

Writting FLASH1 memory from 0x0000000000 to 0x0007FFFFFF
ERROR: DCC Loader has reported Error Code = 0x22 (0x000000). Trying to recover...
Settings Code: 0x0000010008000000000000000025OK
Completed in 00:11:01.117 (Average Transfer Rate: 204.45 kB/s)

THANKS rocker team

Shoxa · 09-17-2011, 12:55

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [Samsung S5560i]

Connecting to the dead body...OK
Detected dead body ID: 0x07926F0F - CORRECT!
Set I/O Voltage reads as 2.98V, TCK Frequency is 4 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0040 (256MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB

Flashing the dead body...OK
Resurrection complete!

MOHIT_THAREJA · 09-19-2011, 08:36

huawei c2206 recover done

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [QSC60XX L20 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x200B10E1 - CORRECT!
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Settings Code: 0x0900010000400000000000000026

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x017E/0x221A (4MB)

Writting FLASH1 memory from 0x0000000000 to 0x00003FFFFF
Completed in 00:03:16.094 (Average Transfer Rate: 20.89 kB/s)

MOHIT_THAREJA · 09-19-2011, 10:22

huawei c2605 recover done

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.35
Selected Resurrector: [QSC60XX L20 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x200B10E1 - CORRECT!
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Settings Code: 0x0900010000400000000000000026

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0089/0x8852 (4MB)

Writting FLASH1 memory from 0x0000000000 to 0x00003FFFFF
Completed in 00:03:12.469 (Average Transfer Rate: 21.28 kB/s)

M0YAL · 09-19-2011, 12:56

[9/19/2011 5:20:30 PM] Open serial port...OK
[9/19/2011 5:20:30 PM] Connecting to the RIFF Box...OK
[9/19/2011 5:20:30 PM] Firmware Version: 1.26, JTAG Manager Version: 1.35
[9/19/2011 5:20:30 PM] Selected Resurrector: [QSC60XX L20 D08]
[9/19/2011 5:20:30 PM]
[9/19/2011 5:20:30 PM] Connecting to the dead body...OK
[9/19/2011 5:20:30 PM] Detected dead body ID: 0x220B10E1 - CORRECT!
[9/19/2011 5:20:30 PM] Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK
[9/19/2011 5:20:30 PM] Adaptive Clocking RTCK Sampling is: [Sample at MAX]
[9/19/2011 5:20:30 PM] Settings Code: 0x0000010000800000000000000034
[9/19/2011 5:20:30 PM]
[9/19/2011 5:20:30 PM] Resurrection sequence started.
[9/19/2011 5:20:30 PM] Establish communication with the phone...OK
[9/19/2011 5:20:30 PM] Initializing internal hardware configuration...OK
[9/19/2011 5:20:30 PM] Uploading resurrector data into memory...OK
[9/19/2011 5:20:30 PM] Starting communication with resurrector...OK
[9/19/2011 5:20:30 PM]
[9/19/2011 5:20:30 PM] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x257E (8MB)
[9/19/2011 5:20:30 PM]
[9/19/2011 5:20:30 PM] Writting FLASH1 memory from 0x0000000000 to 0x00007FFFFF
[9/19/2011 5:20:30 PM] Completed in 00:02:23.671 (Average Transfer Rate: 57.02 kB/s)
[9/19/2011 5:20:30 PM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]

09-16-2011, 03:38	#802 (permalink)
Dipendra Pathak Product Manager Join Date: Apr 2008 Location: Whitehole throught Blackhole! Posts: 9,582 Member: 747989 Status: Offline Sonork: 100.1593052 Thanks Meter: 8,623	ZTE S1602 New Version Successfully Unlocked Uploaded with ImageShack.us

09-16-2011, 17:35	#804 (permalink)
s.alam Banned Join Date: Jan 2011 Location: NO LOCATION Age: 44 Posts: 609 Member: 1482984 Status: Offline Thanks Meter: 60	try.......................................... http://img148.imageshack.us/img148/9027/3500p.png

09-14-2011, 15:22	#796 (permalink)
delchoni No Life Poster Join Date: Mar 2006 Location: Bulgaria Asenovgrad Age: 42 Posts: 3,197 Member: 239176 Status: Offline Sonork: 100.1602815 Thanks Meter: 851	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [Samsung Galaxy Tab] Connecting to the dead body...OK Detected dead body ID: 0x1BA00477 - CORRECT! Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB) Flashing the dead body...OK Resurrection complete! p1000 galaxy tab

09-14-2011, 18:03	#797 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	again huawei c2830 recover done Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [Huawei C2830] Connecting to the dead body...OK Detected dead body ID: 0x122CE0E1 - CORRECT! Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Settings Code: 0x0900010000400000000000000026 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0020/0x88C0 (8MB) Writting FLASH1 memory from 0x0000000000 to 0x00007FFFFF Completed in 00:06:08.000 (Average Transfer Rate: 22.26 kB/s)

09-15-2011, 12:30	#801 (permalink)
gsm_ritesh Freak Poster Join Date: Sep 2010 Location: indore Posts: 301 Member: 1396867 Status: Offline Thanks Meter: 48	haier c2076 dead recover Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [Haier C2076] Connecting to the dead body...OK Detected dead body ID: 0x220B10E1 - CORRECT! Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x257E (8MB) Flashing the dead body...OK Resurrection complete!

09-16-2011, 15:52	#803 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	huawei c2206 recover done Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [QSC60XX L20 D08] Connecting to the dead body...OK Detected dead body ID: 0x200B10E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Settings Code: 0x0900010000400000000000000026 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x257E (4MB) Writting FLASH1 memory from 0x0000000000 to 0x00003FFFFF Completed in 00:02:30.797 (Average Transfer Rate: 27.16 kB/s)

09-16-2011, 17:36	#805 (permalink)
s.alam Banned Join Date: Jan 2011 Location: NO LOCATION Age: 44 Posts: 609 Member: 1482984 Status: Offline Thanks Meter: 60	yfrog Photo : http://yfrog.com/443500pp Shared by

09-16-2011, 19:57	#806 (permalink)
shameerphasan78 Freak Poster Join Date: Jan 2010 Location: INDIA-KL Posts: 289 Member: 1207179 Status: Offline Thanks Meter: 119	Huawei e173 Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [USB Modem E153U] Connecting to the dead body...OK Detected dead body ID: 0x301C00E1 - IGNORED! Set I/O Voltage reads as 3.01V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Settings Code: 0x0000010008000000000000000025 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00AD/0x00A1 (128MB) Writting FLASH1 memory from 0x0000000000 to 0x0007FFFFFF ERROR: DCC Loader has reported Error Code = 0x22 (0x000000). Trying to recover... Settings Code: 0x0000010008000000000000000025OK Completed in 00:11:01.117 (Average Transfer Rate: 204.45 kB/s) THANKS rocker team

09-17-2011, 12:55	#807 (permalink)
Shoxa No Life Poster Join Date: Feb 2010 Age: 36 Posts: 498 Member: 1245190 Status: Offline Sonork: 100.1606901 Thanks Meter: 204	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [Samsung S5560i] Connecting to the dead body...OK Detected dead body ID: 0x07926F0F - CORRECT! Set I/O Voltage reads as 2.98V, TCK Frequency is 4 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0040 (256MB) Selected Resurrection Data for the NAND Chip with Page size = 2KB Flashing the dead body...OK Resurrection complete!

09-19-2011, 08:36	#808 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	huawei c2206 recover done Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [QSC60XX L20 D08] Connecting to the dead body...OK Detected dead body ID: 0x200B10E1 - CORRECT! Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Settings Code: 0x0900010000400000000000000026 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x017E/0x221A (4MB) Writting FLASH1 memory from 0x0000000000 to 0x00003FFFFF Completed in 00:03:16.094 (Average Transfer Rate: 20.89 kB/s)

09-19-2011, 10:22	#809 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	huawei c2605 recover done Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.35 Selected Resurrector: [QSC60XX L20 D08] Connecting to the dead body...OK Detected dead body ID: 0x200B10E1 - CORRECT! Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Settings Code: 0x0900010000400000000000000026 Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0089/0x8852 (4MB) Writting FLASH1 memory from 0x0000000000 to 0x00003FFFFF Completed in 00:03:12.469 (Average Transfer Rate: 21.28 kB/s)