j100h too many error writing has been stop - GSM-Forum

engcobocell · 06-18-2018, 06:40

hi
am facing these problem please can anyone help me out
am new user for easy jtag plus
Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 Mhz
CMD Pullup Level: 1824 mV
CMD Active Level: 1865 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110190A76A6082A5
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_90A76A60_20180617_222504.extcsd
EMMC Init completed.

Opening file: J13G.pit

Pit: J13G.pit
Entry count: 29

The size of the last section has been updated

BL_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5
The list of files in the firmware:
spl.img
sboot.bin
sboot2.bin
param.lfs

AP_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5
The list of files in the firmware:
boot.img
recovery.img
system.img

CP_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5
The list of files in the firmware:
sprdcp.img
sprddsp.img
nvitem.bin

CSC_OXE_J100HOXE0AQA1_CL1167865_QB12130539_REV01_u ser_low_ship.tar.md5
The list of files in the firmware:
j13g.pit
cache.img
hidden.img

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 Mhz
CMD Pullup Level: 1824 mV
CMD Active Level: 1865 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110190A76A6082A5
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_90A76A60_20180617_222535.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #1
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #2
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #3
Too many errors. Writing has been stopped

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 Mhz
CMD Pullup Level: 1806 mV
CMD Active Level: 1865 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110190A76A6082A5
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_90A76A60_20180617_223145.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #1
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #2
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #3
Too many errors. Writing has been stopped

engcobocell · 06-18-2018, 11:30

snyone can help me please
thanks in advance

pai_d · 06-18-2018, 12:59

You cannot writes data to that EMMC.

Soft doesn't support or EMMC is BAD.

it's SKHINIX emmc. try to uni-format/reset & repartitions.

But it's not guaranteed the handset will ok for a long time.
some time it just ok a week or even a day.

engcobocell · 06-19-2018, 07:12

and now these showing am sorry am new with JTAG
Loading eMMC GEN2 Firmware... IO: 2800 mV
Box S/N: 16F03C9E6AE1BE10, ,FW Ver.: 02.23
CMD Pullup Level:2186 mV
CMD Active Level:2551 mV
Box IO Level:2800 mV
CLK Rate:24000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
---------- eMMC Device Information ----------

EMMC CID : 90014A4834473262110190A76A6082A5
EMMC CSD : D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 08/2015 Rev.0x1
EMMC NAME: H4G2b , S/N: 2426890848
EMMC NAME (HEX): 48344732622000
EMMC ROM1 (Main User Data) Capacity: 3728 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: H4G2b _2426890848_20180618_2255.extcsd
Done.

Checking NAND Image : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Autodetected RAW data
Warning! Disk size is smaller than the main header indicates! Loading
Caution: invalid backup GPT header, but valid main header!
EFI Table CRC Check FAIL.
Warning! One or more CRCs don't match. You should repair the disk!
Partition table scan:
GPT: damaged
Caution: Found protective or hybrid MBR and corrupt GPT.
Partition info successfully found
Linux partitions is not found in image...
File successefuly loaded!

Real (Hardware) Disk/Image size: 200000 sectors 1024.0 MiB
Soft (Partitioned) Disk/Image size: 743FBC sectors 3.6 GiB
Logical sector size: 0x200 bytes
Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B
First usable sector: 34
Last usable sector: 7618526
Processing file...D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Writing as RAW data
Checking security ...
Z3X EasyJtag Software ver. 2.9.0.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:2191 mV
CMD Active Level:2789 mV
Input file : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin
Writing 0040000000 bytes to 0000000000... ROM1 (USER ROM)
Error writing address 0x38220000 Error Code:-4 Reason

ATA RCV CRC Error
Retry writing address 0x0038220000 (Attempt #0)...
Retry failed at address 0x38220000 Error Code:-4 Reason

ATA RCV CRC Error
Retry writing address 0x0038220000 (Attempt #0)...

abhishekgupt · 06-19-2018, 15:36

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 Mhz
CMD Pullup Level: 2075 mV
CMD Active Level: 2655 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101632A64393299
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 632A6439 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 3/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_632A6439_20180619_185425.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Unpacking file: sboot.bin
Unpacking file: sboot2.bin
Unpacking file: param.lfs

Partition name: SBOOT
Filename: sboot.bin , Offset: 000000400000 , filesize: 1573888 bytes
eMMC switching to ROM1
Writing partition...
Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #1
Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #2
Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #3
Too many errors. Writing has been stopped

layder · 06-20-2018, 08:16

1.5.0-1.5.1 have bug with some Hynix flash IC - bad I/O level detect

try to use 1.4.9, we try to fix it at 1.5.2

abdul alim · 03-26-2019, 12:39

I Have J100h This Problem How TO Solution

Get firmware version
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #1
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #4
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5
Too many errors. Reading has been stopped

abdul alim · 03-26-2019, 12:43

Any Body Help Me My Samsung J100H Date But Easy Jtag Repair
But Not Working

Setting frequence to 21 Mhz
CMD Pullup Level: 422 mV
CMD Active Level: 2990 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101F0281A2B5256
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: F0281A2B , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_F0281A2B_20190326_173816.extcsd
EMMC Init completed.

Get firmware version
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #1
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #4
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5
Too many errors. Reading has been stopped

layder · 03-27-2019, 12:30

Quote:

Originally Posted by abdul alim

Any Body Help Me My Samsung J100H Date But Easy Jtag Repair
But Not Working

Setting frequence to 21 Mhz
CMD Pullup Level: 422 mV
CMD Active Level: 2990 mV
EMMC Device Information :
EMMC CID: 90014A48344732621101F0281A2B5256
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: F0281A2B , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_F0281A2B_20190326_173816.extcsd
EMMC Init completed.

Get firmware version
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #1
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3
Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #4
Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5
Too many errors. Reading has been stopped

CMD pullup is low

if you use Old EasyJTAG box, you need solder pull-up resistors 100-200-500 Ohm for CMD, D_0 line or use Hipower CLK mode (connec togewer 4 pins and use usb power instead of 1,8/2,8 from adapter)

anoos1986 · 03-27-2019, 14:07

i have solution 100000%

galaxycompue · 03-29-2019, 20:48

remove emmc dont use isp then i think u get success.

royalnasim · 03-30-2019, 04:14

Salect low clock 18mhz and try again

akash48 · 04-01-2019, 11:24

bro use easy jtag plus setup

first format universal emmc

second creat partion

after write repair excsd

write room 2

room 3

room 1

ur fhone 1000ok no any error

layder · 04-01-2019, 12:00

Quote:

Originally Posted by akash48

bro use easy jtag plus setup

first format universal emmc

second creat partion

after write repair excsd

write room 2

room 3

room 1

ur fhone 1000ok no any error

1) Erase eMMC of Format
2) Write boot config
3) Write ROM1 (and ROM2/3 if needed)

bijoychowdry · 11-22-2020, 13:52

Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 36 MHz
CMD Pullup Level: 642 mV
CMD Active Level: 2023 mV
EMMC Device Information :
EMMC CID: 15010056594C30304D19B31E4BB85E61
EMMC CSD: D02701320F5903FFF6DBFFEF8A404067
EMMC Manufacture : SAMSUNG , EMMC NAME: VYL00M , HEX: 56594C30304D , S/N: B31E4BB8 , rev. 0x19
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2011
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 512 KB (000000080000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x03
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: VYL00M_B31E4BB8_20201122_184833.extcsd
EMMC Init completed.

Operation: Writing eMMC...

Writing to: ROM1 , start: 0x000000000000 , size: 0x000020000000
Input file: E:\I9100\Samsung_GT-i9100_model_dump_rom1_512mb_fixed\Samsung_GT-i9100_model_dump_rom1_512mb.BIN
eMMC switching to ROM1
Writing partition...
Error writing at address: 000000000000 , error: -8, DATA SND CRC Error(Small ROM Size, maybe) ... Retry #1
Error writing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error writing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Too many errors. Writing has been stopped

06-18-2018, 06:40	#1 (permalink)
engcobocell No Life Poster Join Date: Jun 2016 Location: every ware in your hart Posts: 798 Member: 2590583 Status: Offline Thanks Meter: 198	j100h too many error writing has been stop hi am facing these problem please can anyone help me out am new user for easy jtag plus Setting interface to EasyJtag2/ISP_HiPower Setting bus width to 1 Bit HiPower mode is ON Setting frequence to 36 Mhz CMD Pullup Level: 1824 mV CMD Active Level: 1865 mV EMMC Device Information : EMMC CID: 90014A4834473262110190A76A6082A5 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_90A76A60_20180617_222504.extcsd EMMC Init completed. Opening file: J13G.pit Pit: J13G.pit Entry count: 29 The size of the last section has been updated BL_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5 The list of files in the firmware: spl.img sboot.bin sboot2.bin param.lfs AP_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5 The list of files in the firmware: boot.img recovery.img system.img CP_J100HXXU0AQA1_CL1167865_QB12130539_REV01_user_l ow_ship.tar.md5 The list of files in the firmware: sprdcp.img sprddsp.img nvitem.bin CSC_OXE_J100HOXE0AQA1_CL1167865_QB12130539_REV01_u ser_low_ship.tar.md5 The list of files in the firmware: j13g.pit cache.img hidden.img Setting interface to EasyJtag2/ISP_HiPower Setting bus width to 1 Bit HiPower mode is ON Setting frequence to 36 Mhz CMD Pullup Level: 1824 mV CMD Active Level: 1865 mV EMMC Device Information : EMMC CID: 90014A4834473262110190A76A6082A5 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_90A76A60_20180617_222535.extcsd EMMC Init completed. Operation: Write by vendor (Samsung) Creating GPT-partitioninig Writing PrimaryGPT at address: 000000000000 Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #1 Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #2 Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #3 Too many errors. Writing has been stopped Setting interface to EasyJtag2/ISP_HiPower Setting bus width to 1 Bit HiPower mode is ON Setting frequence to 36 Mhz CMD Pullup Level: 1806 mV CMD Active Level: 1865 mV EMMC Device Information : EMMC CID: 90014A4834473262110190A76A6082A5 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 90A76A60 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_90A76A60_20180617_223145.extcsd EMMC Init completed. Operation: Write by vendor (Samsung) Creating GPT-partitioninig Writing PrimaryGPT at address: 000000000000 Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #1 Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #2 Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #3 Too many errors. Writing has been stopped

06-19-2018, 07:12	#4 (permalink)
engcobocell No Life Poster Join Date: Jun 2016 Location: every ware in your hart Posts: 798 Member: 2590583 Status: Offline Thanks Meter: 198	and now these showing am sorry am new with JTAG Loading eMMC GEN2 Firmware... IO: 2800 mV Box S/N: 16F03C9E6AE1BE10, ,FW Ver.: 02.23 CMD Pullup Level:2186 mV CMD Active Level:2551 mV Box IO Level:2800 mV CLK Rate:24000 kHz Bus Width:1bit,SDR HiPower mode is ON! ---------- eMMC Device Information ---------- EMMC CID : 90014A4834473262110190A76A6082A5 EMMC CSD : D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacturer ID: 0090 , OEM ID: 014A EMMC Date: 08/2015 Rev.0x1 EMMC NAME: H4G2b , S/N: 2426890848 EMMC NAME (HEX): 48344732622000 EMMC ROM1 (Main User Data) Capacity: 3728 MB EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No EMMC Password Locked: No Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08. H/W reset function [RST_N_FUNCTION]: 0x00 High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000] Partitioning Support [PARTITIONING_SUPPORT]: 0x07 Device support partitioning feature Device can have enhanced tech. Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00 --------------------------------------------- Backup saved: H4G2b _2426890848_20180618_2255.extcsd Done. Checking NAND Image : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin Autodetected RAW data Warning! Disk size is smaller than the main header indicates! Loading Caution: invalid backup GPT header, but valid main header! EFI Table CRC Check FAIL. Warning! One or more CRCs don't match. You should repair the disk! Partition table scan: GPT: damaged Caution: Found protective or hybrid MBR and corrupt GPT. Partition info successfully found Linux partitions is not found in image... File successefuly loaded! Real (Hardware) Disk/Image size: 200000 sectors 1024.0 MiB Soft (Partitioned) Disk/Image size: 743FBC sectors 3.6 GiB Logical sector size: 0x200 bytes Disk identifier (GUID): 52444E41-494F-2044-4D4D-43204449534B First usable sector: 34 Last usable sector: 7618526 Processing file...D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin Writing as RAW data Checking security ... Z3X EasyJtag Software ver. 2.9.0.3 Skip loading eMMC Addon Firmware CMD Pullup Level:2191 mV CMD Active Level:2789 mV Input file : D:\Compressed\SM-J100h_J100HXCU0AOD4_ROM1_OK\SM-J100h_J100HXCU0AOD4_ROM1_OK.bin Writing 0040000000 bytes to 0000000000... ROM1 (USER ROM) Error writing address 0x38220000 Error Code:-4 Reason ATA RCV CRC Error Retry writing address 0x0038220000 (Attempt #0)... Retry failed at address 0x38220000 Error Code:-4 Reason ATA RCV CRC Error Retry writing address 0x0038220000 (Attempt #0)... Retry failed at address 0x38220000 Error Code:-4 Reason ATA RCV CRC Error Retry writing address 0x0038220000 (Attempt #0)... Retry failed at address 0x38220000 Error Code:-4 Reason ATA RCV CRC Error Retry writing address 0x0038220000 (Attempt #0)...

04-01-2019, 11:24	#13 (permalink)
akash48 Freak Poster Join Date: Jun 2011 Location: jahanian punjab pakistan Posts: 153 Member: 1588653 Status: Offline Sonork: imran_Gill Thanks Meter: 83	j100h bro use easy jtag plus setup first format universal emmc second creat partion after write repair excsd write room 2 room 3 room 1 ur fhone 1000ok no any error

06-18-2018, 11:30	#2 (permalink)
engcobocell No Life Poster Join Date: Jun 2016 Location: every ware in your hart Posts: 798 Member: 2590583 Status: Offline Thanks Meter: 198	snyone can help me please thanks in advance

06-18-2018, 12:59	#3 (permalink)
pai_d Freak Poster Join Date: Sep 2009 Location: Indonesia Posts: 269 Member: 1112585 Status: Offline Sonork: 100.1645028 Thanks Meter: 91	You cannot writes data to that EMMC. Soft doesn't support or EMMC is BAD. it's SKHINIX emmc. try to uni-format/reset & repartitions. But it's not guaranteed the handset will ok for a long time. some time it just ok a week or even a day.

06-19-2018, 15:36	#5 (permalink)
abhishekgupt Junior Member Join Date: Feb 2014 Posts: 38 Member: 2130616 Status: Offline Thanks Meter: 8	Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 36 Mhz CMD Pullup Level: 2075 mV CMD Active Level: 2655 mV EMMC Device Information : EMMC CID: 90014A48344732621101632A64393299 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DB EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 632A6439 , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 3/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_632A6439_20180619_185425.extcsd EMMC Init completed. Operation: Write by vendor (Samsung) Unpacking file: sboot.bin Unpacking file: sboot2.bin Unpacking file: param.lfs Partition name: SBOOT Filename: sboot.bin , Offset: 000000400000 , filesize: 1573888 bytes eMMC switching to ROM1 Writing partition... Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #1 Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #2 Error writing at address: 000000400000 , error: 1792, 1792 Unknown error ... Retry #3 Too many errors. Writing has been stopped

06-20-2018, 08:16	#6 (permalink)
layder Product Supporter Join Date: Jun 2002 Location: Belarus Age: 47 Posts: 3,188 Member: 13148 Status: Offline Thanks Meter: 2,948	1.5.0-1.5.1 have bug with some Hynix flash IC - bad I/O level detect try to use 1.4.9, we try to fix it at 1.5.2

03-26-2019, 12:39	#7 (permalink)
abdul alim Junior Member Join Date: Jul 2010 Location: mirzapur Posts: 31 Member: 1353284 Status: Offline Sonork: mirzapur Thanks Meter: 2	I Have J100h This Problem How TO Solution Get firmware version Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #1 Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2 Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3 Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #4 Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5 Too many errors. Reading has been stopped

03-26-2019, 12:43	#8 (permalink)
abdul alim Junior Member Join Date: Jul 2010 Location: mirzapur Posts: 31 Member: 1353284 Status: Offline Sonork: mirzapur Thanks Meter: 2	Any Body Help Me My Samsung J100H Date But Easy Jtag Repair But Not Working Setting frequence to 21 Mhz CMD Pullup Level: 422 mV CMD Active Level: 2990 mV EMMC Device Information : EMMC CID: 90014A48344732621101F0281A2B5256 EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA EMMC Manufacture Name: SKHYNIX , EMMC NAME: H4G2b , EMMC NAME (HEX): 483447326200 , S/N: F0281A2B , rev. 0x01 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Manufacture Date: 5/2015 EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51) Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: H4G2b_F0281A2B_20190326_173816.extcsd EMMC Init completed. Get firmware version Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #1 Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #2 Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #3 Error reading at address: 000000000000 , error: -2, CMD CRC Error ... Retry #4 Error reading at address: 000000000000 , error: -4, DATA RCV CRC Error ... Retry #5 Too many errors. Reading has been stopped

03-27-2019, 14:07	#10 (permalink)
anoos1986 Junior Member Join Date: Apr 2007 Location: syria Age: 38 Posts: 38 Member: 490261 Status: Offline Thanks Meter: 11	i have solution 100000%

03-29-2019, 20:48	#11 (permalink)
galaxycompue No Life Poster Join Date: Nov 2014 Location: Lucknow Posts: 925 Member: 2298369 Status: Offline Thanks Meter: 440	remove emmc dont use isp then i think u get success.

03-30-2019, 04:14	#12 (permalink)
royalnasim No Life Poster Join Date: May 2009 Location: mumbai wadala Posts: 747 Member: 1037372 Status: Offline Thanks Meter: 557	Salect low clock 18mhz and try again

11-22-2020, 13:52	#15 (permalink)
bijoychowdry No Life Poster Join Date: Jul 2013 Location: gsm forum Posts: 590 Member: 1984655 Status: Offline Sonork: 119.30.39.25 Thanks Meter: 81	Setting interface to EasyJtag2/ISP_HiPower Setting bus width to 1 Bit HiPower mode is ON Setting frequence to 36 MHz CMD Pullup Level: 642 mV CMD Active Level: 2023 mV EMMC Device Information : EMMC CID: 15010056594C30304D19B31E4BB85E61 EMMC CSD: D02701320F5903FFF6DBFFEF8A404067 EMMC Manufacture : SAMSUNG , EMMC NAME: VYL00M , HEX: 56594C30304D , S/N: B31E4BB8 , rev. 0x19 EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2011 EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 512 KB (000000080000) EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.5 (MMC 4.41) Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1) Boot Bus Config: 0x01 , width 4bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x03 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: VYL00M_B31E4BB8_20201122_184833.extcsd EMMC Init completed. Operation: Writing eMMC... Writing to: ROM1 , start: 0x000000000000 , size: 0x000020000000 Input file: E:\I9100\Samsung_GT-i9100_model_dump_rom1_512mb_fixed\Samsung_GT-i9100_model_dump_rom1_512mb.BIN eMMC switching to ROM1 Writing partition... Error writing at address: 000000000000 , error: -8, DATA SND CRC Error(Small ROM Size, maybe) ... Retry #1 Error writing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2 Error writing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3 Too many errors. Writing has been stopped