Post here success logs with RIFF JTAG Manager 1.64 and fw 1.41 - Page 47 - GSM-Forum

M0YAL · 07-30-2011, 09:19

[7/30/2011 1:03:04 PM] [START OPERATION_ID = DCC_WRITE_MEMORY]
[7/30/2011 1:06:12 PM] Open serial port...OK
[7/30/2011 1:06:12 PM] Connecting to the RIFF Box...OK
[7/30/2011 1:06:12 PM] Firmware Version: 1.25, JTAG Manager Version: 1.33
[7/30/2011 1:06:12 PM] Selected Resurrector: [QSC60XX L20 D08]
[7/30/2011 1:06:12 PM]
[7/30/2011 1:06:12 PM] Connecting to the dead body...OK
[7/30/2011 1:06:12 PM] Detected dead body ID: 0x200B10E1 - CORRECT!
[7/30/2011 1:06:12 PM] Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
[7/30/2011 1:06:12 PM] Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
[7/30/2011 1:06:12 PM]
[7/30/2011 1:06:12 PM] Resurrection sequence started.
[7/30/2011 1:06:12 PM] Establish communication with the phone...OK
[7/30/2011 1:06:12 PM] Initializing internal hardware configuration...OK
[7/30/2011 1:06:12 PM] Uploading resurrector data into memory...OK
[7/30/2011 1:06:12 PM] Starting communication with resurrector...OK
[7/30/2011 1:06:12 PM]
[7/30/2011 1:06:12 PM] Detected an Initialized FLASH1 Chip ID: 0x0089/0x8852 (4MB)
[7/30/2011 1:06:12 PM]
[7/30/2011 1:06:12 PM] Writting FLASH1 memory from 0x00000000 to 0x003FFFFF
[7/30/2011 1:06:12 PM] Completed in 00:03:05.485 (Average Transfer Rate: 22.08 kB/s)
[7/30/2011 1:06:12 PM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]

sirnavid2010 · 07-30-2011, 11:22

x1 ok
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.25, JTAG Manager Version: 1.33
Selected Resurrector: [SE X1]

Connecting to the dead body...OK
Detected dead body ID: 0x201700E1 - CORRECT!
Set I/O Voltage reads as 2.63V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x002C/0x55BC (512MB)
Flashing the dead body...OK
Resurrection complete!

dr_moosavi · 07-31-2011, 11:23

dr_moosavi · 07-31-2011, 11:25

BABAK NURI · 07-31-2011, 12:43

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.34
Selected Resurrector: [Samsung i9100]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 9 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (0x03AB400000 Bytes)

Flashing the dead body...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
Resurrection complete!

amin90 · 07-31-2011, 18:24

electrolandgsm · 08-01-2011, 08:32

[IMG]

Uploaded with ImageShack.us[/IMG]

Samsung F490 resurection and full flash done.
phone revived and working.

jay19x · 08-01-2011, 11:55

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.34
Selected Resurrector: [SE X10]

Connecting to the dead body...OK
Detected dead body ID: 0x202400E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x002C/0x55B3 (1024MB)
Selected Resurrection Data for the NAND Chip with Page size = 2KB

Flashing the dead body...OK
Resurrection complete!

X10i

uniontelecom · 08-01-2011, 12:40

REPAIR C3010 AFTER resurrection TATA LOGO BLANK PROBLM SOLV WITH RIFF BOX

here is solutions

flash your phone with this UNLOCK dump file Free File Hosting & Video Downloads, Free File Sharing, Online Friends Network - Ziddu

AFTER FLASH AGAIN resurrect USING resurrection BUTTON

LOG

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.34
Selected Resurrector: [Haier C3010]

Connecting to the dead body...OK
Detected dead body ID: 0x200B10E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x017E/0x2210 (8MB)
Selected Resurrection Data for the NOR Chip with IDs: 0x017E/0x2210

Flashing the dead body...OK
Resurrection complete!

YOUR PROBLM SOLV TESTED BY ME

VICKY

mayank.gupta · 08-01-2011, 14:37

huwaie 5330 sucessfully unlocked

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.25, JTAG Manager Version: 1.33
Selected Resurrector: [QSC60XX L24 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x200B30E1 - IGNORED!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 4 MHz]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x017E/0x2230 (32MB)

Writting FLASH1 memory from 0x00000000 to 0x01FFFFFF
Completed in 00:19:45.063 (Average Transfer Rate: 27.65 kB/s)

amin90 · 08-01-2011, 14:45

[CENTER]

aashir · 08-01-2011, 14:48

samsung s8500
----------------------
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.21, JTAG Manager Version: 1.29
Selected Resurrector: [Samsung S8500]

Connecting to the dead body...OK
Detected dead body ID: 0x1BA00477 - CORRECT!
Set I/O Voltage reads as 2.78V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB)
Flashing the dead body...OK
Resurrection complete!

mayank.gupta · 08-01-2011, 16:00

huwaie 5330 sucessfully unlocked

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.25, JTAG Manager Version: 1.33
Selected Resurrector: [QSC60XX L24 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x200B30E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 4 MHz]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip ID: 0x017E/0x2230 (32MB)

Writting FLASH1 memory from 0x00000000 to 0x01FFFFFF
Completed in 00:16:19.281 (Average Transfer Rate: 33.46 kB/s)

MOHIT_THAREJA · 08-01-2011, 17:25

unicare r150b blinking done

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.34
Selected Resurrector: [QSC60XX L24 D08]

Connecting to the dead body...OK
Detected dead body ID: 0x200B10E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0098/0x0096 (8MB)

Writting FLASH1 memory from 0x0000000000 to 0x00007FFFFF
Completed in 00:04:38.250 (Average Transfer Rate: 29.44 kB/s)

MOHIT_THAREJA · 08-02-2011, 09:03

samsung b619 dead recover done

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.26, JTAG Manager Version: 1.34
Selected Resurrector: [Samsung B619]

Connecting to the dead body...OK
Detected dead body ID: 0x220B10E1 - CORRECT!
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x2402 (16MB)
Selected Resurrection Data for the NOR Chip with IDs: 0x00EC/0x2402

Flashing the dead body...OK
Resurrection complete!

07-30-2011, 11:22	#692 (permalink)
sirnavid2010 No Life Poster Join Date: May 2008 Location: persian Age: 43 Posts: 3,820 Member: 777729 Status: Offline Sonork: 100.1616470 Thanks Meter: 824	x1 ok Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.25, JTAG Manager Version: 1.33 Selected Resurrector: [SE X1] Connecting to the dead body...OK Detected dead body ID: 0x201700E1 - CORRECT! Set I/O Voltage reads as 2.63V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x002C/0x55BC (512MB) Flashing the dead body...OK Resurrection complete!

07-31-2011, 11:23	#693 (permalink)
dr_moosavi Product Supporter Join Date: Jul 2008 Location: iran-shiraz Posts: 730 Member: 814775 Status: Offline Sonork: 100.1587334 Thanks Meter: 973

07-31-2011, 11:25	#694 (permalink)
dr_moosavi Product Supporter Join Date: Jul 2008 Location: iran-shiraz Posts: 730 Member: 814775 Status: Offline Sonork: 100.1587334 Thanks Meter: 973

07-31-2011, 12:43	#695 (permalink)
BABAK NURI Product Supporter Join Date: Mar 2005 Location: Tehran.IR Age: 43 Posts: 7,259 Member: 131131 Status: Offline Sonork: 100.1606847 Thanks Meter: 4,475	Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.34 Selected Resurrector: [Samsung i9100] Connecting to the dead body...OK Detected dead body ID: 0x4BA00477 - CORRECT! Set I/O Voltage reads as 2.79V, TCK Frequency is 9 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (0x03AB400000 Bytes) Flashing the dead body...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK Resurrection complete!

07-31-2011, 18:24	#696 (permalink)
amin90 Registered User Join Date: Oct 2009 Location: iran Posts: 52 Member: 1139698 Status: Offline Sonork: 100.1603147 Thanks Meter: 6

08-01-2011, 08:32	#697 (permalink)
electrolandgsm No Life Poster Join Date: Aug 2005 Location: romania-bm Age: 40 Posts: 1,422 Member: 174315 Status: Offline Thanks Meter: 123	[IMG] Uploaded with ImageShack.us[/IMG] Samsung F490 resurection and full flash done. phone revived and working.

08-01-2011, 12:40	#699 (permalink)
uniontelecom No Life Poster Join Date: Mar 2011 Location: FIND ME Age: 32 Posts: 751 Member: 1538904 Status: Offline Sonork: 100.1603095 Thanks Meter: 198	REPAIR C3010 AFTER resurrection TATA LOGO BLANK PROBLM SOLV WITH RIFF BOX here is solutions flash your phone with this UNLOCK dump file Free File Hosting & Video Downloads, Free File Sharing, Online Friends Network - Ziddu AFTER FLASH AGAIN resurrect USING resurrection BUTTON LOG Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.34 Selected Resurrector: [Haier C3010] Connecting to the dead body...OK Detected dead body ID: 0x200B10E1 - CORRECT! Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at MAX] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x017E/0x2210 (8MB) Selected Resurrection Data for the NOR Chip with IDs: 0x017E/0x2210 Flashing the dead body...OK Resurrection complete! YOUR PROBLM SOLV TESTED BY ME VICKY

08-01-2011, 14:37	#700 (permalink)
mayank.gupta No Life Poster Join Date: Feb 2009 Posts: 845 Member: 966792 Status: Offline Sonork: 100.1602610 Thanks Meter: 199	huwaie 5330 sucessfully unlocked Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.25, JTAG Manager Version: 1.33 Selected Resurrector: [QSC60XX L24 D08] Connecting to the dead body...OK Detected dead body ID: 0x200B30E1 - IGNORED! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 4 MHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x017E/0x2230 (32MB) Writting FLASH1 memory from 0x00000000 to 0x01FFFFFF Completed in 00:19:45.063 (Average Transfer Rate: 27.65 kB/s)

08-01-2011, 14:45	#701 (permalink)
amin90 Registered User Join Date: Oct 2009 Location: iran Posts: 52 Member: 1139698 Status: Offline Sonork: 100.1603147 Thanks Meter: 6	[CENTER]

08-01-2011, 14:48	#702 (permalink)
aashir No Life Poster Join Date: Jan 2004 Location: india Posts: 1,450 Member: 50772 Status: Online Sonork: 100.1590990 Thanks Meter: 318	samsung s8500 ---------------------- Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.21, JTAG Manager Version: 1.29 Selected Resurrector: [Samsung S8500] Connecting to the dead body...OK Detected dead body ID: 0x1BA00477 - CORRECT! Set I/O Voltage reads as 2.78V, TCK Frequency is 8 MHz Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x00EC/0x0050 (512MB) Flashing the dead body...OK Resurrection complete!

08-01-2011, 16:00	#703 (permalink)
mayank.gupta No Life Poster Join Date: Feb 2009 Posts: 845 Member: 966792 Status: Offline Sonork: 100.1602610 Thanks Meter: 199	huwaie 5330 sucessfully unlocked Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.25, JTAG Manager Version: 1.33 Selected Resurrector: [QSC60XX L24 D08] Connecting to the dead body...OK Detected dead body ID: 0x200B30E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 4 MHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip ID: 0x017E/0x2230 (32MB) Writting FLASH1 memory from 0x00000000 to 0x01FFFFFF Completed in 00:16:19.281 (Average Transfer Rate: 33.46 kB/s)

08-01-2011, 17:25	#704 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	unicare r150b blinking done Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.34 Selected Resurrector: [QSC60XX L24 D08] Connecting to the dead body...OK Detected dead body ID: 0x200B10E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x0098/0x0096 (8MB) Writting FLASH1 memory from 0x0000000000 to 0x00007FFFFF Completed in 00:04:38.250 (Average Transfer Rate: 29.44 kB/s)

08-02-2011, 09:03	#705 (permalink)
MOHIT_THAREJA No Life Poster Join Date: Oct 2009 Location: India [UNKNOWN] Posts: 3,257 Member: 1143809 Status: Offline Sonork: 100.1602432 Thanks Meter: 574	samsung b619 dead recover done Open serial port...OK Connecting to the RIFF Box...OK Firmware Version: 1.26, JTAG Manager Version: 1.34 Selected Resurrector: [Samsung B619] Connecting to the dead body...OK Detected dead body ID: 0x220B10E1 - CORRECT! Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] Resurrection sequence started. Establish communication with the phone...OK Initializing internal hardware configuration...OK Uploading resurrector data into memory...OK Starting communication with resurrector...OK Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x2402 (16MB) Selected Resurrection Data for the NOR Chip with IDs: 0x00EC/0x2402 Flashing the dead body...OK Resurrection complete!